diff options
| author | Dongming Han <handongming@gl-inet.com> | 2020-04-08 16:43:51 +0800 |
|---|---|---|
| committer | Petr Štetiar <ynezz@true.cz> | 2020-07-08 16:07:05 +0200 |
| commit | f103321349182d5fef5a1b846f017db32005da87 (patch) | |
| tree | 676da18dceaf83d292a8d7814059277ae93b5e39 /target/linux/ipq40xx/base-files | |
| parent | b88f8202c4ced971de26268597d2e798ecdc0ba2 (diff) | |
| download | upstream-f103321349182d5fef5a1b846f017db32005da87.tar.gz upstream-f103321349182d5fef5a1b846f017db32005da87.tar.bz2 upstream-f103321349182d5fef5a1b846f017db32005da87.zip | |
ipq40xx: add support for GL.iNet GL-S1300
Specifications:
SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM: 512 MiB
FLASH1: 16 MiB NOR - SPI0
FLASH2: 8 GiB eMMC
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT: Reset, WPS
LED: Power, Mesh, WLAN
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2: On board with BLE module
SPI1: On board socket for Zigbee module
Install via tftp
- NB: need to flash transition image firstly
Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf
Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
Diffstat (limited to 'target/linux/ipq40xx/base-files')
| -rwxr-xr-x | target/linux/ipq40xx/base-files/etc/board.d/02_network | 3 | ||||
| -rw-r--r-- | target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata | 2 |
2 files changed, 4 insertions, 1 deletions
diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 77a2241283..cd336a9e6a 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -75,7 +75,8 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "2:lan:3" "3:lan:2" "4:lan:1" "0u@eth1" "5:wan" ;; - glinet,gl-b1300) + glinet,gl-b1300 |\ + glinet,gl-s1300) ucidef_set_interfaces_lan_wan "eth0" "eth1" ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index e41baecf69..b95bab7cae 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -50,6 +50,7 @@ case "$FIRMWARE" in cilab,meshpoint-one |\ ezviz,cs-w3-wd1200g-eup |\ glinet,gl-b1300 |\ + glinet,gl-s1300 |\ linksys,ea6350v3 |\ mobipromo,cm520-79f |\ qcom,ap-dk01.1-c1) @@ -138,6 +139,7 @@ case "$FIRMWARE" in cilab,meshpoint-one |\ ezviz,cs-w3-wd1200g-eup |\ glinet,gl-b1300 |\ + glinet,gl-s1300 |\ linksys,ea6350v3 |\ mobipromo,cm520-79f |\ qcom,ap-dk01.1-c1) |