kernel: backport Broadcom thermal drivers

This includes driver for Northstar and for Raspberry Pi.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>

1 files changed, 365 insertions, 0 deletions

diff --git a/target/linux/generic/patches-4.4/086-0003-thermal-bcm2835-add-thermal-driver-for-bcm2835-SoC.patch b/target/linux/generic/patches-4.4/086-0003-thermal-bcm2835-add-thermal-driver-for-bcm2835-SoC.patch
new file mode 100644
index 0000000000..d606804de6
--- /dev/null
+++ b/target/linux/generic/patches-4.4/086-0003-thermal-bcm2835-add-thermal-driver-for-bcm2835-SoC.patch
@@ -0,0 +1,365 @@
+From bcb7dd9ef206f7d646ed8dac6fe7772083714253 Mon Sep 17 00:00:00 2001
+From: Stefan Wahren <stefan.wahren@i2se.com>
+Date: Fri, 31 Mar 2017 20:03:06 +0000
+Subject: [PATCH] thermal: bcm2835: add thermal driver for bcm2835 SoC
+MIME-Version: 1.0
+Content-Type: text/plain; charset=UTF-8
+Content-Transfer-Encoding: 8bit
+
+Add basic thermal driver for bcm2835 SoC.
+
+This driver currently make sure that tsense HW block is set up
+correctly.
+
+Tested-by: Rafał Miłecki <rafal@milecki.pl>
+Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
+Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
+Acked-by: Eric Anholt <eric@anholt.net>
+Acked-by: Eduardo Valentin <edubezval@gmail.com>
+Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
+---
+ drivers/thermal/Kconfig           |   8 +
+ drivers/thermal/Makefile          |   1 +
+ drivers/thermal/bcm2835_thermal.c | 314 ++++++++++++++++++++++++++++++++++++++
+ 3 files changed, 323 insertions(+)
+ create mode 100644 drivers/thermal/bcm2835_thermal.c
+
+--- a/drivers/thermal/Kconfig
++++ b/drivers/thermal/Kconfig
+@@ -391,4 +391,12 @@ config QCOM_SPMI_TEMP_ALARM
+ 	  real time die temperature if an ADC is present or an estimate of the
+ 	  temperature based upon the over temperature stage value.
+ 
++config BCM2835_THERMAL
++	tristate "Thermal sensors on bcm2835 SoC"
++	depends on ARCH_BCM2835 || COMPILE_TEST
++	depends on HAS_IOMEM
++	depends on THERMAL_OF
++	help
++	  Support for thermal sensors on Broadcom bcm2835 SoCs.
++
+ endif
+--- a/drivers/thermal/Makefile
++++ b/drivers/thermal/Makefile
+@@ -48,3 +48,4 @@ obj-$(CONFIG_INTEL_PCH_THERMAL)	+= intel
+ obj-$(CONFIG_ST_THERMAL)	+= st/
+ obj-$(CONFIG_TEGRA_SOCTHERM)	+= tegra_soctherm.o
+ obj-$(CONFIG_HISI_THERMAL)     += hisi_thermal.o
++obj-$(CONFIG_BCM2835_THERMAL) += bcm2835_thermal.o
+--- /dev/null
++++ b/drivers/thermal/bcm2835_thermal.c
+@@ -0,0 +1,314 @@
++/*
++ * Driver for Broadcom BCM2835 SoC temperature sensor
++ *
++ * Copyright (C) 2016 Martin Sperl
++ *
++ * This program is free software; you can redistribute it and/or modify
++ * it under the terms of the GNU General Public License as published by
++ * the Free Software Foundation; either version 2 of the License, or
++ * (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
++ * GNU General Public License for more details.
++ */
++
++#include <linux/clk.h>
++#include <linux/debugfs.h>
++#include <linux/device.h>
++#include <linux/err.h>
++#include <linux/io.h>
++#include <linux/kernel.h>
++#include <linux/module.h>
++#include <linux/of.h>
++#include <linux/of_address.h>
++#include <linux/of_device.h>
++#include <linux/platform_device.h>
++#include <linux/thermal.h>
++
++#define BCM2835_TS_TSENSCTL			0x00
++#define BCM2835_TS_TSENSSTAT			0x04
++
++#define BCM2835_TS_TSENSCTL_PRWDW		BIT(0)
++#define BCM2835_TS_TSENSCTL_RSTB		BIT(1)
++
++/*
++ * bandgap reference voltage in 6 mV increments
++ * 000b = 1178 mV, 001b = 1184 mV, ... 111b = 1220 mV
++ */
++#define BCM2835_TS_TSENSCTL_CTRL_BITS		3
++#define BCM2835_TS_TSENSCTL_CTRL_SHIFT		2
++#define BCM2835_TS_TSENSCTL_CTRL_MASK		    \
++	GENMASK(BCM2835_TS_TSENSCTL_CTRL_BITS +     \
++		BCM2835_TS_TSENSCTL_CTRL_SHIFT - 1, \
++		BCM2835_TS_TSENSCTL_CTRL_SHIFT)
++#define BCM2835_TS_TSENSCTL_CTRL_DEFAULT	1
++#define BCM2835_TS_TSENSCTL_EN_INT		BIT(5)
++#define BCM2835_TS_TSENSCTL_DIRECT		BIT(6)
++#define BCM2835_TS_TSENSCTL_CLR_INT		BIT(7)
++#define BCM2835_TS_TSENSCTL_THOLD_SHIFT		8
++#define BCM2835_TS_TSENSCTL_THOLD_BITS		10
++#define BCM2835_TS_TSENSCTL_THOLD_MASK		     \
++	GENMASK(BCM2835_TS_TSENSCTL_THOLD_BITS +     \
++		BCM2835_TS_TSENSCTL_THOLD_SHIFT - 1, \
++		BCM2835_TS_TSENSCTL_THOLD_SHIFT)
++/*
++ * time how long the block to be asserted in reset
++ * which based on a clock counter (TSENS clock assumed)
++ */
++#define BCM2835_TS_TSENSCTL_RSTDELAY_SHIFT	18
++#define BCM2835_TS_TSENSCTL_RSTDELAY_BITS	8
++#define BCM2835_TS_TSENSCTL_REGULEN		BIT(26)
++
++#define BCM2835_TS_TSENSSTAT_DATA_BITS		10
++#define BCM2835_TS_TSENSSTAT_DATA_SHIFT		0
++#define BCM2835_TS_TSENSSTAT_DATA_MASK		     \
++	GENMASK(BCM2835_TS_TSENSSTAT_DATA_BITS +     \
++		BCM2835_TS_TSENSSTAT_DATA_SHIFT - 1, \
++		BCM2835_TS_TSENSSTAT_DATA_SHIFT)
++#define BCM2835_TS_TSENSSTAT_VALID		BIT(10)
++#define BCM2835_TS_TSENSSTAT_INTERRUPT		BIT(11)
++
++struct bcm2835_thermal_data {
++	struct thermal_zone_device *tz;
++	void __iomem *regs;
++	struct clk *clk;
++	struct dentry *debugfsdir;
++};
++
++static int bcm2835_thermal_adc2temp(u32 adc, int offset, int slope)
++{
++	return offset + slope * adc;
++}
++
++static int bcm2835_thermal_temp2adc(int temp, int offset, int slope)
++{
++	temp -= offset;
++	temp /= slope;
++
++	if (temp < 0)
++		temp = 0;
++	if (temp >= BIT(BCM2835_TS_TSENSSTAT_DATA_BITS))
++		temp = BIT(BCM2835_TS_TSENSSTAT_DATA_BITS) - 1;
++
++	return temp;
++}
++
++static int bcm2835_thermal_get_temp(void *d, int *temp)
++{
++	struct bcm2835_thermal_data *data = d;
++	u32 val = readl(data->regs + BCM2835_TS_TSENSSTAT);
++
++	if (!(val & BCM2835_TS_TSENSSTAT_VALID))
++		return -EIO;
++
++	val &= BCM2835_TS_TSENSSTAT_DATA_MASK;
++
++	*temp = bcm2835_thermal_adc2temp(
++		val,
++		thermal_zone_get_offset(data->tz),
++		thermal_zone_get_slope(data->tz));
++
++	return 0;
++}
++
++static const struct debugfs_reg32 bcm2835_thermal_regs[] = {
++	{
++		.name = "ctl",
++		.offset = 0
++	},
++	{
++		.name = "stat",
++		.offset = 4
++	}
++};
++
++static void bcm2835_thermal_debugfs(struct platform_device *pdev)
++{
++	struct thermal_zone_device *tz = platform_get_drvdata(pdev);
++	struct bcm2835_thermal_data *data = tz->devdata;
++	struct debugfs_regset32 *regset;
++
++	data->debugfsdir = debugfs_create_dir("bcm2835_thermal", NULL);
++	if (!data->debugfsdir)
++		return;
++
++	regset = devm_kzalloc(&pdev->dev, sizeof(*regset), GFP_KERNEL);
++	if (!regset)
++		return;
++
++	regset->regs = bcm2835_thermal_regs;
++	regset->nregs = ARRAY_SIZE(bcm2835_thermal_regs);
++	regset->base = data->regs;
++
++	debugfs_create_regset32("regset", 0444, data->debugfsdir, regset);
++}
++
++static struct thermal_zone_of_device_ops bcm2835_thermal_ops = {
++	.get_temp = bcm2835_thermal_get_temp,
++};
++
++/*
++ * Note: as per Raspberry Foundation FAQ
++ * (https://www.raspberrypi.org/help/faqs/#performanceOperatingTemperature)
++ * the recommended temperature range for the SoC -40C to +85C
++ * so the trip limit is set to 80C.
++ * this applies to all the BCM283X SoC
++ */
++
++static const struct of_device_id bcm2835_thermal_of_match_table[] = {
++	{
++		.compatible = "brcm,bcm2835-thermal",
++	},
++	{
++		.compatible = "brcm,bcm2836-thermal",
++	},
++	{
++		.compatible = "brcm,bcm2837-thermal",
++	},
++	{},
++};
++MODULE_DEVICE_TABLE(of, bcm2835_thermal_of_match_table);
++
++static int bcm2835_thermal_probe(struct platform_device *pdev)
++{
++	const struct of_device_id *match;
++	struct thermal_zone_device *tz;
++	struct bcm2835_thermal_data *data;
++	struct resource *res;
++	int err = 0;
++	u32 val;
++	unsigned long rate;
++
++	data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
++	if (!data)
++		return -ENOMEM;
++
++	match = of_match_device(bcm2835_thermal_of_match_table,
++				&pdev->dev);
++	if (!match)
++		return -EINVAL;
++
++	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
++	data->regs = devm_ioremap_resource(&pdev->dev, res);
++	if (IS_ERR(data->regs)) {
++		err = PTR_ERR(data->regs);
++		dev_err(&pdev->dev, "Could not get registers: %d\n", err);
++		return err;
++	}
++
++	data->clk = devm_clk_get(&pdev->dev, NULL);
++	if (IS_ERR(data->clk)) {
++		err = PTR_ERR(data->clk);
++		if (err != -EPROBE_DEFER)
++			dev_err(&pdev->dev, "Could not get clk: %d\n", err);
++		return err;
++	}
++
++	err = clk_prepare_enable(data->clk);
++	if (err)
++		return err;
++
++	rate = clk_get_rate(data->clk);
++	if ((rate < 1920000) || (rate > 5000000))
++		dev_warn(&pdev->dev,
++			 "Clock %pCn running at %pCr Hz is outside of the recommended range: 1.92 to 5MHz\n",
++			 data->clk, data->clk);
++
++	/* register of thermal sensor and get info from DT */
++	tz = thermal_zone_of_sensor_register(&pdev->dev, 0, data,
++					     &bcm2835_thermal_ops);
++	if (IS_ERR(tz)) {
++		err = PTR_ERR(tz);
++		dev_err(&pdev->dev,
++			"Failed to register the thermal device: %d\n",
++			err);
++		goto err_clk;
++	}
++
++	/*
++	 * right now the FW does set up the HW-block, so we are not
++	 * touching the configuration registers.
++	 * But if the HW is not enabled, then set it up
++	 * using "sane" values used by the firmware right now.
++	 */
++	val = readl(data->regs + BCM2835_TS_TSENSCTL);
++	if (!(val & BCM2835_TS_TSENSCTL_RSTB)) {
++		int trip_temp, offset, slope;
++
++		slope = thermal_zone_get_slope(tz);
++		offset = thermal_zone_get_offset(tz);
++		/*
++		 * For now we deal only with critical, otherwise
++		 * would need to iterate
++		 */
++		err = tz->ops->get_trip_temp(tz, 0, &trip_temp);
++		if (err < 0) {
++			err = PTR_ERR(tz);
++			dev_err(&pdev->dev,
++				"Not able to read trip_temp: %d\n",
++				err);
++			goto err_tz;
++		}
++
++		/* set bandgap reference voltage and enable voltage regulator */
++		val = (BCM2835_TS_TSENSCTL_CTRL_DEFAULT <<
++		       BCM2835_TS_TSENSCTL_CTRL_SHIFT) |
++		      BCM2835_TS_TSENSCTL_REGULEN;
++
++		/* use the recommended reset duration */
++		val |= (0xFE << BCM2835_TS_TSENSCTL_RSTDELAY_SHIFT);
++
++		/*  trip_adc value from info */
++		val |= bcm2835_thermal_temp2adc(trip_temp,
++						offset,
++						slope)
++			<< BCM2835_TS_TSENSCTL_THOLD_SHIFT;
++
++		/* write the value back to the register as 2 steps */
++		writel(val, data->regs + BCM2835_TS_TSENSCTL);
++		val |= BCM2835_TS_TSENSCTL_RSTB;
++		writel(val, data->regs + BCM2835_TS_TSENSCTL);
++	}
++
++	data->tz = tz;
++
++	platform_set_drvdata(pdev, tz);
++
++	bcm2835_thermal_debugfs(pdev);
++
++	return 0;
++err_tz:
++	thermal_zone_of_sensor_unregister(&pdev->dev, tz);
++err_clk:
++	clk_disable_unprepare(data->clk);
++
++	return err;
++}
++
++static int bcm2835_thermal_remove(struct platform_device *pdev)
++{
++	struct thermal_zone_device *tz = platform_get_drvdata(pdev);
++	struct bcm2835_thermal_data *data = tz->devdata;
++
++	debugfs_remove_recursive(data->debugfsdir);
++	thermal_zone_of_sensor_unregister(&pdev->dev, tz);
++	clk_disable_unprepare(data->clk);
++
++	return 0;
++}
++
++static struct platform_driver bcm2835_thermal_driver = {
++	.probe = bcm2835_thermal_probe,
++	.remove = bcm2835_thermal_remove,
++	.driver = {
++		.name = "bcm2835_thermal",
++		.of_match_table = bcm2835_thermal_of_match_table,
++	},
++};
++module_platform_driver(bcm2835_thermal_driver);
++
++MODULE_AUTHOR("Martin Sperl");
++MODULE_DESCRIPTION("Thermal driver for bcm2835 chip");
++MODULE_LICENSE("GPL");