diff options
| author | Chukun Pan <amadeus@jmu.edu.cn> | 2022-09-18 23:16:18 +0800 |
|---|---|---|
| committer | Daniel Golle <daniel@makrotopia.org> | 2022-10-30 14:30:22 +0000 |
| commit | 641e4f2f0479997c71ff6c1f1b63fb9b5c67e687 (patch) | |
| tree | a855d53853524d3069111f04b68b6e6686451b40 /target/linux/mediatek/filogic/base-files | |
| parent | 9d1e687da3e11785e633c37b30ddcfabb885c657 (diff) | |
| download | upstream-641e4f2f0479997c71ff6c1f1b63fb9b5c67e687.tar.gz upstream-641e4f2f0479997c71ff6c1f1b63fb9b5c67e687.tar.bz2 upstream-641e4f2f0479997c71ff6c1f1b63fb9b5c67e687.zip | |
mediatek: add Xiaomi Redmi Router AX6000 support
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128 MB
RAM: K4A4G165WF-BCWE 512 MB
Ethernet: 4x 10/100/1000 Mbps
WiFi1: MT7976GN 2.4GHz ax 4x4
WiFi2: MT7976AN 5GHz ax 4x4
Button: Mesh, Reset
Flash instructions:
1. Gain ssh and serial port access, see the link below:
https://openwrt.org/toh/xiaomi/redmi_ax6000#installation
2. Use ssh or serial port to log in to the router, and
execute the following command:
nvram set boot_wait=on
nvram set flag_boot_rootfs=0
nvram set flag_boot_success=1
nvram set flag_last_success=1
nvram set flag_try_sys1_failed=8
nvram set flag_try_sys2_failed=8
nvram commit
3. Set a static ip on the ethernet interface of your computer
(e.g. default: ip 192.168.31.100, gateway 192.168.31.1)
4. Download the initramfs image, rename it to initramfs.bin,
and host it with the tftp server.
5. Interrupt U-Boot and run these commands:
setenv mtdparts nmbm0:1024k(bl2),256k(Nvram),256k(Bdata),2048k(factory),2048k(fip),256k(crash),256k(crash_log),112640k(ubi)
saveenv
tftpboot initramfs.bin
bootm
6. After openwrt boots up, use scp or luci web
to upload sysupgrade.bin to upgrade.
Revert to stock firmware:
Restore mtdparts back to default, then use the
vendor's recovery tool (Windows only).
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Diffstat (limited to 'target/linux/mediatek/filogic/base-files')
| -rw-r--r-- | target/linux/mediatek/filogic/base-files/etc/board.d/02_network | 23 |
1 files changed, 23 insertions, 0 deletions
diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index f7dc7a01e0..0f0a0fc86b 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -16,15 +16,38 @@ mediatek_setup_interfaces() ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 sfp2" "eth1 wan" ucidef_set_interface_macaddr "wan" "$(macaddr_add $(cat /sys/class/net/eth0/address) 1)" ;; + xiaomi,redmi-router-ax6000) + ucidef_set_interfaces_lan_wan "lan2 lan3 lan4" wan + ;; *) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan ;; esac } +mediatek_setup_macs() +{ + local board="$1" + local lan_mac="" + local wan_mac="" + local label_mac="" + + case $board in + xiaomi,redmi-router-ax6000) + wan_mac=$(mtd_get_mac_ascii Bdata ethaddr_wan) + label_mac=$wan_mac + ;; + esac + + [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac + [ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac + [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac +} + board_config_update board=$(board_name) mediatek_setup_interfaces $board +mediatek_setup_macs $board board_config_flush exit 0 |