diff options
| author | Giuseppe Lippolis <giu.lippolis@gmail.com> | 2018-03-10 10:34:38 +0100 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2018-04-04 08:42:35 +0200 |
| commit | 6525bffc0a7ee6fabfe331a4d9e3eeabdd3516ae (patch) | |
| tree | 4d91984eefef92212b58ba195df91970e24f86bc /target/linux/ramips/base-files/etc | |
| parent | e9d5f8ebb25721c28a37390081fd4a08c3d0f8d4 (diff) | |
| download | upstream-6525bffc0a7ee6fabfe331a4d9e3eeabdd3516ae.tar.gz upstream-6525bffc0a7ee6fabfe331a4d9e3eeabdd3516ae.tar.bz2 upstream-6525bffc0a7ee6fabfe331a4d9e3eeabdd3516ae.zip | |
ramips: add support for DLINK DWR-921-C1
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.bin http://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Diffstat (limited to 'target/linux/ramips/base-files/etc')
4 files changed, 13 insertions, 2 deletions
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 4b8242cb9f..a34abbb69f 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -162,6 +162,11 @@ dlink,dwr-116-a1|\ mzk-ex300np) set_wifi_led "$boardname:green:wifi" ;; +dlink,dwr-921-c1) + set_wifi_led "$boardname:green:wifi" + ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0f" + ucidef_set_led_default "sigstrength" "Signal Strength" "$boardname:green:sigstrength" "0" + ;; dir-810l|\ mzk-750dhp|\ mzk-dp150n|\ diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 4441b2293e..8f3a95d3e3 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -81,6 +81,7 @@ ramips_setup_interfaces() dir-610-a1|\ dir-615-h1|\ dlink,dwr-116-a1|\ + dlink,dwr-921-c1|\ ew1200|\ firewrt|\ hc5661a|\ @@ -434,7 +435,8 @@ ramips_setup_macs() lan_mac=$(mtd_get_mac_ascii factory lanmac) wan_mac=$(mtd_get_mac_ascii factory wanmac) ;; - dlink,dwr-116-a1) + dlink,dwr-116-a1|\ + dlink,dwr-921-c1) wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000) lan_mac=$(macaddr_add "$wan_mac" 1) ;; diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index d9f131b2a8..7b90f6ba12 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -108,6 +108,9 @@ get_status_led() { zbt-wg2626) status_led="$boardname:green:status" ;; + dlink,dwr-921-c1) + status_led="$boardname:green:sigstrength" + ;; asl26555-8M|\ asl26555-16M) status_led="asl26555:green:power" diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom index 67c05c9a46..c0c6a3ecad 100644 --- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom +++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom @@ -54,7 +54,8 @@ board=$(board_name) case "$FIRMWARE" in "soc_wmac.eeprom") case $board in - dlink,dwr-116-a1) + dlink,dwr-116-a1|\ + dlink,dwr-921-c1) wan_mac=$(jboot_config_read -m -i $(find_mtd_part "config") -o 0xE000) wifi_mac=$(macaddr_add "$wan_mac" 1) jboot_eeprom_extract "config" 0xE000 |