diff options
16 files changed, 1341 insertions, 1465 deletions
diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts new file mode 100644 index 0000000000..af20cf9e2c --- /dev/null +++ b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-goflexhome.dts @@ -0,0 +1,124 @@ +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "Seagate GoFlex Home"; + compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + aliases { + led-boot = &led_health; + led-failsafe = &led_fault; + led-running = &led_health; + led-upgrade = &led_fault; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; + stdout-path = &uart0; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pmx_usb_power_enable: pmx-usb-power-enable { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + pmx_led_white: pmx-led-white { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + pmx_led_green: pmx-led_green { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + pmx_led_orange: pmx-led-orange { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + }; + serial@12000 { + status = "ok"; + }; + + sata@80000 { + status = "okay"; + nr-ports = <2>; + }; + + }; + gpio-leds { + compatible = "gpio-leds"; + + led_health: health { + label = "status:green:health"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led_fault: fault { + label = "status:orange:fault"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + misc { + label = "status:white:misc"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + linux,default-trigger = "disk-activity"; + }; + }; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_power_enable>; + pinctrl-names = "default"; + + usb_power: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&nand { + chip-delay = <40>; + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "ubi"; + reg = <0x100000 0x0ff00000>; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts new file mode 100644 index 0000000000..004ce10219 --- /dev/null +++ b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-linksys-audi.dts @@ -0,0 +1,250 @@ +/* + * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500 + * + * (c) 2013 Jonas Gorski <jogo@openwrt.org> + * (c) 2013 Deutsche Telekom Innovation Laboratories + * (c) 2014 Luka Perkov <luka@openwrt.org> + * (c) 2014 Dan Walters <dan@walters.io> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" + +/ { + model = "Linksys Audi (EA3500)"; + compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >; + pinctrl-names = "default"; + + wps { + label = "WPS Button"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = < &pmx_led_green_power >; + pinctrl-names = "default"; + + led_power: power { + label = "audi:green:power"; + gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + mvsw61xx { + compatible = "marvell,88e6171"; + status = "okay"; + reg = <0x10>; + + mii-bus = <&mdio>; + cpu-port-0 = <5>; + cpu-port-1 = <6>; + is-indirect; + }; + + dsa { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + dsa,ethernet = <ð0port>; + dsa,mii-bus = <&mdio>; + + switch@16,0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <16 0>; /* MDIO address 16, switch 0 in tree */ + + port@0 { + reg = <0>; + label = "ethernet1"; + }; + + port@1 { + reg = <1>; + label = "ethernet2"; + }; + + port@2 { + reg = <2>; + label = "ethernet3"; + }; + + port@3 { + reg = <3>; + label = "ethernet4"; + }; + + port@4 { + reg = <4>; + label = "internet"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + }; + }; +}; + +&pinctrl { + pmx_led_green_power: pmx-led-green-power { + marvell,pins = "mpp7"; + marvell,function = "gpo"; + }; + pmx_btn_wps: pmx-btn-wps { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + pmx_btn_reset: pmx-btn-reset { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; +}; + +&nand { + status = "okay"; + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "u_env"; + reg = <0x80000 0x4000>; + }; + + partition@84000 { + label = "s_env"; + reg = <0x84000 0x4000>; + }; + + partition@200000 { + label = "kernel1"; + reg = <0x200000 0x290000>; + }; + + partition@490000 { + label = "rootfs1"; + reg = <0x490000 0x1170000>; + }; + + partition@1600000 { + label = "kernel2"; + reg = <0x1600000 0x290000>; + }; + + partition@1890000 { + label = "rootfs2"; + reg = <0x1890000 0x1170000>; + }; + + partition@2a00000 { + label = "syscfg"; + reg = <0x2a00000 0x1600000>; + }; + + partition@88000 { + label = "unused"; + reg = <0x88000 0x178000>; + }; + + }; +}; + +&pciec { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&mdio { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set + * fixed speed and duplex. + */ +ð0 { + status = "okay"; + ethernet0-port@0 { + speed = <1000>; + duplex = <1>; + }; +}; + +/* eth1 is connected to the switch at port 6. However DSA only supports a + * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. + */ +ð1 { + status = "okay"; + ethernet1-port@0 { + speed = <1000>; + duplex = <1>; + }; +}; + +/* There is no battery on the board, so the RTC does not keep + * time when there is no power, making it useless. + */ +&rtc { + status = "disabled"; +}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts new file mode 100644 index 0000000000..a83a55af07 --- /dev/null +++ b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-nsa310b.dts @@ -0,0 +1,132 @@ +/dts-v1/; + +#include "kirkwood-nsa3x0-common.dtsi" + +/* + * There are at least two different NSA310 designs. This variant has + * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller. + */ + +/ { + model = "ZyXEL NSA310b"; + compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + aliases { + led-boot = &led_green_sys; + led-failsafe = &led_red_sys; + led-running = &led_green_sys; + led-upgrade = &led_red_sys; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pinctrl-names = "default"; + + pmx_led_esata_green: pmx-led-esata-green { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_led_esata_red: pmx-led-esata-red { + marvell,pins = "mpp13"; + marvell,function = "gpio"; + }; + + pmx_led_usb_green: pmx-led-usb-green { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_led_usb_red: pmx-led-usb-red { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_led_sys_green: pmx-led-sys-green { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_led_sys_red: pmx-led-sys-red { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_led_hdd_green: pmx-led-hdd-green { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + pmx_led_hdd_red: pmx-led-hdd-red { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + }; + + i2c@11000 { + status = "okay"; + + lm85: lm85@2e { + compatible = "national,lm85"; + reg = <0x2e>; + }; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_green_sys: green-sys { + label = "nsa310:green:sys"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + led_red_sys: red-sys { + label = "nsa310:red:sys"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + green-hdd { + label = "nsa310:green:hdd"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + red-hdd { + label = "nsa310:red:hdd"; + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; + green-esata { + label = "nsa310:green:esata"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + red-esata { + label = "nsa310:red:esata"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + green-usb { + label = "nsa310:green:usb"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + red-usb { + label = "nsa310:red:usb"; + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + }; + green-copy { + label = "nsa310:green:copy"; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; + red-copy { + label = "nsa310:red:copy"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; + }; +}; diff --git a/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts new file mode 100644 index 0000000000..9296c3fc71 --- /dev/null +++ b/target/linux/kirkwood/files-4.14/arch/arm/boot/dts/kirkwood-on100.dts @@ -0,0 +1,165 @@ +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" + +/ { + model = "Cisco Systems ON100"; + compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + aliases { + led-boot = &led_health_green; + led-failsafe = &led_health_red; + led-running = &led_health_green; + led-upgrade = &led_health_red; + serial0 = &uart0; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_btn_reset>; + pinctrl-names = "default"; + + button@1 { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; + pinctrl-names = "default"; + + led_health_green: health_green { + label = "on100:green:health"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + led_health_red: health_red { + label = "on100:red:health"; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + + health2_green { + label = "on100:green:health2"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + }; + + health2_red { + label = "on100:red:health2"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð0 { + status = "okay"; + + ethernet0-port@0 { + phy-handle = <ðphy0>; + phy-connection-type = "rgmii-id"; + }; +}; + +ð1 { + status = "okay"; + + ethernet1-port@0 { + phy-handle = <ðphy1>; + phy-connection-type = "rgmii-id"; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + /* Marvell 88E1121R */ + compatible = "ethernet-phy-id0141.0cb0", + "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + /* Marvell 88E1121R */ + compatible = "ethernet-phy-id0141.0cb0", + "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&nand { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x000a0000>; + read-only; + }; + + partition@a0000 { + label = "u-boot environment"; + reg = <0x000a0000 0x00020000>; + read-only; + }; + + partition@c0000 { + label = "kernel"; + reg = <0x000c0000 0x00540000>; + }; + + partition@600000 { + label = "ubi"; + reg = <0x00600000 0x1fa00000>; + }; +}; + +&pinctrl { + pmx_led_health_r: pmx-led-health-r { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_led_health_g: pmx-led-health-g { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_led_health2_r: pmx-led-health2-r { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + + pmx_led_health2_g: pmx-led-health2-g { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + + pmx_btn_reset: pmx-led-reset { + marvell,pins = "mpp31"; + marvell,function = "gpio"; + }; +}; + +&sdio { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; diff --git a/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-goflexhome.dts b/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-goflexhome.dts new file mode 100644 index 0000000000..6cb6f7249e --- /dev/null +++ b/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-goflexhome.dts @@ -0,0 +1,124 @@ +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "Seagate GoFlex Home"; + compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + aliases { + led-boot = &led_health; + led-failsafe = &led_fault; + led-running = &led_health; + led-upgrade = &led_fault; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; + stdout-path = &uart0; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pmx_usb_power_enable: pmx-usb-power-enable { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + pmx_led_white: pmx-led-white { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + pmx_led_green: pmx-led_green { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + pmx_led_orange: pmx-led-orange { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + }; + serial@12000 { + status = "ok"; + }; + + sata@80000 { + status = "okay"; + nr-ports = <2>; + }; + + }; + gpio-leds { + compatible = "gpio-leds"; + + led_health: health { + label = "status:green:health"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led_fault: fault { + label = "status:orange:fault"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + misc { + label = "status:white:misc"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + linux,default-trigger = "disk-activity"; + }; + }; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_power_enable>; + pinctrl-names = "default"; + + usb_power: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&nand { + chip-delay = <40>; + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "ubi"; + reg = <0x100000 0x0ff00000>; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; diff --git a/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-linksys-audi.dts b/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-linksys-audi.dts new file mode 100644 index 0000000000..ac9db1949c --- /dev/null +++ b/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-linksys-audi.dts @@ -0,0 +1,251 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500 + * + * (c) 2013 Jonas Gorski <jogo@openwrt.org> + * (c) 2013 Deutsche Telekom Innovation Laboratories + * (c) 2014 Luka Perkov <luka@openwrt.org> + * (c) 2014 Dan Walters <dan@walters.io> + * + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" + +/ { + model = "Linksys Audi (EA3500)"; + compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x4000000>; + }; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >; + pinctrl-names = "default"; + + wps { + label = "WPS Button"; + linux,code = <KEY_WPS_BUTTON>; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + + reset { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = < &pmx_led_green_power >; + pinctrl-names = "default"; + + led_power: power { + label = "audi:green:power"; + gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + switches { + #address-cells = <1>; + #size-cells = <0>; + + mvsw61xx@10 { + compatible = "marvell,88e6171"; + status = "okay"; + reg = <0x10>; + + mii-bus = <&mdio>; + cpu-port-0 = <5>; + cpu-port-1 = <6>; + is-indirect; + }; + }; + + dsa { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + dsa,ethernet = <ð0port>; + dsa,mii-bus = <&mdio>; + + switch@16,0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <16 0>; /* MDIO address 16, switch 0 in tree */ + + port@0 { + reg = <0>; + label = "ethernet1"; + }; + + port@1 { + reg = <1>; + label = "ethernet2"; + }; + + port@2 { + reg = <2>; + label = "ethernet3"; + }; + + port@3 { + reg = <3>; + label = "ethernet4"; + }; + + port@4 { + reg = <4>; + label = "internet"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + }; + }; +}; + +&pinctrl { + pmx_led_green_power: pmx-led-green-power { + marvell,pins = "mpp7"; + marvell,function = "gpo"; + }; + pmx_btn_wps: pmx-btn-wps { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + pmx_btn_reset: pmx-btn-reset { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; +}; + +&nand { + status = "okay"; + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x80000>; + read-only; + }; + + partition@80000 { + label = "u_env"; + reg = <0x80000 0x4000>; + }; + + partition@84000 { + label = "s_env"; + reg = <0x84000 0x4000>; + }; + + partition@200000 { + label = "kernel1"; + reg = <0x200000 0x290000>; + }; + + partition@490000 { + label = "rootfs1"; + reg = <0x490000 0x1170000>; + }; + + partition@1600000 { + label = "kernel2"; + reg = <0x1600000 0x290000>; + }; + + partition@1890000 { + label = "rootfs2"; + reg = <0x1890000 0x1170000>; + }; + + partition@2a00000 { + label = "syscfg"; + reg = <0x2a00000 0x1600000>; + }; + + partition@88000 { + label = "unused"; + reg = <0x88000 0x178000>; + }; + + }; +}; + +&pciec { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pcie1 { + status = "okay"; +}; + +&mdio { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set + * fixed speed and duplex. + */ +ð0 { + status = "okay"; + ethernet0-port@0 { + speed = <1000>; + duplex = <1>; + }; +}; + +/* eth1 is connected to the switch at port 6. However DSA only supports a + * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. + */ +ð1 { + status = "okay"; + ethernet1-port@0 { + speed = <1000>; + duplex = <1>; + }; +}; + +/* There is no battery on the board, so the RTC does not keep + * time when there is no power, making it useless. + */ +&rtc { + status = "disabled"; +}; diff --git a/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-nsa310b.dts b/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-nsa310b.dts new file mode 100644 index 0000000000..b06848576a --- /dev/null +++ b/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-nsa310b.dts @@ -0,0 +1,132 @@ +/dts-v1/; + +#include "kirkwood-nsa3x0-common.dtsi" + +/* + * There are at least two different NSA310 designs. This variant has + * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller. + */ + +/ { + model = "ZyXEL NSA310b"; + compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + aliases { + led-boot = &led_green_sys; + led-failsafe = &led_red_sys; + led-running = &led_green_sys; + led-upgrade = &led_red_sys; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + ocp@f1000000 { + pinctrl: pin-controller@10000 { + pinctrl-names = "default"; + + pmx_led_esata_green: pmx-led-esata-green { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_led_esata_red: pmx-led-esata-red { + marvell,pins = "mpp13"; + marvell,function = "gpio"; + }; + + pmx_led_usb_green: pmx-led-usb-green { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_led_usb_red: pmx-led-usb-red { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_led_sys_green: pmx-led-sys-green { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_led_sys_red: pmx-led-sys-red { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_led_hdd_green: pmx-led-hdd-green { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + pmx_led_hdd_red: pmx-led-hdd-red { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + }; + + i2c@11000 { + status = "okay"; + + lm85: lm85@2e { + compatible = "national,lm85"; + reg = <0x2e>; + }; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_green_sys: green-sys { + label = "nsa310:green:sys"; + gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + led_red_sys: red-sys { + label = "nsa310:red:sys"; + gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + green-hdd { + label = "nsa310:green:hdd"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + red-hdd { + label = "nsa310:red:hdd"; + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; + green-esata { + label = "nsa310:green:esata"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + }; + red-esata { + label = "nsa310:red:esata"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + green-usb { + label = "nsa310:green:usb"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; + }; + red-usb { + label = "nsa310:red:usb"; + gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + }; + green-copy { + label = "nsa310:green:copy"; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + }; + red-copy { + label = "nsa310:red:copy"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; + }; +}; diff --git a/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-on100.dts b/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-on100.dts new file mode 100644 index 0000000000..6d45814050 --- /dev/null +++ b/target/linux/kirkwood/files-4.19/arch/arm/boot/dts/kirkwood-on100.dts @@ -0,0 +1,163 @@ +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" + +/ { + model = "Cisco Systems ON100"; + compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + aliases { + led-boot = &led_health_green; + led-failsafe = &led_health_red; + led-running = &led_health_green; + led-upgrade = &led_health_red; + serial0 = &uart0; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + stdout-path = "serial0:115200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-0 = <&pmx_btn_reset>; + pinctrl-names = "default"; + + reset { + label = "Reset Button"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; + pinctrl-names = "default"; + + led_health_green: health_green { + label = "on100:green:health"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + led_health_red: health_red { + label = "on100:red:health"; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + + health2_green { + label = "on100:green:health2"; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + }; + + health2_red { + label = "on100:red:health2"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð0 { + status = "okay"; + + ethernet0-port@0 { + phy-handle = <ðphy0>; + phy-connection-type = "rgmii-id"; + }; +}; + +ð1 { + status = "okay"; + + ethernet1-port@0 { + phy-handle = <ðphy1>; + phy-connection-type = "rgmii-id"; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + /* Marvell 88E1121R */ + compatible = "ethernet-phy-id0141.0cb0", + "ethernet-phy-ieee802.3-c22"; + reg = <0>; + }; + + ethphy1: ethernet-phy@1 { + /* Marvell 88E1121R */ + compatible = "ethernet-phy-id0141.0cb0", + "ethernet-phy-ieee802.3-c22"; + reg = <1>; + }; +}; + +&nand { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x000a0000>; + read-only; + }; + + partition@a0000 { + label = "u-boot environment"; + reg = <0x000a0000 0x00020000>; + read-only; + }; + + partition@c0000 { + label = "kernel"; + reg = <0x000c0000 0x00540000>; + }; + + partition@600000 { + label = "ubi"; + reg = <0x00600000 0x1fa00000>; + }; +}; + +&pinctrl { + pmx_led_health_r: pmx-led-health-r { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_led_health_g: pmx-led-health-g { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_led_health2_r: pmx-led-health2-r { + marvell,pins = "mpp47"; + marvell,function = "gpio"; + }; + + pmx_led_health2_g: pmx-led-health2-g { + marvell,pins = "mpp46"; + marvell,function = "gpio"; + }; + + pmx_btn_reset: pmx-led-reset { + marvell,pins = "mpp31"; + marvell,function = "gpio"; + }; +}; + +&sdio { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; diff --git a/target/linux/kirkwood/patches-4.14/104-ea3500.patch b/target/linux/kirkwood/patches-4.14/104-ea3500.patch deleted file mode 100644 index 851875c645..0000000000 --- a/target/linux/kirkwood/patches-4.14/104-ea3500.patch +++ /dev/null @@ -1,263 +0,0 @@ ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -250,6 +250,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-linkstation-lswsxl.dtb \ - kirkwood-linkstation-lswvl.dtb \ - kirkwood-linkstation-lswxl.dtb \ -+ kirkwood-linksys-audi.dtb \ - kirkwood-linksys-viper.dtb \ - kirkwood-lschlv2.dtb \ - kirkwood-lsxhl.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts -@@ -0,0 +1,250 @@ -+/* -+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500 -+ * -+ * (c) 2013 Jonas Gorski <jogo@openwrt.org> -+ * (c) 2013 Deutsche Telekom Innovation Laboratories -+ * (c) 2014 Luka Perkov <luka@openwrt.org> -+ * (c) 2014 Dan Walters <dan@walters.io> -+ * -+ * This file is licensed under the terms of the GNU General Public -+ * License version 2. This program is licensed "as is" without any -+ * warranty of any kind, whether express or implied. -+ */ -+ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6282.dtsi" -+ -+/ { -+ model = "Linksys Audi (EA3500)"; -+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood"; -+ -+ memory { -+ device_type = "memory"; -+ reg = <0x00000000 0x4000000>; -+ }; -+ -+ aliases { -+ led-boot = &led_power; -+ led-failsafe = &led_power; -+ led-running = &led_power; -+ led-upgrade = &led_power; -+ serial0 = &uart0; -+ }; -+ -+ chosen { -+ stdout-path = "serial0:115200n8"; -+ }; -+ -+ gpio_keys { -+ compatible = "gpio-keys"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >; -+ pinctrl-names = "default"; -+ -+ wps { -+ label = "WPS Button"; -+ linux,code = <KEY_WPS_BUTTON>; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ -+ reset { -+ label = "Reset Button"; -+ linux,code = <KEY_RESTART>; -+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ pinctrl-0 = < &pmx_led_green_power >; -+ pinctrl-names = "default"; -+ -+ led_power: power { -+ label = "audi:green:power"; -+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; -+ default-state = "on"; -+ }; -+ }; -+ -+ mvsw61xx { -+ compatible = "marvell,88e6171"; -+ status = "okay"; -+ reg = <0x10>; -+ -+ mii-bus = <&mdio>; -+ cpu-port-0 = <5>; -+ cpu-port-1 = <6>; -+ is-indirect; -+ }; -+ -+ dsa { -+ compatible = "marvell,dsa"; -+ #address-cells = <2>; -+ #size-cells = <0>; -+ -+ dsa,ethernet = <ð0port>; -+ dsa,mii-bus = <&mdio>; -+ -+ switch@16,0 { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ reg = <16 0>; /* MDIO address 16, switch 0 in tree */ -+ -+ port@0 { -+ reg = <0>; -+ label = "ethernet1"; -+ }; -+ -+ port@1 { -+ reg = <1>; -+ label = "ethernet2"; -+ }; -+ -+ port@2 { -+ reg = <2>; -+ label = "ethernet3"; -+ }; -+ -+ port@3 { -+ reg = <3>; -+ label = "ethernet4"; -+ }; -+ -+ port@4 { -+ reg = <4>; -+ label = "internet"; -+ }; -+ -+ port@5 { -+ reg = <5>; -+ label = "cpu"; -+ }; -+ }; -+ }; -+}; -+ -+&pinctrl { -+ pmx_led_green_power: pmx-led-green-power { -+ marvell,pins = "mpp7"; -+ marvell,function = "gpo"; -+ }; -+ pmx_btn_wps: pmx-btn-wps { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ pmx_btn_reset: pmx-btn-reset { -+ marvell,pins = "mpp48"; -+ marvell,function = "gpio"; -+ }; -+}; -+ -+&nand { -+ status = "okay"; -+ pinctrl-0 = <&pmx_nand>; -+ pinctrl-names = "default"; -+ -+ partitions { -+ compatible = "fixed-partitions"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x0 0x80000>; -+ read-only; -+ }; -+ -+ partition@80000 { -+ label = "u_env"; -+ reg = <0x80000 0x4000>; -+ }; -+ -+ partition@84000 { -+ label = "s_env"; -+ reg = <0x84000 0x4000>; -+ }; -+ -+ partition@200000 { -+ label = "kernel1"; -+ reg = <0x200000 0x290000>; -+ }; -+ -+ partition@490000 { -+ label = "rootfs1"; -+ reg = <0x490000 0x1170000>; -+ }; -+ -+ partition@1600000 { -+ label = "kernel2"; -+ reg = <0x1600000 0x290000>; -+ }; -+ -+ partition@1890000 { -+ label = "rootfs2"; -+ reg = <0x1890000 0x1170000>; -+ }; -+ -+ partition@2a00000 { -+ label = "syscfg"; -+ reg = <0x2a00000 0x1600000>; -+ }; -+ -+ partition@88000 { -+ label = "unused"; -+ reg = <0x88000 0x178000>; -+ }; -+ -+ }; -+}; -+ -+&pciec { -+ status = "okay"; -+}; -+ -+&pcie0 { -+ status = "okay"; -+}; -+ -+&pcie1 { -+ status = "okay"; -+}; -+ -+&mdio { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; -+ -+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set -+ * fixed speed and duplex. -+ */ -+ð0 { -+ status = "okay"; -+ ethernet0-port@0 { -+ speed = <1000>; -+ duplex = <1>; -+ }; -+}; -+ -+/* eth1 is connected to the switch at port 6. However DSA only supports a -+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. -+ */ -+ð1 { -+ status = "okay"; -+ ethernet1-port@0 { -+ speed = <1000>; -+ duplex = <1>; -+ }; -+}; -+ -+/* There is no battery on the board, so the RTC does not keep -+ * time when there is no power, making it useless. -+ */ -+&rtc { -+ status = "disabled"; -+}; diff --git a/target/linux/kirkwood/patches-4.14/105-goflexhome.patch b/target/linux/kirkwood/patches-4.14/105-goflexhome.patch deleted file mode 100644 index fcccbf7f39..0000000000 --- a/target/linux/kirkwood/patches-4.14/105-goflexhome.patch +++ /dev/null @@ -1,137 +0,0 @@ ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -237,6 +237,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-ds411.dtb \ - kirkwood-ds411j.dtb \ - kirkwood-ds411slim.dtb \ -+ kirkwood-goflexhome.dtb \ - kirkwood-goflexnet.dtb \ - kirkwood-guruplug-server-plus.dtb \ - kirkwood-ib62x0.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts -@@ -0,0 +1,124 @@ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6281.dtsi" -+ -+/ { -+ model = "Seagate GoFlex Home"; -+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood"; -+ -+ aliases { -+ led-boot = &led_health; -+ led-failsafe = &led_fault; -+ led-running = &led_health; -+ led-upgrade = &led_fault; -+ }; -+ -+ memory { -+ device_type = "memory"; -+ reg = <0x00000000 0x8000000>; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; -+ stdout-path = &uart0; -+ }; -+ -+ ocp@f1000000 { -+ pinctrl: pin-controller@10000 { -+ pmx_usb_power_enable: pmx-usb-power-enable { -+ marvell,pins = "mpp29"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_white: pmx-led-white { -+ marvell,pins = "mpp40"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_green: pmx-led_green { -+ marvell,pins = "mpp46"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_orange: pmx-led-orange { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ }; -+ serial@12000 { -+ status = "ok"; -+ }; -+ -+ sata@80000 { -+ status = "okay"; -+ nr-ports = <2>; -+ }; -+ -+ }; -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ led_health: health { -+ label = "status:green:health"; -+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; -+ default-state = "on"; -+ }; -+ led_fault: fault { -+ label = "status:orange:fault"; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ misc { -+ label = "status:white:misc"; -+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; -+ linux,default-trigger = "disk-activity"; -+ }; -+ }; -+ regulators { -+ compatible = "simple-bus"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ pinctrl-0 = <&pmx_usb_power_enable>; -+ pinctrl-names = "default"; -+ -+ usb_power: regulator@1 { -+ compatible = "regulator-fixed"; -+ reg = <1>; -+ regulator-name = "USB Power"; -+ regulator-min-microvolt = <5000000>; -+ regulator-max-microvolt = <5000000>; -+ enable-active-high; -+ regulator-always-on; -+ regulator-boot-on; -+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+}; -+ -+&nand { -+ chip-delay = <40>; -+ status = "okay"; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x0000000 0x100000>; -+ read-only; -+ }; -+ -+ partition@100000 { -+ label = "ubi"; -+ reg = <0x100000 0x0ff00000>; -+ }; -+}; -+ -+&mdio { -+ status = "okay"; -+ -+ ethphy0: ethernet-phy@0 { -+ reg = <0>; -+ }; -+}; -+ -+ð0 { -+ status = "okay"; -+ ethernet0-port@0 { -+ phy-handle = <ðphy0>; -+ }; -+}; diff --git a/target/linux/kirkwood/patches-4.14/107-02-nsa310b.patch b/target/linux/kirkwood/patches-4.14/107-02-nsa310b.patch deleted file mode 100644 index 1f2718fb80..0000000000 --- a/target/linux/kirkwood/patches-4.14/107-02-nsa310b.patch +++ /dev/null @@ -1,155 +0,0 @@ -kirkwood: add nsa310b dtb, a zyxel nsa310 variant - -add support to a nsa310 variant with red/green usb led -and lm85 temp/fan controller - -Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> - -NOTE: this patch can be upstreamed as-is, LEDE-specific - nand partitions are set in another patch - ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -268,6 +268,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-ns2mini.dtb \ - kirkwood-nsa310.dtb \ - kirkwood-nsa310a.dtb \ -+ kirkwood-nsa310b.dtb \ - kirkwood-nsa320.dtb \ - kirkwood-nsa325.dtb \ - kirkwood-openblocks_a6.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts -@@ -0,0 +1,132 @@ -+/dts-v1/; -+ -+#include "kirkwood-nsa3x0-common.dtsi" -+ -+/* -+ * There are at least two different NSA310 designs. This variant has -+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller. -+ */ -+ -+/ { -+ model = "ZyXEL NSA310b"; -+ compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood"; -+ -+ aliases { -+ led-boot = &led_green_sys; -+ led-failsafe = &led_red_sys; -+ led-running = &led_green_sys; -+ led-upgrade = &led_red_sys; -+ }; -+ -+ memory { -+ device_type = "memory"; -+ reg = <0x00000000 0x10000000>; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200"; -+ stdout-path = &uart0; -+ }; -+ -+ ocp@f1000000 { -+ pinctrl: pin-controller@10000 { -+ pinctrl-names = "default"; -+ -+ pmx_led_esata_green: pmx-led-esata-green { -+ marvell,pins = "mpp12"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_esata_red: pmx-led-esata-red { -+ marvell,pins = "mpp13"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_usb_green: pmx-led-usb-green { -+ marvell,pins = "mpp15"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_usb_red: pmx-led-usb-red { -+ marvell,pins = "mpp16"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_sys_green: pmx-led-sys-green { -+ marvell,pins = "mpp28"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_sys_red: pmx-led-sys-red { -+ marvell,pins = "mpp29"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_hdd_green: pmx-led-hdd-green { -+ marvell,pins = "mpp41"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_hdd_red: pmx-led-hdd-red { -+ marvell,pins = "mpp42"; -+ marvell,function = "gpio"; -+ }; -+ -+ }; -+ -+ i2c@11000 { -+ status = "okay"; -+ -+ lm85: lm85@2e { -+ compatible = "national,lm85"; -+ reg = <0x2e>; -+ }; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ led_green_sys: green-sys { -+ label = "nsa310:green:sys"; -+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; -+ default-state = "on"; -+ }; -+ led_red_sys: red-sys { -+ label = "nsa310:red:sys"; -+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; -+ }; -+ green-hdd { -+ label = "nsa310:green:hdd"; -+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; -+ }; -+ red-hdd { -+ label = "nsa310:red:hdd"; -+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; -+ }; -+ green-esata { -+ label = "nsa310:green:esata"; -+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; -+ }; -+ red-esata { -+ label = "nsa310:red:esata"; -+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; -+ }; -+ green-usb { -+ label = "nsa310:green:usb"; -+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; -+ }; -+ red-usb { -+ label = "nsa310:red:usb"; -+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; -+ }; -+ green-copy { -+ label = "nsa310:green:copy"; -+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; -+ }; -+ red-copy { -+ label = "nsa310:red:copy"; -+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+}; diff --git a/target/linux/kirkwood/patches-4.14/108-on100.patch b/target/linux/kirkwood/patches-4.14/108-on100.patch deleted file mode 100644 index 78f2f4a3fe..0000000000 --- a/target/linux/kirkwood/patches-4.14/108-on100.patch +++ /dev/null @@ -1,178 +0,0 @@ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-on100.dts -@@ -0,0 +1,165 @@ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6282.dtsi" -+ -+/ { -+ model = "Cisco Systems ON100"; -+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; -+ -+ memory { -+ device_type = "memory"; -+ reg = <0x00000000 0x20000000>; -+ }; -+ -+ aliases { -+ led-boot = &led_health_green; -+ led-failsafe = &led_health_red; -+ led-running = &led_health_green; -+ led-upgrade = &led_health_red; -+ serial0 = &uart0; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200n8 earlyprintk"; -+ stdout-path = "serial0:115200n8"; -+ }; -+ -+ gpio_keys { -+ compatible = "gpio-keys"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ pinctrl-0 = <&pmx_btn_reset>; -+ pinctrl-names = "default"; -+ -+ button@1 { -+ label = "Reset Button"; -+ linux,code = <KEY_RESTART>; -+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; -+ pinctrl-names = "default"; -+ -+ led_health_green: health_green { -+ label = "on100:green:health"; -+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; -+ default-state = "on"; -+ }; -+ -+ led_health_red: health_red { -+ label = "on100:red:health"; -+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; -+ }; -+ -+ health2_green { -+ label = "on100:green:health2"; -+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; -+ }; -+ -+ health2_red { -+ label = "on100:red:health2"; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+}; -+ -+ð0 { -+ status = "okay"; -+ -+ ethernet0-port@0 { -+ phy-handle = <ðphy0>; -+ phy-connection-type = "rgmii-id"; -+ }; -+}; -+ -+ð1 { -+ status = "okay"; -+ -+ ethernet1-port@0 { -+ phy-handle = <ðphy1>; -+ phy-connection-type = "rgmii-id"; -+ }; -+}; -+ -+&mdio { -+ status = "okay"; -+ -+ ethphy0: ethernet-phy@0 { -+ /* Marvell 88E1121R */ -+ compatible = "ethernet-phy-id0141.0cb0", -+ "ethernet-phy-ieee802.3-c22"; -+ reg = <0>; -+ }; -+ -+ ethphy1: ethernet-phy@1 { -+ /* Marvell 88E1121R */ -+ compatible = "ethernet-phy-id0141.0cb0", -+ "ethernet-phy-ieee802.3-c22"; -+ reg = <1>; -+ }; -+}; -+ -+&nand { -+ status = "okay"; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x00000000 0x000a0000>; -+ read-only; -+ }; -+ -+ partition@a0000 { -+ label = "u-boot environment"; -+ reg = <0x000a0000 0x00020000>; -+ read-only; -+ }; -+ -+ partition@c0000 { -+ label = "kernel"; -+ reg = <0x000c0000 0x00540000>; -+ }; -+ -+ partition@600000 { -+ label = "ubi"; -+ reg = <0x00600000 0x1fa00000>; -+ }; -+}; -+ -+&pinctrl { -+ pmx_led_health_r: pmx-led-health-r { -+ marvell,pins = "mpp45"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health_g: pmx-led-health-g { -+ marvell,pins = "mpp44"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health2_r: pmx-led-health2-r { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health2_g: pmx-led-health2-g { -+ marvell,pins = "mpp46"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_btn_reset: pmx-led-reset { -+ marvell,pins = "mpp31"; -+ marvell,function = "gpio"; -+ }; -+}; -+ -+&sdio { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -271,6 +271,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-nsa310b.dtb \ - kirkwood-nsa320.dtb \ - kirkwood-nsa325.dtb \ -+ kirkwood-on100.dtb \ - kirkwood-openblocks_a6.dtb \ - kirkwood-openblocks_a7.dtb \ - kirkwood-openrd-base.dtb \ diff --git a/target/linux/kirkwood/patches-4.19/104-ea3500.patch b/target/linux/kirkwood/patches-4.19/104-ea3500.patch deleted file mode 100644 index 04a919e072..0000000000 --- a/target/linux/kirkwood/patches-4.19/104-ea3500.patch +++ /dev/null @@ -1,264 +0,0 @@ ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -269,6 +269,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-linkstation-lswsxl.dtb \ - kirkwood-linkstation-lswvl.dtb \ - kirkwood-linkstation-lswxl.dtb \ -+ kirkwood-linksys-audi.dtb \ - kirkwood-linksys-viper.dtb \ - kirkwood-lschlv2.dtb \ - kirkwood-lsxhl.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-linksys-audi.dts -@@ -0,0 +1,251 @@ -+// SPDX-License-Identifier: GPL-2.0 -+/* -+ * kirkwood-linksys-audi.dts - Device Tree file for Linksys EA3500 -+ * -+ * (c) 2013 Jonas Gorski <jogo@openwrt.org> -+ * (c) 2013 Deutsche Telekom Innovation Laboratories -+ * (c) 2014 Luka Perkov <luka@openwrt.org> -+ * (c) 2014 Dan Walters <dan@walters.io> -+ * -+ */ -+ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6282.dtsi" -+ -+/ { -+ model = "Linksys Audi (EA3500)"; -+ compatible = "linksys,audi", "marvell,kirkwood-88f6282", "marvell,kirkwood"; -+ -+ memory@0 { -+ device_type = "memory"; -+ reg = <0x00000000 0x4000000>; -+ }; -+ -+ aliases { -+ led-boot = &led_power; -+ led-failsafe = &led_power; -+ led-running = &led_power; -+ led-upgrade = &led_power; -+ serial0 = &uart0; -+ }; -+ -+ chosen { -+ stdout-path = "serial0:115200n8"; -+ }; -+ -+ gpio_keys { -+ compatible = "gpio-keys"; -+ pinctrl-0 = < &pmx_btn_wps &pmx_btn_reset >; -+ pinctrl-names = "default"; -+ -+ wps { -+ label = "WPS Button"; -+ linux,code = <KEY_WPS_BUTTON>; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ -+ reset { -+ label = "Reset Button"; -+ linux,code = <KEY_RESTART>; -+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ pinctrl-0 = < &pmx_led_green_power >; -+ pinctrl-names = "default"; -+ -+ led_power: power { -+ label = "audi:green:power"; -+ gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; -+ default-state = "on"; -+ }; -+ }; -+ -+ switches { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ -+ mvsw61xx@10 { -+ compatible = "marvell,88e6171"; -+ status = "okay"; -+ reg = <0x10>; -+ -+ mii-bus = <&mdio>; -+ cpu-port-0 = <5>; -+ cpu-port-1 = <6>; -+ is-indirect; -+ }; -+ }; -+ -+ dsa { -+ compatible = "marvell,dsa"; -+ #address-cells = <2>; -+ #size-cells = <0>; -+ -+ dsa,ethernet = <ð0port>; -+ dsa,mii-bus = <&mdio>; -+ -+ switch@16,0 { -+ #address-cells = <1>; -+ #size-cells = <0>; -+ reg = <16 0>; /* MDIO address 16, switch 0 in tree */ -+ -+ port@0 { -+ reg = <0>; -+ label = "ethernet1"; -+ }; -+ -+ port@1 { -+ reg = <1>; -+ label = "ethernet2"; -+ }; -+ -+ port@2 { -+ reg = <2>; -+ label = "ethernet3"; -+ }; -+ -+ port@3 { -+ reg = <3>; -+ label = "ethernet4"; -+ }; -+ -+ port@4 { -+ reg = <4>; -+ label = "internet"; -+ }; -+ -+ port@5 { -+ reg = <5>; -+ label = "cpu"; -+ }; -+ }; -+ }; -+}; -+ -+&pinctrl { -+ pmx_led_green_power: pmx-led-green-power { -+ marvell,pins = "mpp7"; -+ marvell,function = "gpo"; -+ }; -+ pmx_btn_wps: pmx-btn-wps { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ pmx_btn_reset: pmx-btn-reset { -+ marvell,pins = "mpp48"; -+ marvell,function = "gpio"; -+ }; -+}; -+ -+&nand { -+ status = "okay"; -+ pinctrl-0 = <&pmx_nand>; -+ pinctrl-names = "default"; -+ -+ partitions { -+ compatible = "fixed-partitions"; -+ #address-cells = <1>; -+ #size-cells = <1>; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x0 0x80000>; -+ read-only; -+ }; -+ -+ partition@80000 { -+ label = "u_env"; -+ reg = <0x80000 0x4000>; -+ }; -+ -+ partition@84000 { -+ label = "s_env"; -+ reg = <0x84000 0x4000>; -+ }; -+ -+ partition@200000 { -+ label = "kernel1"; -+ reg = <0x200000 0x290000>; -+ }; -+ -+ partition@490000 { -+ label = "rootfs1"; -+ reg = <0x490000 0x1170000>; -+ }; -+ -+ partition@1600000 { -+ label = "kernel2"; -+ reg = <0x1600000 0x290000>; -+ }; -+ -+ partition@1890000 { -+ label = "rootfs2"; -+ reg = <0x1890000 0x1170000>; -+ }; -+ -+ partition@2a00000 { -+ label = "syscfg"; -+ reg = <0x2a00000 0x1600000>; -+ }; -+ -+ partition@88000 { -+ label = "unused"; -+ reg = <0x88000 0x178000>; -+ }; -+ -+ }; -+}; -+ -+&pciec { -+ status = "okay"; -+}; -+ -+&pcie0 { -+ status = "okay"; -+}; -+ -+&pcie1 { -+ status = "okay"; -+}; -+ -+&mdio { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; -+ -+/* eth0 is connected to a Marvell 88E6171 switch, without a PHY. So set -+ * fixed speed and duplex. -+ */ -+ð0 { -+ status = "okay"; -+ ethernet0-port@0 { -+ speed = <1000>; -+ duplex = <1>; -+ }; -+}; -+ -+/* eth1 is connected to the switch at port 6. However DSA only supports a -+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion. -+ */ -+ð1 { -+ status = "okay"; -+ ethernet1-port@0 { -+ speed = <1000>; -+ duplex = <1>; -+ }; -+}; -+ -+/* There is no battery on the board, so the RTC does not keep -+ * time when there is no power, making it useless. -+ */ -+&rtc { -+ status = "disabled"; -+}; diff --git a/target/linux/kirkwood/patches-4.19/105-goflexhome.patch b/target/linux/kirkwood/patches-4.19/105-goflexhome.patch deleted file mode 100644 index cca65f2141..0000000000 --- a/target/linux/kirkwood/patches-4.19/105-goflexhome.patch +++ /dev/null @@ -1,137 +0,0 @@ ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -256,6 +256,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-ds411.dtb \ - kirkwood-ds411j.dtb \ - kirkwood-ds411slim.dtb \ -+ kirkwood-goflexhome.dtb \ - kirkwood-goflexnet.dtb \ - kirkwood-guruplug-server-plus.dtb \ - kirkwood-ib62x0.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-goflexhome.dts -@@ -0,0 +1,124 @@ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6281.dtsi" -+ -+/ { -+ model = "Seagate GoFlex Home"; -+ compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood"; -+ -+ aliases { -+ led-boot = &led_health; -+ led-failsafe = &led_fault; -+ led-running = &led_health; -+ led-upgrade = &led_fault; -+ }; -+ -+ memory@0 { -+ device_type = "memory"; -+ reg = <0x00000000 0x8000000>; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10"; -+ stdout-path = &uart0; -+ }; -+ -+ ocp@f1000000 { -+ pinctrl: pin-controller@10000 { -+ pmx_usb_power_enable: pmx-usb-power-enable { -+ marvell,pins = "mpp29"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_white: pmx-led-white { -+ marvell,pins = "mpp40"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_green: pmx-led_green { -+ marvell,pins = "mpp46"; -+ marvell,function = "gpio"; -+ }; -+ pmx_led_orange: pmx-led-orange { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ }; -+ serial@12000 { -+ status = "ok"; -+ }; -+ -+ sata@80000 { -+ status = "okay"; -+ nr-ports = <2>; -+ }; -+ -+ }; -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ led_health: health { -+ label = "status:green:health"; -+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; -+ default-state = "on"; -+ }; -+ led_fault: fault { -+ label = "status:orange:fault"; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ misc { -+ label = "status:white:misc"; -+ gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; -+ linux,default-trigger = "disk-activity"; -+ }; -+ }; -+ regulators { -+ compatible = "simple-bus"; -+ #address-cells = <1>; -+ #size-cells = <0>; -+ pinctrl-0 = <&pmx_usb_power_enable>; -+ pinctrl-names = "default"; -+ -+ usb_power: regulator@1 { -+ compatible = "regulator-fixed"; -+ reg = <1>; -+ regulator-name = "USB Power"; -+ regulator-min-microvolt = <5000000>; -+ regulator-max-microvolt = <5000000>; -+ enable-active-high; -+ regulator-always-on; -+ regulator-boot-on; -+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+}; -+ -+&nand { -+ chip-delay = <40>; -+ status = "okay"; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x0000000 0x100000>; -+ read-only; -+ }; -+ -+ partition@100000 { -+ label = "ubi"; -+ reg = <0x100000 0x0ff00000>; -+ }; -+}; -+ -+&mdio { -+ status = "okay"; -+ -+ ethphy0: ethernet-phy@0 { -+ reg = <0>; -+ }; -+}; -+ -+ð0 { -+ status = "okay"; -+ ethernet0-port@0 { -+ phy-handle = <ðphy0>; -+ }; -+}; diff --git a/target/linux/kirkwood/patches-4.19/107-02-nsa310b.patch b/target/linux/kirkwood/patches-4.19/107-02-nsa310b.patch deleted file mode 100644 index ba2ae7d2de..0000000000 --- a/target/linux/kirkwood/patches-4.19/107-02-nsa310b.patch +++ /dev/null @@ -1,155 +0,0 @@ -kirkwood: add nsa310b dtb, a zyxel nsa310 variant - -add support to a nsa310 variant with red/green usb led -and lm85 temp/fan controller - -Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> - -NOTE: this patch can be upstreamed as-is, LEDE-specific - nand partitions are set in another patch - ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -287,6 +287,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-ns2mini.dtb \ - kirkwood-nsa310.dtb \ - kirkwood-nsa310a.dtb \ -+ kirkwood-nsa310b.dtb \ - kirkwood-nsa320.dtb \ - kirkwood-nsa325.dtb \ - kirkwood-openblocks_a6.dtb \ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-nsa310b.dts -@@ -0,0 +1,132 @@ -+/dts-v1/; -+ -+#include "kirkwood-nsa3x0-common.dtsi" -+ -+/* -+ * There are at least two different NSA310 designs. This variant has -+ * a red/green USB Led (same as nsa310) and a lm85 temp/fan controller. -+ */ -+ -+/ { -+ model = "ZyXEL NSA310b"; -+ compatible = "zyxel,nsa310b", "zyxel,nsa310", "marvell,kirkwood-88f6281", "marvell,kirkwood"; -+ -+ aliases { -+ led-boot = &led_green_sys; -+ led-failsafe = &led_red_sys; -+ led-running = &led_green_sys; -+ led-upgrade = &led_red_sys; -+ }; -+ -+ memory@0 { -+ device_type = "memory"; -+ reg = <0x00000000 0x10000000>; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200"; -+ stdout-path = &uart0; -+ }; -+ -+ ocp@f1000000 { -+ pinctrl: pin-controller@10000 { -+ pinctrl-names = "default"; -+ -+ pmx_led_esata_green: pmx-led-esata-green { -+ marvell,pins = "mpp12"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_esata_red: pmx-led-esata-red { -+ marvell,pins = "mpp13"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_usb_green: pmx-led-usb-green { -+ marvell,pins = "mpp15"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_usb_red: pmx-led-usb-red { -+ marvell,pins = "mpp16"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_sys_green: pmx-led-sys-green { -+ marvell,pins = "mpp28"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_sys_red: pmx-led-sys-red { -+ marvell,pins = "mpp29"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_hdd_green: pmx-led-hdd-green { -+ marvell,pins = "mpp41"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_hdd_red: pmx-led-hdd-red { -+ marvell,pins = "mpp42"; -+ marvell,function = "gpio"; -+ }; -+ -+ }; -+ -+ i2c@11000 { -+ status = "okay"; -+ -+ lm85: lm85@2e { -+ compatible = "national,lm85"; -+ reg = <0x2e>; -+ }; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ -+ led_green_sys: green-sys { -+ label = "nsa310:green:sys"; -+ gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; -+ default-state = "on"; -+ }; -+ led_red_sys: red-sys { -+ label = "nsa310:red:sys"; -+ gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>; -+ }; -+ green-hdd { -+ label = "nsa310:green:hdd"; -+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; -+ }; -+ red-hdd { -+ label = "nsa310:red:hdd"; -+ gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; -+ }; -+ green-esata { -+ label = "nsa310:green:esata"; -+ gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; -+ }; -+ red-esata { -+ label = "nsa310:red:esata"; -+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; -+ }; -+ green-usb { -+ label = "nsa310:green:usb"; -+ gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; -+ }; -+ red-usb { -+ label = "nsa310:red:usb"; -+ gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; -+ }; -+ green-copy { -+ label = "nsa310:green:copy"; -+ gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; -+ }; -+ red-copy { -+ label = "nsa310:red:copy"; -+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; -+ }; -+ }; -+}; diff --git a/target/linux/kirkwood/patches-4.19/108-on100.patch b/target/linux/kirkwood/patches-4.19/108-on100.patch deleted file mode 100644 index bc0916f161..0000000000 --- a/target/linux/kirkwood/patches-4.19/108-on100.patch +++ /dev/null @@ -1,176 +0,0 @@ ---- /dev/null -+++ b/arch/arm/boot/dts/kirkwood-on100.dts -@@ -0,0 +1,163 @@ -+/dts-v1/; -+ -+#include "kirkwood.dtsi" -+#include "kirkwood-6282.dtsi" -+ -+/ { -+ model = "Cisco Systems ON100"; -+ compatible = "cisco,on100", "marvell,kirkwood-88f6282", "marvell,kirkwood"; -+ -+ memory@0 { -+ device_type = "memory"; -+ reg = <0x00000000 0x20000000>; -+ }; -+ -+ aliases { -+ led-boot = &led_health_green; -+ led-failsafe = &led_health_red; -+ led-running = &led_health_green; -+ led-upgrade = &led_health_red; -+ serial0 = &uart0; -+ }; -+ -+ chosen { -+ bootargs = "console=ttyS0,115200n8 earlyprintk"; -+ stdout-path = "serial0:115200n8"; -+ }; -+ -+ gpio_keys { -+ compatible = "gpio-keys"; -+ pinctrl-0 = <&pmx_btn_reset>; -+ pinctrl-names = "default"; -+ -+ reset { -+ label = "Reset Button"; -+ linux,code = <KEY_RESTART>; -+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+ -+ gpio-leds { -+ compatible = "gpio-leds"; -+ pinctrl-0 = < &pmx_led_health_r &pmx_led_health_g >; -+ pinctrl-names = "default"; -+ -+ led_health_green: health_green { -+ label = "on100:green:health"; -+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; -+ default-state = "on"; -+ }; -+ -+ led_health_red: health_red { -+ label = "on100:red:health"; -+ gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; -+ }; -+ -+ health2_green { -+ label = "on100:green:health2"; -+ gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; -+ }; -+ -+ health2_red { -+ label = "on100:red:health2"; -+ gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; -+ }; -+ }; -+}; -+ -+ð0 { -+ status = "okay"; -+ -+ ethernet0-port@0 { -+ phy-handle = <ðphy0>; -+ phy-connection-type = "rgmii-id"; -+ }; -+}; -+ -+ð1 { -+ status = "okay"; -+ -+ ethernet1-port@0 { -+ phy-handle = <ðphy1>; -+ phy-connection-type = "rgmii-id"; -+ }; -+}; -+ -+&mdio { -+ status = "okay"; -+ -+ ethphy0: ethernet-phy@0 { -+ /* Marvell 88E1121R */ -+ compatible = "ethernet-phy-id0141.0cb0", -+ "ethernet-phy-ieee802.3-c22"; -+ reg = <0>; -+ }; -+ -+ ethphy1: ethernet-phy@1 { -+ /* Marvell 88E1121R */ -+ compatible = "ethernet-phy-id0141.0cb0", -+ "ethernet-phy-ieee802.3-c22"; -+ reg = <1>; -+ }; -+}; -+ -+&nand { -+ status = "okay"; -+ -+ partition@0 { -+ label = "u-boot"; -+ reg = <0x00000000 0x000a0000>; -+ read-only; -+ }; -+ -+ partition@a0000 { -+ label = "u-boot environment"; -+ reg = <0x000a0000 0x00020000>; -+ read-only; -+ }; -+ -+ partition@c0000 { -+ label = "kernel"; -+ reg = <0x000c0000 0x00540000>; -+ }; -+ -+ partition@600000 { -+ label = "ubi"; -+ reg = <0x00600000 0x1fa00000>; -+ }; -+}; -+ -+&pinctrl { -+ pmx_led_health_r: pmx-led-health-r { -+ marvell,pins = "mpp45"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health_g: pmx-led-health-g { -+ marvell,pins = "mpp44"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health2_r: pmx-led-health2-r { -+ marvell,pins = "mpp47"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_led_health2_g: pmx-led-health2-g { -+ marvell,pins = "mpp46"; -+ marvell,function = "gpio"; -+ }; -+ -+ pmx_btn_reset: pmx-led-reset { -+ marvell,pins = "mpp31"; -+ marvell,function = "gpio"; -+ }; -+}; -+ -+&sdio { -+ status = "okay"; -+}; -+ -+&uart0 { -+ status = "okay"; -+}; ---- a/arch/arm/boot/dts/Makefile -+++ b/arch/arm/boot/dts/Makefile -@@ -290,6 +290,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \ - kirkwood-nsa310b.dtb \ - kirkwood-nsa320.dtb \ - kirkwood-nsa325.dtb \ -+ kirkwood-on100.dtb \ - kirkwood-openblocks_a6.dtb \ - kirkwood-openblocks_a7.dtb \ - kirkwood-openrd-base.dtb \ |