ath79: add tl-wr2543-v1 support

to switch between wlan leds we need a userspace implementation

Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>

5 files changed, 205 insertions, 0 deletions

diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network
index 743b877aba..d978c3441e 100755
--- a/target/linux/ath79/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/base-files/etc/board.d/02_network
@@ -70,6 +70,10 @@ ath79_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"0@eth1" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" "6@eth0"
 		;;
+	"tplink,tl-wr2543-v1")
+		ucidef_add_switch "switch0" \
+			"1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "9@eth0"
+		;;
 	"netgear,wndr3800")
 		ucidef_set_interfaces_lan_wan "eth0" "eth1"
 		ucidef_add_switch "switch0" \
diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
index 5b22b1544f..7023fa5e58 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom
@@ -57,6 +57,7 @@ case "$FIRMWARE" in
 	"netgear,wnr612-v2"|\
 	"on,n150r"|\
 	"tplink,tl-wr740n-v2"|\
+	"tplink,tl-wr2543-v1"|\
 	"ubnt,unifi")
 		ath9k_eeprom_extract "art" 4096 2048
 		;;
diff --git a/target/linux/ath79/config-4.14 b/target/linux/ath79/config-4.14
index 0e24582cc7..01d259572a 100644
--- a/target/linux/ath79/config-4.14
+++ b/target/linux/ath79/config-4.14
@@ -205,6 +205,7 @@ CONFIG_RESET_CONTROLLER=y
 CONFIG_RTL8366RB_PHY=y
 CONFIG_RTL8366S_PHY=y
 CONFIG_RTL8366_SMI=y
+CONFIG_RTL8367_PHY=y
 # CONFIG_SCHED_INFO is not set
 # CONFIG_SCSI_DMA is not set
 # CONFIG_SERIAL_8250_FSL is not set
diff --git a/target/linux/ath79/dts/ar7242_tl-wr2543-v1.dts b/target/linux/ath79/dts/ar7242_tl-wr2543-v1.dts
new file mode 100644
index 0000000000..0934fe0089
--- /dev/null
+++ b/target/linux/ath79/dts/ar7242_tl-wr2543-v1.dts
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar7242.dtsi"
+
+/ {
+	compatible = "tplink,tl-wr2543-v1", "qca,ar7242";
+	model = "TP-LINK TL-WR2543N/ND";
+
+	aliases {
+		led-status = &system;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x4000000>;
+	};
+
+	extosc: ref {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <40000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys-polled";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		poll-interval = <20>;
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+
+		wps {
+			label = "wps";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		system: wps {
+			label = "tplink:green:wps";
+			gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		usb {
+			label = "tplink:green:usb";
+			gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			trigger-sources = <&hub_port>;
+			linux,default-trigger = "usbport";
+		};
+	};
+
+	ath9k-leds {
+		compatible = "gpio-leds";
+
+		wlan2g {
+			label = "tplink:green:wlan2g";
+			gpios = <&ath9k 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "phy0tpt";
+		};
+
+		wlan5g {
+			label = "tplink:green:wlan5g";
+			gpios = <&ath9k 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "phy0tpt";
+		};
+
+	};
+
+	rtl8367 {
+		compatible = "realtek,rtl8367";
+		gpio-sda = <&gpio 1 GPIO_ACTIVE_HIGH>;
+		gpio-sck = <&gpio 6 GPIO_ACTIVE_HIGH>;
+		realtek,extif0 = <1 0 1 1 1 1 1 1 2>;
+
+		mdio-bus {
+			status = "okay";
+
+			phy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+		};
+	};
+};
+
+&pll {
+	clocks = <&extosc>;
+};
+
+&spi {
+	status = "okay";
+	num-cs = <1>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			uboot:	partition@0 {
+				label = "u-boot";
+				reg = <0x000000 0x020000>;
+				read-only;
+			};
+
+			partition@20000 {
+				label = "firmware";
+				reg = <0x020000 0x7d0000>;
+			};
+
+			partition@7f0000 {
+				label = "art";
+				reg = <0x7f0000 0x010000>;
+				read-only;
+			};
+		};
+	};
+};
+
+&uart {
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+
+	hub_port: port@1 {
+		reg = <1>;
+		#trigger-source-cells = <0>;
+	};
+};
+
+&usb_phy {
+	status = "okay";
+};
+
+&pcie {
+	status = "okay";
+
+	ath9k: wifi@0 {
+		reg = <0x0000 0 0 0 0>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		qca,no-eeprom;
+		mtd-mac-address = <&uboot 0x1fc00>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	mtd-mac-address = <&uboot 0x1fc00>;
+
+	phy-handle = <&phy0>;
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk
index 467e2c4c42..accaf3b68f 100644
--- a/target/linux/ath79/image/generic-tp-link.mk
+++ b/target/linux/ath79/image/generic-tp-link.mk
@@ -62,3 +62,16 @@ define Device/tl-wr1043nd-v4
   SUPPORTED_DEVICES := tplink,tl-wr1043nd-v4 tl-wr1043nd-v4
 endef
 TARGET_DEVICES += tl-wr1043nd-v4
+
+define Device/tl-wr2543-v1
+  $(Device/tplink-8mlzma)
+  ATH_SOC := ar7242
+  DEVICE_TITLE := TP-LINK TL-WR2543N/ND v1
+  DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport
+  TPLINK_HWID := 0x25430001
+  IMAGE/sysupgrade.bin := append-rootfs | mktplinkfw sysupgrade -v 3.13.99 | \
+    append-metadata | check-size $$$$(IMAGE_SIZE)
+  IMAGE/factory.bin := append-rootfs | mktplinkfw factory -v 3.13.99
+  SUPPORTED_DEVICES := tplink,tl-wr2543-v1 tl-wr2543-v1
+endef
+TARGET_DEVICES += tl-wr2543-v1