ipq40xx: add support for 8devices Habanero DVK

This patch adds support for the 8devices Habanero development board.

Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18

2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration

Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.

Signed-off-by: Robert Marko <robimarko@gmail.com>

8 files changed, 763 insertions, 2 deletions

diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network
index fb41572e37..44cb9f9d12 100755
--- a/target/linux/ipq40xx/base-files/etc/board.d/02_network
+++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network
@@ -12,6 +12,7 @@ ipq40xx_setup_interfaces()
 	local board="$1"
 
 	case "$board" in
+	8dev,habanero-dvk|\
 	8dev,jalapeno|\
 	alfa-network,ap120c-ac|\
 	engenius,ens620ext)
@@ -97,6 +98,9 @@ ipq40xx_setup_macs()
 	local label_mac=""
 
 	case "$board" in
+	8dev,habanero-dvk)
+		label_mac=$(mtd_get_mac_binary "ART" 0x1006)
+		;;
 	asus,rt-ac58u)
 		CI_UBIPART=UBI_DEV
 		wan_mac=$(mtd_get_mac_binary_ubi Factory 0x1006)
diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 50bfbb0a86..c65fa30474 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -44,6 +44,7 @@ case "$FIRMWARE" in
 	;;
 "ath10k/pre-cal-ahb-a000000.wifi.bin")
 	case "$board" in
+	8dev,habanero-dvk |\
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	cilab,meshpoint-one |\
@@ -124,6 +125,7 @@ case "$FIRMWARE" in
 	;;
 "ath10k/pre-cal-ahb-a800000.wifi.bin")
 	case "$board" in
+	8dev,habanero-dvk |\
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	cilab,meshpoint-one |\
diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts
new file mode 100644
index 0000000000..8fe7644a9b
--- /dev/null
+++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts
@@ -0,0 +1,357 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2019, Robert Marko <robimarko@gmail.com> */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "8devices Habanero DVK";
+	compatible = "8dev,habanero-dvk";
+
+	aliases {
+		led-boot = &led_status;
+		led-failsafe = &led_status;
+		led-running = &led_status;
+		led-upgrade = &led_upgrade;
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+
+			pinctrl-0 = <&mdio_pins>;
+			pinctrl-names = "default";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		counter@4a1000 {
+			compatible = "qcom,qca-gcnt";
+			reg = <0x4a1000 0x4>;
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			status = "okay";
+
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		usb2: usb2@60f8800 {
+			status = "okay";
+		};
+
+		usb3: usb3@8af8800 {
+			status = "okay";
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status: status {
+			label = "habanero-dvk:green:status";
+			gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+
+		led_upgrade: upgrade {
+			label = "habanero-dvk:green:upgrade";
+			gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "habanero-dvk:green:wlan2g";
+			gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan5g {
+			label = "habanero-dvk:green:wlan5g";
+			gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+};
+
+&vqmmc {
+	status = "okay";
+};
+
+&sdhci {
+	status = "okay";
+
+	pinctrl-0 = <&sd_pins>;
+	pinctrl-names = "default";
+	cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
+	vqmmc-supply = <&vqmmc>;
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&tlmm {
+	mdio_pins: mdio_pinmux {
+		mux_1 {
+			pins = "gpio6";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_2 {
+			pins = "gpio7";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio13", "gpio14", "gpio15";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio12";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	nand_pins: nand_pins {
+		pullups {
+			pins =  "gpio52", "gpio53", "gpio58", "gpio59";
+			function = "qpic";
+			bias-pull-up;
+		};
+
+		pulldowns {
+			pins = "gpio54", "gpio55", "gpio56", "gpio57",
+				"gpio60", "gpio62", "gpio63", "gpio64",
+				"gpio65", "gpio66", "gpio67", "gpio68",
+				"gpio69";
+			function = "qpic";
+			bias-pull-down;
+		};
+	};
+
+	sd_pins: sd_pins {
+		pinmux {
+			function = "sdio";
+			pins = "gpio23", "gpio24", "gpio25", "gpio26",
+				"gpio28", "gpio29", "gpio30", "gpio31";
+			drive-strength = <10>;
+		};
+
+		pinmux_sd_clk {
+			function = "sdio";
+			pins = "gpio27";
+			drive-strength = <16>;
+		};
+
+		pinmux_sd7 {
+			function = "sdio";
+			pins = "gpio32";
+			drive-strength = <10>;
+			bias-disable;
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <24000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+			partition@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+			partition@e0000 {
+				label = "APPSBLENV"; /* uboot env */
+				reg = <0x000e0000 0x00010000>;
+				read-only;
+			};
+			partition@f0000 {
+				label = "APPSBL"; /* uboot */
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+			partition@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+			partition@180000 {
+				label = "cfg";
+				reg = <0x00180000 0x00040000>;
+			};
+			partition@1c0000 {
+				label = "firmware";
+				compatible = "denx,fit";
+				reg = <0x001c0000 0x01e40000>;
+			};
+		};
+	};
+};
+
+/* Some DVK boards ship without NAND */
+&nand {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+
+	perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+	wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+	/* Free slot for use */
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+	};
+};
+
+&wifi0 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "8devices-Habanero";
+};
+
+&wifi1 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "8devices-Habanero";
+};
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
diff --git a/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts
new file mode 100644
index 0000000000..8fe7644a9b
--- /dev/null
+++ b/target/linux/ipq40xx/files-5.4/arch/arm/boot/dts/qcom-ipq4019-habanero-dvk.dts
@@ -0,0 +1,357 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/* Copyright (c) 2019, Robert Marko <robimarko@gmail.com> */
+
+#include "qcom-ipq4019.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/qcom,tcsr.h>
+
+/ {
+	model = "8devices Habanero DVK";
+	compatible = "8dev,habanero-dvk";
+
+	aliases {
+		led-boot = &led_status;
+		led-failsafe = &led_status;
+		led-running = &led_status;
+		led-upgrade = &led_upgrade;
+	};
+
+	soc {
+		rng@22000 {
+			status = "okay";
+		};
+
+		mdio@90000 {
+			status = "okay";
+
+			pinctrl-0 = <&mdio_pins>;
+			pinctrl-names = "default";
+		};
+
+		ess-psgmii@98000 {
+			status = "okay";
+		};
+
+		counter@4a1000 {
+			compatible = "qcom,qca-gcnt";
+			reg = <0x4a1000 0x4>;
+		};
+
+		tcsr@1949000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1949000 0x100>;
+			qcom,wifi_glb_cfg = <TCSR_WIFI_GLB_CFG>;
+		};
+
+		tcsr@194b000 {
+			status = "okay";
+
+			compatible = "qcom,tcsr";
+			reg = <0x194b000 0x100>;
+			qcom,usb-hsphy-mode-select = <TCSR_USB_HSPHY_HOST_MODE>;
+		};
+
+		ess_tcsr@1953000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1953000 0x1000>;
+			qcom,ess-interface-select = <TCSR_ESS_PSGMII>;
+		};
+
+		tcsr@1957000 {
+			compatible = "qcom,tcsr";
+			reg = <0x1957000 0x100>;
+			qcom,wifi_noc_memtype_m0_m2 = <TCSR_WIFI_NOC_MEMTYPE_M0_M2>;
+		};
+
+		usb2: usb2@60f8800 {
+			status = "okay";
+		};
+
+		usb3: usb3@8af8800 {
+			status = "okay";
+		};
+
+		crypto@8e3a000 {
+			status = "okay";
+		};
+
+		watchdog@b017000 {
+			status = "okay";
+		};
+
+		ess-switch@c000000 {
+			status = "okay";
+		};
+
+		edma@c080000 {
+			status = "okay";
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_status: status {
+			label = "habanero-dvk:green:status";
+			gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+
+		led_upgrade: upgrade {
+			label = "habanero-dvk:green:upgrade";
+			gpios = <&tlmm 40 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan2g {
+			label = "habanero-dvk:green:wlan2g";
+			gpios = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan5g {
+			label = "habanero-dvk:green:wlan5g";
+			gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy1tpt";
+		};
+	};
+};
+
+&vqmmc {
+	status = "okay";
+};
+
+&sdhci {
+	status = "okay";
+
+	pinctrl-0 = <&sd_pins>;
+	pinctrl-names = "default";
+	cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>;
+	vqmmc-supply = <&vqmmc>;
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&tlmm {
+	mdio_pins: mdio_pinmux {
+		mux_1 {
+			pins = "gpio6";
+			function = "mdio";
+			bias-pull-up;
+		};
+
+		mux_2 {
+			pins = "gpio7";
+			function = "mdc";
+			bias-pull-up;
+		};
+	};
+
+	serial_pins: serial_pinmux {
+		mux {
+			pins = "gpio16", "gpio17";
+			function = "blsp_uart0";
+			bias-disable;
+		};
+	};
+
+	spi_0_pins: spi_0_pinmux {
+		pinmux {
+			function = "blsp_spi0";
+			pins = "gpio13", "gpio14", "gpio15";
+			drive-strength = <12>;
+			bias-disable;
+		};
+
+		pinmux_cs {
+			function = "gpio";
+			pins = "gpio12";
+			drive-strength = <2>;
+			bias-disable;
+			output-high;
+		};
+	};
+
+	nand_pins: nand_pins {
+		pullups {
+			pins =  "gpio52", "gpio53", "gpio58", "gpio59";
+			function = "qpic";
+			bias-pull-up;
+		};
+
+		pulldowns {
+			pins = "gpio54", "gpio55", "gpio56", "gpio57",
+				"gpio60", "gpio62", "gpio63", "gpio64",
+				"gpio65", "gpio66", "gpio67", "gpio68",
+				"gpio69";
+			function = "qpic";
+			bias-pull-down;
+		};
+	};
+
+	sd_pins: sd_pins {
+		pinmux {
+			function = "sdio";
+			pins = "gpio23", "gpio24", "gpio25", "gpio26",
+				"gpio28", "gpio29", "gpio30", "gpio31";
+			drive-strength = <10>;
+		};
+
+		pinmux_sd_clk {
+			function = "sdio";
+			pins = "gpio27";
+			drive-strength = <16>;
+		};
+
+		pinmux_sd7 {
+			function = "sdio";
+			pins = "gpio32";
+			drive-strength = <10>;
+			bias-disable;
+		};
+	};
+};
+
+&blsp_dma {
+	status = "okay";
+};
+
+&blsp1_spi1 {
+	status = "okay";
+
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <24000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "SBL1";
+				reg = <0x00000000 0x00040000>;
+				read-only;
+			};
+			partition@40000 {
+				label = "MIBIB";
+				reg = <0x00040000 0x00020000>;
+				read-only;
+			};
+			partition@60000 {
+				label = "QSEE";
+				reg = <0x00060000 0x00060000>;
+				read-only;
+			};
+			partition@c0000 {
+				label = "CDT";
+				reg = <0x000c0000 0x00010000>;
+				read-only;
+			};
+			partition@d0000 {
+				label = "DDRPARAMS";
+				reg = <0x000d0000 0x00010000>;
+				read-only;
+			};
+			partition@e0000 {
+				label = "APPSBLENV"; /* uboot env */
+				reg = <0x000e0000 0x00010000>;
+				read-only;
+			};
+			partition@f0000 {
+				label = "APPSBL"; /* uboot */
+				reg = <0x000f0000 0x00080000>;
+				read-only;
+			};
+			partition@170000 {
+				label = "ART";
+				reg = <0x00170000 0x00010000>;
+				read-only;
+			};
+			partition@180000 {
+				label = "cfg";
+				reg = <0x00180000 0x00040000>;
+			};
+			partition@1c0000 {
+				label = "firmware";
+				compatible = "denx,fit";
+				reg = <0x001c0000 0x01e40000>;
+			};
+		};
+	};
+};
+
+/* Some DVK boards ship without NAND */
+&nand {
+	status = "okay";
+
+	pinctrl-0 = <&nand_pins>;
+	pinctrl-names = "default";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-0 = <&serial_pins>;
+	pinctrl-names = "default";
+};
+
+&cryptobam {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+
+	perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>;
+	wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>;
+
+	/* Free slot for use */
+	bridge@0,0 {
+		reg = <0x00000000 0 0 0 0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+	};
+};
+
+&wifi0 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "8devices-Habanero";
+};
+
+&wifi1 {
+	status = "okay";
+
+	qcom,ath10k-calibration-variant = "8devices-Habanero";
+};
+
+&usb3_ss_phy {
+	status = "okay";
+};
+
+&usb3_hs_phy {
+	status = "okay";
+};
+
+&usb2_hs_phy {
+	status = "okay";
+};
diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile
index 9ddcd17f1d..8097bf439a 100644
--- a/target/linux/ipq40xx/image/Makefile
+++ b/target/linux/ipq40xx/image/Makefile
@@ -71,6 +71,18 @@ define Build/wrgg-image
 	mv $@.new $@
 endef
 
+define Device/8dev_habanero-dvk
+	$(call Device/FitImageLzma)
+	DEVICE_VENDOR := 8devices
+	DEVICE_MODEL := Habanero DVK
+	IMAGE_SIZE := 30976k
+	SOC := qcom-ipq4019
+	DEVICE_PACKAGES := ipq-wifi-8dev_habanero-dvk
+	IMAGES := sysupgrade.bin
+	IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += 8dev_habanero-dvk
+
 define Device/8dev_jalapeno-common
 	$(call Device/FitImage)
 	$(call Device/UbiFit)
diff --git a/target/linux/ipq40xx/patches-4.19/087-v5.6-mtd-spi-nor-Add-4B_OPCODES-flag-to-w25q256.patch b/target/linux/ipq40xx/patches-4.19/087-v5.6-mtd-spi-nor-Add-4B_OPCODES-flag-to-w25q256.patch
new file mode 100644
index 0000000000..03fae840cd
--- /dev/null
+++ b/target/linux/ipq40xx/patches-4.19/087-v5.6-mtd-spi-nor-Add-4B_OPCODES-flag-to-w25q256.patch
@@ -0,0 +1,27 @@
+From 10050a02f7d508fa88f70fcfceefbacd13488ca7 Mon Sep 17 00:00:00 2001
+From: Robert Marko <robimarko@gmail.com>
+Date: Mon, 23 Dec 2019 17:05:49 +0200
+Subject: [PATCH] mtd: spi-nor: Add 4B_OPCODES flag to w25q256
+
+The w25q256 supports 4-byte opcodes so lets add the flag.
+Tested on OpenWrt under 4.19.82 kernel on 8devices Habanero.
+
+Signed-off-by: Robert Marko <robimarko@gmail.com>
+Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
+---
+ drivers/mtd/spi-nor/spi-nor.c | 4 +++-
+ 1 file changed, 3 insertions(+), 1 deletion(-)
+
+--- a/drivers/mtd/spi-nor/spi-nor.c
++++ b/drivers/mtd/spi-nor/spi-nor.c
+@@ -1252,7 +1252,9 @@ static const struct flash_info spi_nor_i
+ 	{ "w25q80", INFO(0xef5014, 0, 64 * 1024,  16, SECT_4K) },
+ 	{ "w25q80bl", INFO(0xef4014, 0, 64 * 1024,  16, SECT_4K) },
+ 	{ "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) },
+-	{ "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
++	{ "w25q256", INFO(0xef4019, 0, 64 * 1024, 512,
++			  SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
++			  SPI_NOR_4B_OPCODES) },
+ 	{ "w25m512jv", INFO(0xef7119, 0, 64 * 1024, 1024,
+ 			SECT_4K | SPI_NOR_QUAD_READ | SPI_NOR_DUAL_READ) },
+ 
diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
index 89e665db23..81e33b15a9 100644
--- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -785,11 +785,43 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -785,11 +785,44 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -41,6 +41,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4019-fritzrepeater-1200.dtb \
 +	qcom-ipq4019-fritzrepeater-3000.dtb \
 +	qcom-ipq4019-ea8300.dtb \
++	qcom-ipq4019-habanero-dvk.dtb \
 +	qcom-ipq4019-map-ac2200.dtb \
 +	qcom-ipq4019-e2600ac-c1.dtb \
 +	qcom-ipq4019-e2600ac-c2.dtb \
diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
index d49c03c1d0..a63f0da85d 100644
--- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
+++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch
@@ -10,7 +10,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 
 --- a/arch/arm/boot/dts/Makefile
 +++ b/arch/arm/boot/dts/Makefile
-@@ -837,11 +837,43 @@ dtb-$(CONFIG_ARCH_QCOM) += \
+@@ -837,11 +837,44 @@ dtb-$(CONFIG_ARCH_QCOM) += \
  	qcom-apq8074-dragonboard.dtb \
  	qcom-apq8084-ifc6540.dtb \
  	qcom-apq8084-mtp.dtb \
@@ -44,6 +44,7 @@ Signed-off-by: John Crispin <john@phrozen.org>
 +	qcom-ipq4019-map-ac2200.dtb \
 +	qcom-ipq4019-e2600ac-c1.dtb \
 +	qcom-ipq4019-e2600ac-c2.dtb \
++	qcom-ipq4019-habanero-dvk.dtb \
 +	qcom-ipq4019-u4019-32m.dtb \
 +	qcom-ipq4019-wpj419.dtb \
 +	qcom-ipq4028-wpj428.dtb \