brcm2708: rename all patches from raspberrypi git tree to use 950 prefix

Right now all brcm2708 patches are extracted from the non-mainline
raspberrypi/linux git tree. Many of them are hacks and/or are unneeded
in LEDE. Raspberry Pi is getting better and better mainline support so
it would be nice to finally start maintaining patches in a cleaner way:
1) Backport patches accepted in upstream tree
2) Start using upstream drivers
3) Pick only these patches that are needed for more complete support

Handling above tasks requires grouping patches - ideally using the same
prefixes as generic ones. It means we should rename existing patches to
use some high prefix. This will allow e.g. use 0xx for backported code.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>

1 files changed, 262 insertions, 0 deletions

diff --git a/target/linux/brcm2708/patches-4.9/950-0046-Add-cpufreq-driver.patch b/target/linux/brcm2708/patches-4.9/950-0046-Add-cpufreq-driver.patch
new file mode 100644
index 0000000000..7c5691c120
--- /dev/null
+++ b/target/linux/brcm2708/patches-4.9/950-0046-Add-cpufreq-driver.patch
@@ -0,0 +1,262 @@
+From 7d4719c360b755637c2e68f9855be282cd0065b6 Mon Sep 17 00:00:00 2001
+From: popcornmix <popcornmix@gmail.com>
+Date: Wed, 3 Jul 2013 00:49:20 +0100
+Subject: [PATCH] Add cpufreq driver
+
+Signed-off-by: popcornmix <popcornmix@gmail.com>
+---
+ drivers/cpufreq/Kconfig.arm       |   9 ++
+ drivers/cpufreq/Makefile          |   1 +
+ drivers/cpufreq/bcm2835-cpufreq.c | 218 ++++++++++++++++++++++++++++++++++++++
+ 3 files changed, 228 insertions(+)
+ create mode 100644 drivers/cpufreq/bcm2835-cpufreq.c
+
+--- a/drivers/cpufreq/Kconfig.arm
++++ b/drivers/cpufreq/Kconfig.arm
+@@ -220,6 +220,15 @@ config ARM_STI_CPUFREQ
+ 	  this config option if you wish to add CPUFreq support for STi based
+ 	  SoCs.
+ 
++config ARM_BCM2835_CPUFREQ
++	depends on RASPBERRYPI_FIRMWARE
++	bool "BCM2835 Driver"
++	default y
++	help
++	  This adds the CPUFreq driver for BCM2835
++
++	  If in doubt, say N.
++
+ config ARM_TEGRA20_CPUFREQ
+ 	bool "Tegra20 CPUFreq support"
+ 	depends on ARCH_TEGRA
+--- a/drivers/cpufreq/Makefile
++++ b/drivers/cpufreq/Makefile
+@@ -75,6 +75,7 @@ obj-$(CONFIG_ARM_SA1110_CPUFREQ)	+= sa11
+ obj-$(CONFIG_ARM_SCPI_CPUFREQ)		+= scpi-cpufreq.o
+ obj-$(CONFIG_ARM_SPEAR_CPUFREQ)		+= spear-cpufreq.o
+ obj-$(CONFIG_ARM_STI_CPUFREQ)		+= sti-cpufreq.o
++obj-$(CONFIG_ARM_BCM2835_CPUFREQ)	+= bcm2835-cpufreq.o
+ obj-$(CONFIG_ARM_TEGRA20_CPUFREQ)	+= tegra20-cpufreq.o
+ obj-$(CONFIG_ARM_TEGRA124_CPUFREQ)	+= tegra124-cpufreq.o
+ obj-$(CONFIG_ARM_VEXPRESS_SPC_CPUFREQ)	+= vexpress-spc-cpufreq.o
+--- /dev/null
++++ b/drivers/cpufreq/bcm2835-cpufreq.c
+@@ -0,0 +1,218 @@
++/*****************************************************************************
++* Copyright 2011 Broadcom Corporation.  All rights reserved.
++*
++* Unless you and Broadcom execute a separate written software license
++* agreement governing use of this software, this software is licensed to you
++* under the terms of the GNU General Public License version 2, available at
++* http://www.broadcom.com/licenses/GPLv2.php (the "GPL").
++*
++* Notwithstanding the above, under no circumstances may you combine this
++* software in any way with any other Broadcom software provided under a
++* license other than the GPL, without Broadcom's express prior written
++* consent.
++*****************************************************************************/
++
++/*****************************************************************************
++* FILENAME: bcm2835-cpufreq.h
++* DESCRIPTION: This driver dynamically manages the CPU Frequency of the ARM
++* processor. Messages are sent to Videocore either setting or requesting the
++* frequency of the ARM in order to match an appropiate frequency to the current
++* usage of the processor. The policy which selects the frequency to use is
++* defined in the kernel .config file, but can be changed during runtime.
++*****************************************************************************/
++
++/* ---------- INCLUDES ---------- */
++#include <linux/kernel.h>
++#include <linux/init.h>
++#include <linux/module.h>
++#include <linux/cpufreq.h>
++#include <soc/bcm2835/raspberrypi-firmware.h>
++
++/* ---------- DEFINES ---------- */
++/*#define CPUFREQ_DEBUG_ENABLE*/		/* enable debugging */
++#define MODULE_NAME "bcm2835-cpufreq"
++
++#define VCMSG_ID_ARM_CLOCK 0x000000003		/* Clock/Voltage ID's */
++
++/* debug printk macros */
++#ifdef CPUFREQ_DEBUG_ENABLE
++#define print_debug(fmt,...) pr_debug("%s:%s:%d: "fmt, MODULE_NAME, __func__, __LINE__, ##__VA_ARGS__)
++#else
++#define print_debug(fmt,...)
++#endif
++#define print_err(fmt,...) pr_err("%s:%s:%d: "fmt, MODULE_NAME, __func__,__LINE__, ##__VA_ARGS__)
++#define print_info(fmt,...) pr_info("%s: "fmt, MODULE_NAME, ##__VA_ARGS__)
++
++/* ---------- GLOBALS ---------- */
++static struct cpufreq_driver bcm2835_cpufreq_driver;	/* the cpufreq driver global */
++static unsigned int min_frequency, max_frequency;
++static struct cpufreq_frequency_table bcm2835_freq_table[3];
++
++/*
++ ===============================================
++  clk_rate either gets or sets the clock rates.
++ ===============================================
++*/
++
++static int bcm2835_cpufreq_clock_property(u32 tag, u32 id, u32 *val)
++{
++	struct rpi_firmware *fw = rpi_firmware_get(NULL);
++	struct {
++		u32 id;
++		u32 val;
++	} packet;
++	int ret;
++
++	packet.id = id;
++	packet.val = *val;
++	ret = rpi_firmware_property(fw, tag, &packet, sizeof(packet));
++	if (ret)
++		return ret;
++
++	*val = packet.val;
++
++	return 0;
++}
++
++static uint32_t bcm2835_cpufreq_set_clock(int cur_rate, int arm_rate)
++{
++	u32 rate = arm_rate * 1000;
++	int ret;
++
++	ret = bcm2835_cpufreq_clock_property(RPI_FIRMWARE_SET_CLOCK_RATE, VCMSG_ID_ARM_CLOCK, &rate);
++	if (ret) {
++		print_err("Failed to set clock: %d (%d)\n", arm_rate, ret);
++		return 0;
++	}
++
++	rate /= 1000;
++	print_debug("Setting new frequency = %d -> %d (actual %d)\n", cur_rate, arm_rate, rate);
++
++	return rate;
++}
++
++static uint32_t bcm2835_cpufreq_get_clock(int tag)
++{
++	u32 rate;
++	int ret;
++
++	ret = bcm2835_cpufreq_clock_property(tag, VCMSG_ID_ARM_CLOCK, &rate);
++	if (ret) {
++		print_err("Failed to get clock (%d)\n", ret);
++		return 0;
++	}
++
++	rate /= 1000;
++	print_debug("%s frequency = %u\n",
++		tag == RPI_FIRMWARE_GET_CLOCK_RATE ? "Current":
++		tag == RPI_FIRMWARE_GET_MIN_CLOCK_RATE ? "Min":
++		tag == RPI_FIRMWARE_GET_MAX_CLOCK_RATE ? "Max":
++		"Unexpected", rate);
++
++	return rate;
++}
++
++/*
++ ====================================================
++  Module Initialisation registers the cpufreq driver
++ ====================================================
++*/
++static int __init bcm2835_cpufreq_module_init(void)
++{
++	print_debug("IN\n");
++	return cpufreq_register_driver(&bcm2835_cpufreq_driver);
++}
++
++/*
++ =============
++  Module exit
++ =============
++*/
++static void __exit bcm2835_cpufreq_module_exit(void)
++{
++	print_debug("IN\n");
++	cpufreq_unregister_driver(&bcm2835_cpufreq_driver);
++	return;
++}
++
++/*
++ ==============================================================
++  Initialisation function sets up the CPU policy for first use
++ ==============================================================
++*/
++static int bcm2835_cpufreq_driver_init(struct cpufreq_policy *policy)
++{
++	/* measured value of how long it takes to change frequency */
++	const unsigned int transition_latency = 355000; /* ns */
++
++	if (!rpi_firmware_get(NULL)) {
++		print_err("Firmware is not available\n");
++		return -ENODEV;
++	}
++
++	/* now find out what the maximum and minimum frequencies are */
++	min_frequency = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_MIN_CLOCK_RATE);
++	max_frequency = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_MAX_CLOCK_RATE);
++
++	if (min_frequency == max_frequency) {
++		bcm2835_freq_table[0].frequency = min_frequency;
++		bcm2835_freq_table[1].frequency = CPUFREQ_TABLE_END;
++	} else {
++		bcm2835_freq_table[0].frequency = min_frequency;
++		bcm2835_freq_table[1].frequency = max_frequency;
++		bcm2835_freq_table[2].frequency = CPUFREQ_TABLE_END;
++	}
++
++	print_info("min=%d max=%d\n", min_frequency, max_frequency);
++	return cpufreq_generic_init(policy, bcm2835_freq_table, transition_latency);
++}
++
++/*
++ =====================================================================
++  Target index function chooses the requested frequency from the table
++ =====================================================================
++*/
++
++static int bcm2835_cpufreq_driver_target_index(struct cpufreq_policy *policy, unsigned int state)
++{
++	unsigned int target_freq = state == 0 ? min_frequency : max_frequency;
++	unsigned int cur = bcm2835_cpufreq_set_clock(policy->cur, target_freq);
++
++	if (!cur)
++	{
++		print_err("Error occurred setting a new frequency (%d)\n", target_freq);
++		return -EINVAL;
++	}
++	print_debug("%s: %i: freq %d->%d\n", policy->governor->name, state, policy->cur, cur);
++	return 0;
++}
++
++/*
++ ======================================================
++  Get function returns the current frequency from table
++ ======================================================
++*/
++
++static unsigned int bcm2835_cpufreq_driver_get(unsigned int cpu)
++{
++	unsigned int actual_rate = bcm2835_cpufreq_get_clock(RPI_FIRMWARE_GET_CLOCK_RATE);
++	print_debug("cpu%d: freq=%d\n", cpu, actual_rate);
++	return actual_rate <= min_frequency ? min_frequency : max_frequency;
++}
++
++/* the CPUFreq driver */
++static struct cpufreq_driver bcm2835_cpufreq_driver = {
++	.name         = "BCM2835 CPUFreq",
++	.init         = bcm2835_cpufreq_driver_init,
++	.verify       = cpufreq_generic_frequency_table_verify,
++	.target_index = bcm2835_cpufreq_driver_target_index,
++	.get          = bcm2835_cpufreq_driver_get,
++	.attr         = cpufreq_generic_attr,
++};
++
++MODULE_AUTHOR("Dorian Peake and Dom Cobley");
++MODULE_DESCRIPTION("CPU frequency driver for BCM2835 chip");
++MODULE_LICENSE("GPL");
++
++module_init(bcm2835_cpufreq_module_init);
++module_exit(bcm2835_cpufreq_module_exit);