aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux
diff options
context:
space:
mode:
authorThibaut VARÈNE <hacks@slashdirt.org>2022-04-15 13:17:49 +0200
committerPetr Štetiar <ynezz@true.cz>2022-04-16 14:48:29 +0200
commit06874171d125f0a69d6fb8cfd12213b7913d317e (patch)
tree3d1082fb04eb2ec83c2f8a32a6b8483a92347306 /target/linux
parentc5ef62a218455f5d60b8f76307784a90a77dda43 (diff)
downloadupstream-06874171d125f0a69d6fb8cfd12213b7913d317e.tar.gz
upstream-06874171d125f0a69d6fb8cfd12213b7913d317e.tar.bz2
upstream-06874171d125f0a69d6fb8cfd12213b7913d317e.zip
ath79: add support for Yuncore XD3200
Specification: - QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR - 2T2R 802.11b/g/n 2.4GHz - 2T2R 802.11n/ac 5GHz - 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port) LED for 5 GHz WLAN is currently not supported as it is connected directly to the QCA9882 radio chip. Flash instructions: If your device comes with generic QSDK based firmware, you can login over telnet (login: root, empty password, default IP: 192.168.188.253), issue first (important!) 'fw_setenv' command and then perform regular upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download image to the device, SSH server is not available): fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000" sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin In case your device runs firmware with YunCore custom GUI, you can use U-Boot recovery mode: 1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with 'tftp' image renamed to 'upgrade.bin' 2. Power the device with reset button pressed and release it after 5-7 seconds, recovery mode should start downloading image from server (unfortunately, there is no visible indication that recovery got enabled - in case of problems check TFTP server logs) Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org> (cherry-picked from commit c91df224f54fdd44c9c0487a8c91876f5d273164)
Diffstat (limited to 'target/linux')
-rw-r--r--target/linux/ath79/dts/qca9563_yuncore_xd3200.dts32
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/01_leds3
-rwxr-xr-xtarget/linux/ath79/generic/base-files/etc/board.d/02_network1
-rw-r--r--target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata3
-rw-r--r--target/linux/ath79/image/generic.mk11
5 files changed, 48 insertions, 2 deletions
diff --git a/target/linux/ath79/dts/qca9563_yuncore_xd3200.dts b/target/linux/ath79/dts/qca9563_yuncore_xd3200.dts
new file mode 100644
index 0000000000..5c87752585
--- /dev/null
+++ b/target/linux/ath79/dts/qca9563_yuncore_xd3200.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "qca9563_yuncore_xd4200.dtsi"
+
+/ {
+ compatible = "yuncore,xd3200", "qca,qca9563";
+ model = "YunCore XD3200";
+
+ aliases {
+ label-mac-device = &eth0;
+ led-boot = &led_system;
+ led-failsafe = &led_system;
+ led-running = &led_system;
+ led-upgrade = &led_system;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led_system: system {
+ label = "green:system";
+ gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ };
+
+ wlan2g {
+ label = "blue:wlan2g";
+ gpios = <&gpio 19 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy1tpt";
+ };
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
index 3031b4703b..b6c68db813 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
@@ -220,7 +220,8 @@ glinet,gl-x750)
hak5,lan-turtle)
ucidef_set_led_netdev "wan" "WAN" "orange:system" "eth1"
;;
-joyit,jt-or750i)
+joyit,jt-or750i|\
+yuncore,xd3200)
ucidef_set_led_default "ath10k" "ath10k-disable" "ath10k-phy0" "0"
;;
meraki,mr12|\
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index d4f53e7dae..5bf78117e1 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -306,6 +306,7 @@ ath79_setup_interfaces()
ubnt,nanobeam-ac-gen2|\
ubnt,nanostation-ac|\
yuncore,a782|\
+ yuncore,xd3200|\
yuncore,xd4200)
ucidef_add_switch "switch0" \
"0@eth0" "2:lan" "3:wan"
diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 69735f3360..c562fa7c74 100644
--- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -44,7 +44,8 @@ case "$FIRMWARE" in
ubnt,powerbeam-5ac-500|\
ubnt,powerbeam-5ac-gen2|\
ubnt,unifiac-pro|\
- yuncore,a770)
+ yuncore,a770|\
+ yuncore,xd3200)
caldata_extract "art" 0x5000 0x844
;;
devolo,dvl1200e|\
diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk
index 304e589800..cac5dea3d2 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -2242,6 +2242,17 @@ define Device/yuncore_a782
endef
TARGET_DEVICES += yuncore_a782
+define Device/yuncore_xd3200
+ SOC := qca9563
+ DEVICE_VENDOR := YunCore
+ DEVICE_MODEL := XD3200
+ DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct
+ IMAGE_SIZE := 16000k
+ IMAGES += tftp.bin
+ IMAGE/tftp.bin := $$(IMAGE/sysupgrade.bin) | yuncore-tftp-header-16m
+endef
+TARGET_DEVICES += yuncore_xd3200
+
define Device/yuncore_xd4200
SOC := qca9563
DEVICE_VENDOR := YunCore