add support for board named RTA770W

Actually this board is the very same as the rta770bw,
where the additional 'b' within the name just
indicates 'Annex B'. The ADSL Modem itself is able
to handle both, Annex A as well as Annex B -
the loaded firmware makes the only difference

SVN-Revision: 35500

4 files changed, 215 insertions, 1 deletions

diff --git a/target/linux/brcm63xx/base-files/etc/uci-defaults/02_network b/target/linux/brcm63xx/base-files/etc/uci-defaults/02_network
index 106bf5f86f..f59fed6781 100755
--- a/target/linux/brcm63xx/base-files/etc/uci-defaults/02_network
+++ b/target/linux/brcm63xx/base-files/etc/uci-defaults/02_network
@@ -14,6 +14,8 @@ ucidef_set_interface_loopback
 
 case "$board_name" in
 
+RTA770BW |\
+RTA770W |\
 96348W3 |\
 96358-502V |\
 SPW500V)
@@ -31,7 +33,6 @@ CT6373-1 |\
 D-4P-W |\
 "F@ST2604" |\
 RTA1320_16M |\
-RTA770BW |\
 V2110)
 	ucidef_set_interface_lan "eth0"
 	ucidef_add_switch "eth0" "1" "1"
diff --git a/target/linux/brcm63xx/patches-3.6/556-board_rta770w.patch b/target/linux/brcm63xx/patches-3.6/556-board_rta770w.patch
new file mode 100644
index 0000000000..e0eedad1e7
--- /dev/null
+++ b/target/linux/brcm63xx/patches-3.6/556-board_rta770w.patch
@@ -0,0 +1,71 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -796,6 +796,60 @@
+ 		},
+ 	},
+ };
++
++// Actually this board is the very same as the rta770bw,
++// where the additional 'b' within the name just
++// just indicates 'Annex B'. The ADSL Modem itself is able
++// to handle both Annex A as well as Annex B -
++// the loaded firmware makes the only difference
++static struct board_info __initdata board_rta770w = {
++	.name				= "RTA770W",
++	.expected_cpu_id		= 0x6345,
++
++	.has_uart0			= 1,
++
++	.has_enet0			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "RTA770W:green:usb",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++		{
++			.name		= "RTA770W:green:adsl",
++			.gpio		= 8,
++		},
++		{
++			.name		= "RTA770W:green:diag",
++			.gpio		= 10,
++			.active_low	= 1,
++		},
++		{
++			.name		= "RTA770W:green:wlan",
++			.gpio		= 11,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 13,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -3750,6 +3804,7 @@
+ #ifdef CONFIG_BCM63XX_CPU_6345
+ 	&board_96345gw2,
+ 	&board_rta770bw,
++	&board_rta770w,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6348
+ 	&board_96348r,
diff --git a/target/linux/brcm63xx/patches-3.7/556-board_rta770w.patch b/target/linux/brcm63xx/patches-3.7/556-board_rta770w.patch
new file mode 100644
index 0000000000..e0eedad1e7
--- /dev/null
+++ b/target/linux/brcm63xx/patches-3.7/556-board_rta770w.patch
@@ -0,0 +1,71 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -796,6 +796,60 @@
+ 		},
+ 	},
+ };
++
++// Actually this board is the very same as the rta770bw,
++// where the additional 'b' within the name just
++// just indicates 'Annex B'. The ADSL Modem itself is able
++// to handle both Annex A as well as Annex B -
++// the loaded firmware makes the only difference
++static struct board_info __initdata board_rta770w = {
++	.name				= "RTA770W",
++	.expected_cpu_id		= 0x6345,
++
++	.has_uart0			= 1,
++
++	.has_enet0			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "RTA770W:green:usb",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++		{
++			.name		= "RTA770W:green:adsl",
++			.gpio		= 8,
++		},
++		{
++			.name		= "RTA770W:green:diag",
++			.gpio		= 10,
++			.active_low	= 1,
++		},
++		{
++			.name		= "RTA770W:green:wlan",
++			.gpio		= 11,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 13,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -3750,6 +3804,7 @@
+ #ifdef CONFIG_BCM63XX_CPU_6345
+ 	&board_96345gw2,
+ 	&board_rta770bw,
++	&board_rta770w,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6348
+ 	&board_96348r,
diff --git a/target/linux/brcm63xx/patches-3.8/556-board_rta770w.patch b/target/linux/brcm63xx/patches-3.8/556-board_rta770w.patch
new file mode 100644
index 0000000000..e0eedad1e7
--- /dev/null
+++ b/target/linux/brcm63xx/patches-3.8/556-board_rta770w.patch
@@ -0,0 +1,71 @@
+--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
+@@ -796,6 +796,60 @@
+ 		},
+ 	},
+ };
++
++// Actually this board is the very same as the rta770bw,
++// where the additional 'b' within the name just
++// just indicates 'Annex B'. The ADSL Modem itself is able
++// to handle both Annex A as well as Annex B -
++// the loaded firmware makes the only difference
++static struct board_info __initdata board_rta770w = {
++	.name				= "RTA770W",
++	.expected_cpu_id		= 0x6345,
++
++	.has_uart0			= 1,
++
++	.has_enet0			= 1,
++
++	.enet0 = {
++		.has_phy		= 1,
++		.phy_id			= 0,
++		.force_speed_100	= 1,
++		.force_duplex_full	= 1,
++	},
++
++	.leds = {
++		{
++			.name		= "RTA770W:green:usb",
++			.gpio		= 7,
++			.active_low	= 1,
++		},
++		{
++			.name		= "RTA770W:green:adsl",
++			.gpio		= 8,
++		},
++		{
++			.name		= "RTA770W:green:diag",
++			.gpio		= 10,
++			.active_low	= 1,
++		},
++		{
++			.name		= "RTA770W:green:wlan",
++			.gpio		= 11,
++			.active_low	= 1,
++		},
++	},
++
++	.buttons = {
++		{
++			.desc		= "reset",
++			.gpio		= 13,
++			.type		= EV_KEY,
++			.code		= KEY_RESTART,
++			.active_low	= 1,
++			.debounce_interval = BCM963XX_KEYS_DEBOUNCE_INTERVAL,
++		},
++	},
++};
+ #endif
+ 
+ /*
+@@ -3750,6 +3804,7 @@
+ #ifdef CONFIG_BCM63XX_CPU_6345
+ 	&board_96345gw2,
+ 	&board_rta770bw,
++	&board_rta770w,
+ #endif
+ #ifdef CONFIG_BCM63XX_CPU_6348
+ 	&board_96348r,