adm5120: Remove unmaintained target

This target only supports kernel 3.18, which is not supported in OpenWrt
any more for multiple releases. It also looks like there is no active
maintainer for this target.
Remove the code and all the packages which are only used by this target.

To add this target to OpenWrt again port it to a recent and supported
kernel version.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>

14 files changed, 0 insertions, 2253 deletions

diff --git a/target/linux/adm5120/image/lzma-loader/Makefile b/target/linux/adm5120/image/lzma-loader/Makefile
deleted file mode 100644
index 36dfd09eae..0000000000
--- a/target/linux/adm5120/image/lzma-loader/Makefile
+++ /dev/null
@@ -1,62 +0,0 @@
-#
-# Copyright (C) 2006 OpenWrt.org
-#
-# This is free software, licensed under the GNU General Public License v2.
-# See /LICENSE for more information.
-#
-
-include $(TOPDIR)/rules.mk
-
-LOADER		:= loader.bin
-LOADER_NAME	:= $(basename $(notdir $(LOADER)))
-LOADER_DATA 	:=
-TARGET_DIR	:=
-
-ifeq ($(TARGET_DIR),)
-TARGET_DIR	:= $(KDIR)
-endif
-
-LOADER_BIN	:= $(TARGET_DIR)/$(LOADER_NAME).bin
-LOADER_GZ	:= $(TARGET_DIR)/$(LOADER_NAME).gz
-LOADER_ELF	:= $(TARGET_DIR)/$(LOADER_NAME).elf
-
-LZMA_STARTUP_ORG:= 0
-LZMA_TEXT_START	:= 0x80300000
-
-PKG_NAME := lzma-loader
-PKG_BUILD_DIR := $(KDIR)/$(PKG_NAME)
-
-.PHONY : loader-compile loader.bin loader.elf loader.gz
-
-$(PKG_BUILD_DIR)/.prepared:
-	mkdir $(PKG_BUILD_DIR)
-	$(CP) ./src/* $(PKG_BUILD_DIR)/
-	touch $@
-
-loader-compile: $(PKG_BUILD_DIR)/.prepared
-	$(MAKE) -C $(PKG_BUILD_DIR) CROSS_COMPILE="$(TARGET_CROSS)" \
-		LZMA_STARTUP_ORG=$(LZMA_STARTUP_ORG) \
-		LZMA_TEXT_START=$(LZMA_TEXT_START) \
-		LOADER_DATA=$(LOADER_DATA) \
-		CONFIG_BOARD=$(CONFIG_BOARD) \
-		CONFIG_PASS_KARGS=$(CONFIG_PASS_KARGS) \
-		clean all
-
-loader.gz: $(PKG_BUILD_DIR)/loader.bin
-	gzip -nc9 $< > $(LOADER_GZ)
-
-loader.elf: $(PKG_BUILD_DIR)/loader.elf
-	$(CP) $< $(LOADER_ELF)
-
-loader.bin: $(PKG_BUILD_DIR)/loader.bin
-	$(CP) $< $(LOADER_BIN)
-
-download:
-prepare: $(PKG_BUILD_DIR)/.prepared
-compile: loader-compile
-
-install:
-
-clean:
-	rm -rf $(PKG_BUILD_DIR)
-
diff --git a/target/linux/adm5120/image/lzma-loader/src/LzmaDecode.c b/target/linux/adm5120/image/lzma-loader/src/LzmaDecode.c
deleted file mode 100644
index cb8345377e..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/LzmaDecode.c
+++ /dev/null
@@ -1,584 +0,0 @@
-/*
-  LzmaDecode.c
-  LZMA Decoder (optimized for Speed version)
-  
-  LZMA SDK 4.40 Copyright (c) 1999-2006 Igor Pavlov (2006-05-01)
-  http://www.7-zip.org/
-
-  LZMA SDK is licensed under two licenses:
-  1) GNU Lesser General Public License (GNU LGPL)
-  2) Common Public License (CPL)
-  It means that you can select one of these two licenses and 
-  follow rules of that license.
-
-  SPECIAL EXCEPTION:
-  Igor Pavlov, as the author of this Code, expressly permits you to 
-  statically or dynamically link your Code (or bind by name) to the 
-  interfaces of this file without subjecting your linked Code to the 
-  terms of the CPL or GNU LGPL. Any modifications or additions 
-  to this file, however, are subject to the LGPL or CPL terms.
-*/
-
-#include "LzmaDecode.h"
-
-#define kNumTopBits 24
-#define kTopValue ((UInt32)1 << kNumTopBits)
-
-#define kNumBitModelTotalBits 11
-#define kBitModelTotal (1 << kNumBitModelTotalBits)
-#define kNumMoveBits 5
-
-#define RC_READ_BYTE (*Buffer++)
-
-#define RC_INIT2 Code = 0; Range = 0xFFFFFFFF; \
-  { int i; for(i = 0; i < 5; i++) { RC_TEST; Code = (Code << 8) | RC_READ_BYTE; }}
-
-#ifdef _LZMA_IN_CB
-
-#define RC_TEST { if (Buffer == BufferLim) \
-  { SizeT size; int result = InCallback->Read(InCallback, &Buffer, &size); if (result != LZMA_RESULT_OK) return result; \
-  BufferLim = Buffer + size; if (size == 0) return LZMA_RESULT_DATA_ERROR; }}
-
-#define RC_INIT Buffer = BufferLim = 0; RC_INIT2
-
-#else
-
-#define RC_TEST { if (Buffer == BufferLim) return LZMA_RESULT_DATA_ERROR; }
-
-#define RC_INIT(buffer, bufferSize) Buffer = buffer; BufferLim = buffer + bufferSize; RC_INIT2
- 
-#endif
-
-#define RC_NORMALIZE if (Range < kTopValue) { RC_TEST; Range <<= 8; Code = (Code << 8) | RC_READ_BYTE; }
-
-#define IfBit0(p) RC_NORMALIZE; bound = (Range >> kNumBitModelTotalBits) * *(p); if (Code < bound)
-#define UpdateBit0(p) Range = bound; *(p) += (kBitModelTotal - *(p)) >> kNumMoveBits;
-#define UpdateBit1(p) Range -= bound; Code -= bound; *(p) -= (*(p)) >> kNumMoveBits;
-
-#define RC_GET_BIT2(p, mi, A0, A1) IfBit0(p) \
-  { UpdateBit0(p); mi <<= 1; A0; } else \
-  { UpdateBit1(p); mi = (mi + mi) + 1; A1; } 
-  
-#define RC_GET_BIT(p, mi) RC_GET_BIT2(p, mi, ; , ;)               
-
-#define RangeDecoderBitTreeDecode(probs, numLevels, res) \
-  { int i = numLevels; res = 1; \
-  do { CProb *p = probs + res; RC_GET_BIT(p, res) } while(--i != 0); \
-  res -= (1 << numLevels); }
-
-
-#define kNumPosBitsMax 4
-#define kNumPosStatesMax (1 << kNumPosBitsMax)
-
-#define kLenNumLowBits 3
-#define kLenNumLowSymbols (1 << kLenNumLowBits)
-#define kLenNumMidBits 3
-#define kLenNumMidSymbols (1 << kLenNumMidBits)
-#define kLenNumHighBits 8
-#define kLenNumHighSymbols (1 << kLenNumHighBits)
-
-#define LenChoice 0
-#define LenChoice2 (LenChoice + 1)
-#define LenLow (LenChoice2 + 1)
-#define LenMid (LenLow + (kNumPosStatesMax << kLenNumLowBits))
-#define LenHigh (LenMid + (kNumPosStatesMax << kLenNumMidBits))
-#define kNumLenProbs (LenHigh + kLenNumHighSymbols) 
-
-
-#define kNumStates 12
-#define kNumLitStates 7
-
-#define kStartPosModelIndex 4
-#define kEndPosModelIndex 14
-#define kNumFullDistances (1 << (kEndPosModelIndex >> 1))
-
-#define kNumPosSlotBits 6
-#define kNumLenToPosStates 4
-
-#define kNumAlignBits 4
-#define kAlignTableSize (1 << kNumAlignBits)
-
-#define kMatchMinLen 2
-
-#define IsMatch 0
-#define IsRep (IsMatch + (kNumStates << kNumPosBitsMax))
-#define IsRepG0 (IsRep + kNumStates)
-#define IsRepG1 (IsRepG0 + kNumStates)
-#define IsRepG2 (IsRepG1 + kNumStates)
-#define IsRep0Long (IsRepG2 + kNumStates)
-#define PosSlot (IsRep0Long + (kNumStates << kNumPosBitsMax))
-#define SpecPos (PosSlot + (kNumLenToPosStates << kNumPosSlotBits))
-#define Align (SpecPos + kNumFullDistances - kEndPosModelIndex)
-#define LenCoder (Align + kAlignTableSize)
-#define RepLenCoder (LenCoder + kNumLenProbs)
-#define Literal (RepLenCoder + kNumLenProbs)
-
-#if Literal != LZMA_BASE_SIZE
-StopCompilingDueBUG
-#endif
-
-int LzmaDecodeProperties(CLzmaProperties *propsRes, const unsigned char *propsData, int size)
-{
-  unsigned char prop0;
-  if (size < LZMA_PROPERTIES_SIZE)
-    return LZMA_RESULT_DATA_ERROR;
-  prop0 = propsData[0];
-  if (prop0 >= (9 * 5 * 5))
-    return LZMA_RESULT_DATA_ERROR;
-  {
-    for (propsRes->pb = 0; prop0 >= (9 * 5); propsRes->pb++, prop0 -= (9 * 5));
-    for (propsRes->lp = 0; prop0 >= 9; propsRes->lp++, prop0 -= 9);
-    propsRes->lc = prop0;
-    /*
-    unsigned char remainder = (unsigned char)(prop0 / 9);
-    propsRes->lc = prop0 % 9;
-    propsRes->pb = remainder / 5;
-    propsRes->lp = remainder % 5;
-    */
-  }
-
-  #ifdef _LZMA_OUT_READ
-  {
-    int i;
-    propsRes->DictionarySize = 0;
-    for (i = 0; i < 4; i++)
-      propsRes->DictionarySize += (UInt32)(propsData[1 + i]) << (i * 8);
-    if (propsRes->DictionarySize == 0)
-      propsRes->DictionarySize = 1;
-  }
-  #endif
-  return LZMA_RESULT_OK;
-}
-
-#define kLzmaStreamWasFinishedId (-1)
-
-int LzmaDecode(CLzmaDecoderState *vs,
-    #ifdef _LZMA_IN_CB
-    ILzmaInCallback *InCallback,
-    #else
-    const unsigned char *inStream, SizeT inSize, SizeT *inSizeProcessed,
-    #endif
-    unsigned char *outStream, SizeT outSize, SizeT *outSizeProcessed)
-{
-  CProb *p = vs->Probs;
-  SizeT nowPos = 0;
-  Byte previousByte = 0;
-  UInt32 posStateMask = (1 << (vs->Properties.pb)) - 1;
-  UInt32 literalPosMask = (1 << (vs->Properties.lp)) - 1;
-  int lc = vs->Properties.lc;
-
-  #ifdef _LZMA_OUT_READ
-  
-  UInt32 Range = vs->Range;
-  UInt32 Code = vs->Code;
-  #ifdef _LZMA_IN_CB
-  const Byte *Buffer = vs->Buffer;
-  const Byte *BufferLim = vs->BufferLim;
-  #else
-  const Byte *Buffer = inStream;
-  const Byte *BufferLim = inStream + inSize;
-  #endif
-  int state = vs->State;
-  UInt32 rep0 = vs->Reps[0], rep1 = vs->Reps[1], rep2 = vs->Reps[2], rep3 = vs->Reps[3];
-  int len = vs->RemainLen;
-  UInt32 globalPos = vs->GlobalPos;
-  UInt32 distanceLimit = vs->DistanceLimit;
-
-  Byte *dictionary = vs->Dictionary;
-  UInt32 dictionarySize = vs->Properties.DictionarySize;
-  UInt32 dictionaryPos = vs->DictionaryPos;
-
-  Byte tempDictionary[4];
-
-  #ifndef _LZMA_IN_CB
-  *inSizeProcessed = 0;
-  #endif
-  *outSizeProcessed = 0;
-  if (len == kLzmaStreamWasFinishedId)
-    return LZMA_RESULT_OK;
-
-  if (dictionarySize == 0)
-  {
-    dictionary = tempDictionary;
-    dictionarySize = 1;
-    tempDictionary[0] = vs->TempDictionary[0];
-  }
-
-  if (len == kLzmaNeedInitId)
-  {
-    {
-      UInt32 numProbs = Literal + ((UInt32)LZMA_LIT_SIZE << (lc + vs->Properties.lp));
-      UInt32 i;
-      for (i = 0; i < numProbs; i++)
-        p[i] = kBitModelTotal >> 1; 
-      rep0 = rep1 = rep2 = rep3 = 1;
-      state = 0;
-      globalPos = 0;
-      distanceLimit = 0;
-      dictionaryPos = 0;
-      dictionary[dictionarySize - 1] = 0;
-      #ifdef _LZMA_IN_CB
-      RC_INIT;
-      #else
-      RC_INIT(inStream, inSize);
-      #endif
-    }
-    len = 0;
-  }
-  while(len != 0 && nowPos < outSize)
-  {
-    UInt32 pos = dictionaryPos - rep0;
-    if (pos >= dictionarySize)
-      pos += dictionarySize;
-    outStream[nowPos++] = dictionary[dictionaryPos] = dictionary[pos];
-    if (++dictionaryPos == dictionarySize)
-      dictionaryPos = 0;
-    len--;
-  }
-  if (dictionaryPos == 0)
-    previousByte = dictionary[dictionarySize - 1];
-  else
-    previousByte = dictionary[dictionaryPos - 1];
-
-  #else /* if !_LZMA_OUT_READ */
-
-  int state = 0;
-  UInt32 rep0 = 1, rep1 = 1, rep2 = 1, rep3 = 1;
-  int len = 0;
-  const Byte *Buffer;
-  const Byte *BufferLim;
-  UInt32 Range;
-  UInt32 Code;
-
-  #ifndef _LZMA_IN_CB
-  *inSizeProcessed = 0;
-  #endif
-  *outSizeProcessed = 0;
-
-  {
-    UInt32 i;
-    UInt32 numProbs = Literal + ((UInt32)LZMA_LIT_SIZE << (lc + vs->Properties.lp));
-    for (i = 0; i < numProbs; i++)
-      p[i] = kBitModelTotal >> 1;
-  }
-  
-  #ifdef _LZMA_IN_CB
-  RC_INIT;
-  #else
-  RC_INIT(inStream, inSize);
-  #endif
-
-  #endif /* _LZMA_OUT_READ */
-
-  while(nowPos < outSize)
-  {
-    CProb *prob;
-    UInt32 bound;
-    int posState = (int)(
-        (nowPos 
-        #ifdef _LZMA_OUT_READ
-        + globalPos
-        #endif
-        )
-        & posStateMask);
-
-    prob = p + IsMatch + (state << kNumPosBitsMax) + posState;
-    IfBit0(prob)
-    {
-      int symbol = 1;
-      UpdateBit0(prob)
-      prob = p + Literal + (LZMA_LIT_SIZE * 
-        (((
-        (nowPos 
-        #ifdef _LZMA_OUT_READ
-        + globalPos
-        #endif
-        )
-        & literalPosMask) << lc) + (previousByte >> (8 - lc))));
-
-      if (state >= kNumLitStates)
-      {
-        int matchByte;
-        #ifdef _LZMA_OUT_READ
-        UInt32 pos = dictionaryPos - rep0;
-        if (pos >= dictionarySize)
-          pos += dictionarySize;
-        matchByte = dictionary[pos];
-        #else
-        matchByte = outStream[nowPos - rep0];
-        #endif
-        do
-        {
-          int bit;
-          CProb *probLit;
-          matchByte <<= 1;
-          bit = (matchByte & 0x100);
-          probLit = prob + 0x100 + bit + symbol;
-          RC_GET_BIT2(probLit, symbol, if (bit != 0) break, if (bit == 0) break)
-        }
-        while (symbol < 0x100);
-      }
-      while (symbol < 0x100)
-      {
-        CProb *probLit = prob + symbol;
-        RC_GET_BIT(probLit, symbol)
-      }
-      previousByte = (Byte)symbol;
-
-      outStream[nowPos++] = previousByte;
-      #ifdef _LZMA_OUT_READ
-      if (distanceLimit < dictionarySize)
-        distanceLimit++;
-
-      dictionary[dictionaryPos] = previousByte;
-      if (++dictionaryPos == dictionarySize)
-        dictionaryPos = 0;
-      #endif
-      if (state < 4) state = 0;
-      else if (state < 10) state -= 3;
-      else state -= 6;
-    }
-    else             
-    {
-      UpdateBit1(prob);
-      prob = p + IsRep + state;
-      IfBit0(prob)
-      {
-        UpdateBit0(prob);
-        rep3 = rep2;
-        rep2 = rep1;
-        rep1 = rep0;
-        state = state < kNumLitStates ? 0 : 3;
-        prob = p + LenCoder;
-      }
-      else
-      {
-        UpdateBit1(prob);
-        prob = p + IsRepG0 + state;
-        IfBit0(prob)
-        {
-          UpdateBit0(prob);
-          prob = p + IsRep0Long + (state << kNumPosBitsMax) + posState;
-          IfBit0(prob)
-          {
-            #ifdef _LZMA_OUT_READ
-            UInt32 pos;
-            #endif
-            UpdateBit0(prob);
-            
-            #ifdef _LZMA_OUT_READ
-            if (distanceLimit == 0)
-            #else
-            if (nowPos == 0)
-            #endif
-              return LZMA_RESULT_DATA_ERROR;
-            
-            state = state < kNumLitStates ? 9 : 11;
-            #ifdef _LZMA_OUT_READ
-            pos = dictionaryPos - rep0;
-            if (pos >= dictionarySize)
-              pos += dictionarySize;
-            previousByte = dictionary[pos];
-            dictionary[dictionaryPos] = previousByte;
-            if (++dictionaryPos == dictionarySize)
-              dictionaryPos = 0;
-            #else
-            previousByte = outStream[nowPos - rep0];
-            #endif
-            outStream[nowPos++] = previousByte;
-            #ifdef _LZMA_OUT_READ
-            if (distanceLimit < dictionarySize)
-              distanceLimit++;
-            #endif
-
-            continue;
-          }
-          else
-          {
-            UpdateBit1(prob);
-          }
-        }
-        else
-        {
-          UInt32 distance;
-          UpdateBit1(prob);
-          prob = p + IsRepG1 + state;
-          IfBit0(prob)
-          {
-            UpdateBit0(prob);
-            distance = rep1;
-          }
-          else 
-          {
-            UpdateBit1(prob);
-            prob = p + IsRepG2 + state;
-            IfBit0(prob)
-            {
-              UpdateBit0(prob);
-              distance = rep2;
-            }
-            else
-            {
-              UpdateBit1(prob);
-              distance = rep3;
-              rep3 = rep2;
-            }
-            rep2 = rep1;
-          }
-          rep1 = rep0;
-          rep0 = distance;
-        }
-        state = state < kNumLitStates ? 8 : 11;
-        prob = p + RepLenCoder;
-      }
-      {
-        int numBits, offset;
-        CProb *probLen = prob + LenChoice;
-        IfBit0(probLen)
-        {
-          UpdateBit0(probLen);
-          probLen = prob + LenLow + (posState << kLenNumLowBits);
-          offset = 0;
-          numBits = kLenNumLowBits;
-        }
-        else
-        {
-          UpdateBit1(probLen);
-          probLen = prob + LenChoice2;
-          IfBit0(probLen)
-          {
-            UpdateBit0(probLen);
-            probLen = prob + LenMid + (posState << kLenNumMidBits);
-            offset = kLenNumLowSymbols;
-            numBits = kLenNumMidBits;
-          }
-          else
-          {
-            UpdateBit1(probLen);
-            probLen = prob + LenHigh;
-            offset = kLenNumLowSymbols + kLenNumMidSymbols;
-            numBits = kLenNumHighBits;
-          }
-        }
-        RangeDecoderBitTreeDecode(probLen, numBits, len);
-        len += offset;
-      }
-
-      if (state < 4)
-      {
-        int posSlot;
-        state += kNumLitStates;
-        prob = p + PosSlot +
-            ((len < kNumLenToPosStates ? len : kNumLenToPosStates - 1) << 
-            kNumPosSlotBits);
-        RangeDecoderBitTreeDecode(prob, kNumPosSlotBits, posSlot);
-        if (posSlot >= kStartPosModelIndex)
-        {
-          int numDirectBits = ((posSlot >> 1) - 1);
-          rep0 = (2 | ((UInt32)posSlot & 1));
-          if (posSlot < kEndPosModelIndex)
-          {
-            rep0 <<= numDirectBits;
-            prob = p + SpecPos + rep0 - posSlot - 1;
-          }
-          else
-          {
-            numDirectBits -= kNumAlignBits;
-            do
-            {
-              RC_NORMALIZE
-              Range >>= 1;
-              rep0 <<= 1;
-              if (Code >= Range)
-              {
-                Code -= Range;
-                rep0 |= 1;
-              }
-            }
-            while (--numDirectBits != 0);
-            prob = p + Align;
-            rep0 <<= kNumAlignBits;
-            numDirectBits = kNumAlignBits;
-          }
-          {
-            int i = 1;
-            int mi = 1;
-            do
-            {
-              CProb *prob3 = prob + mi;
-              RC_GET_BIT2(prob3, mi, ; , rep0 |= i);
-              i <<= 1;
-            }
-            while(--numDirectBits != 0);
-          }
-        }
-        else
-          rep0 = posSlot;
-        if (++rep0 == (UInt32)(0))
-        {
-          /* it's for stream version */
-          len = kLzmaStreamWasFinishedId;
-          break;
-        }
-      }
-
-      len += kMatchMinLen;
-      #ifdef _LZMA_OUT_READ
-      if (rep0 > distanceLimit) 
-      #else
-      if (rep0 > nowPos)
-      #endif
-        return LZMA_RESULT_DATA_ERROR;
-
-      #ifdef _LZMA_OUT_READ
-      if (dictionarySize - distanceLimit > (UInt32)len)
-        distanceLimit += len;
-      else
-        distanceLimit = dictionarySize;
-      #endif
-
-      do
-      {
-        #ifdef _LZMA_OUT_READ
-        UInt32 pos = dictionaryPos - rep0;
-        if (pos >= dictionarySize)
-          pos += dictionarySize;
-        previousByte = dictionary[pos];
-        dictionary[dictionaryPos] = previousByte;
-        if (++dictionaryPos == dictionarySize)
-          dictionaryPos = 0;
-        #else
-        previousByte = outStream[nowPos - rep0];
-        #endif
-        len--;
-        outStream[nowPos++] = previousByte;
-      }
-      while(len != 0 && nowPos < outSize);
-    }
-  }
-  RC_NORMALIZE;
-
-  #ifdef _LZMA_OUT_READ
-  vs->Range = Range;
-  vs->Code = Code;
-  vs->DictionaryPos = dictionaryPos;
-  vs->GlobalPos = globalPos + (UInt32)nowPos;
-  vs->DistanceLimit = distanceLimit;
-  vs->Reps[0] = rep0;
-  vs->Reps[1] = rep1;
-  vs->Reps[2] = rep2;
-  vs->Reps[3] = rep3;
-  vs->State = state;
-  vs->RemainLen = len;
-  vs->TempDictionary[0] = tempDictionary[0];
-  #endif
-
-  #ifdef _LZMA_IN_CB
-  vs->Buffer = Buffer;
-  vs->BufferLim = BufferLim;
-  #else
-  *inSizeProcessed = (SizeT)(Buffer - inStream);
-  #endif
-  *outSizeProcessed = nowPos;
-  return LZMA_RESULT_OK;
-}
diff --git a/target/linux/adm5120/image/lzma-loader/src/LzmaDecode.h b/target/linux/adm5120/image/lzma-loader/src/LzmaDecode.h
deleted file mode 100644
index 2870eeb9c9..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/LzmaDecode.h
+++ /dev/null
@@ -1,113 +0,0 @@
-/* 
-  LzmaDecode.h
-  LZMA Decoder interface
-
-  LZMA SDK 4.40 Copyright (c) 1999-2006 Igor Pavlov (2006-05-01)
-  http://www.7-zip.org/
-
-  LZMA SDK is licensed under two licenses:
-  1) GNU Lesser General Public License (GNU LGPL)
-  2) Common Public License (CPL)
-  It means that you can select one of these two licenses and 
-  follow rules of that license.
-
-  SPECIAL EXCEPTION:
-  Igor Pavlov, as the author of this code, expressly permits you to 
-  statically or dynamically link your code (or bind by name) to the 
-  interfaces of this file without subjecting your linked code to the 
-  terms of the CPL or GNU LGPL. Any modifications or additions 
-  to this file, however, are subject to the LGPL or CPL terms.
-*/
-
-#ifndef __LZMADECODE_H
-#define __LZMADECODE_H
-
-#include "LzmaTypes.h"
-
-/* #define _LZMA_IN_CB */
-/* Use callback for input data */
-
-/* #define _LZMA_OUT_READ */
-/* Use read function for output data */
-
-/* #define _LZMA_PROB32 */
-/* It can increase speed on some 32-bit CPUs, 
-   but memory usage will be doubled in that case */
-
-/* #define _LZMA_LOC_OPT */
-/* Enable local speed optimizations inside code */
-
-#ifdef _LZMA_PROB32
-#define CProb UInt32
-#else
-#define CProb UInt16
-#endif
-
-#define LZMA_RESULT_OK 0
-#define LZMA_RESULT_DATA_ERROR 1
-
-#ifdef _LZMA_IN_CB
-typedef struct _ILzmaInCallback
-{
-  int (*Read)(void *object, const unsigned char **buffer, SizeT *bufferSize);
-} ILzmaInCallback;
-#endif
-
-#define LZMA_BASE_SIZE 1846
-#define LZMA_LIT_SIZE 768
-
-#define LZMA_PROPERTIES_SIZE 5
-
-typedef struct _CLzmaProperties
-{
-  int lc;
-  int lp;
-  int pb;
-  #ifdef _LZMA_OUT_READ
-  UInt32 DictionarySize;
-  #endif
-}CLzmaProperties;
-
-int LzmaDecodeProperties(CLzmaProperties *propsRes, const unsigned char *propsData, int size);
-
-#define LzmaGetNumProbs(Properties) (LZMA_BASE_SIZE + (LZMA_LIT_SIZE << ((Properties)->lc + (Properties)->lp)))
-
-#define kLzmaNeedInitId (-2)
-
-typedef struct _CLzmaDecoderState
-{
-  CLzmaProperties Properties;
-  CProb *Probs;
-
-  #ifdef _LZMA_IN_CB
-  const unsigned char *Buffer;
-  const unsigned char *BufferLim;
-  #endif
-
-  #ifdef _LZMA_OUT_READ
-  unsigned char *Dictionary;
-  UInt32 Range;
-  UInt32 Code;
-  UInt32 DictionaryPos;
-  UInt32 GlobalPos;
-  UInt32 DistanceLimit;
-  UInt32 Reps[4];
-  int State;
-  int RemainLen;
-  unsigned char TempDictionary[4];
-  #endif
-} CLzmaDecoderState;
-
-#ifdef _LZMA_OUT_READ
-#define LzmaDecoderInit(vs) { (vs)->RemainLen = kLzmaNeedInitId; }
-#endif
-
-int LzmaDecode(CLzmaDecoderState *vs,
-    #ifdef _LZMA_IN_CB
-    ILzmaInCallback *inCallback,
-    #else
-    const unsigned char *inStream, SizeT inSize, SizeT *inSizeProcessed,
-    #endif
-    unsigned char *outStream, SizeT outSize, SizeT *outSizeProcessed);
-
-#endif
diff --git a/target/linux/adm5120/image/lzma-loader/src/LzmaTypes.h b/target/linux/adm5120/image/lzma-loader/src/LzmaTypes.h
deleted file mode 100644
index 9c27290757..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/LzmaTypes.h
+++ /dev/null
@@ -1,45 +0,0 @@
-/* 
-LzmaTypes.h 
-
-Types for LZMA Decoder
-
-This file written and distributed to public domain by Igor Pavlov.
-This file is part of LZMA SDK 4.40 (2006-05-01)
-*/
-
-#ifndef __LZMATYPES_H
-#define __LZMATYPES_H
-
-#ifndef _7ZIP_BYTE_DEFINED
-#define _7ZIP_BYTE_DEFINED
-typedef unsigned char Byte;
-#endif 
-
-#ifndef _7ZIP_UINT16_DEFINED
-#define _7ZIP_UINT16_DEFINED
-typedef unsigned short UInt16;
-#endif 
-
-#ifndef _7ZIP_UINT32_DEFINED
-#define _7ZIP_UINT32_DEFINED
-#ifdef _LZMA_UINT32_IS_ULONG
-typedef unsigned long UInt32;
-#else
-typedef unsigned int UInt32;
-#endif
-#endif 
-
-/* #define _LZMA_NO_SYSTEM_SIZE_T */
-/* You can use it, if you don't want <stddef.h> */
-
-#ifndef _7ZIP_SIZET_DEFINED
-#define _7ZIP_SIZET_DEFINED
-#ifdef _LZMA_NO_SYSTEM_SIZE_T
-typedef UInt32 SizeT;
-#else
-#include <stddef.h>
-typedef size_t SizeT;
-#endif
-#endif
-
-#endif
diff --git a/target/linux/adm5120/image/lzma-loader/src/Makefile b/target/linux/adm5120/image/lzma-loader/src/Makefile
deleted file mode 100644
index f23d040cdb..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/Makefile
+++ /dev/null
@@ -1,99 +0,0 @@
-#
-# Makefile for Broadcom BCM947XX boards
-#
-# Copyright 2001-2003, Broadcom Corporation
-# All Rights Reserved.
-#
-# THIS SOFTWARE IS OFFERED "AS IS", AND BROADCOM GRANTS NO WARRANTIES OF ANY
-# KIND, EXPRESS OR IMPLIED, BY STATUTE, COMMUNICATION OR OTHERWISE. BROADCOM
-# SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
-# FOR A SPECIFIC PURPOSE OR NONINFRINGEMENT CONCERNING THIS SOFTWARE.
-#
-# Copyright 2004  Manuel Novoa III <mjn3@codepoet.org>
-#   Modified to support bzip'd kernels.
-#   Of course, it would be better to integrate bunzip capability into CFE.
-#
-# Copyright 2005  Oleg I. Vdovikin <oleg@cs.msu.su>
-#   Cleaned up, modified for lzma support, removed from kernel
-#
-# Copyright 2007 Gabor Juhos <juhosg at openwrt.org>
-#   Modified to support user defined entry point address.
-#   Added support for make targets with different names
-#
-
-LOADADDR	:= 0x80001000
-LZMA_TEXT_START	:= 0x80500000
-LZMA_STARTUP_ORG:= 0
-LOADER_DATA	:=
-CONFIG_PASS_KARGS :=
-CONFIG_BOARD	:=
-
-CC		:= $(CROSS_COMPILE)gcc
-LD		:= $(CROSS_COMPILE)ld
-OBJCOPY		:= $(CROSS_COMPILE)objcopy
-OBJDUMP		:= $(CROSS_COMPILE)objdump
-
-BIN_FLAGS	:= -O binary -R .reginfo -R .note -R .comment -R .mdebug -S
-
-CFLAGS		= -D__KERNEL__ -Wall -Wstrict-prototypes -Wno-trigraphs -Os \
-		  -fno-strict-aliasing -fno-common -fomit-frame-pointer -G 0 -mno-abicalls -fno-pic \
-		  -ffunction-sections -pipe -mlong-calls -fno-common -ffreestanding \
-		  -fhonour-copts \
-		  -mabi=32 -march=mips32 -Wa,-32 -Wa,-march=mips32 -Wa,-mips32 -Wa,--trap
-CFLAGS		+= -DLOADADDR=$(LOADADDR) -D_LZMA_PROB32
-
-ASFLAGS		= $(CFLAGS) -D__ASSEMBLY__ -DLZMA_STARTUP_ORG=$(LZMA_STARTUP_ORG)
-
-LDFLAGS		= -static --gc-sections -no-warn-mismatch
-LDFLAGS		+= -e startup -T loader.lds -Ttext $(LZMA_TEXT_START)
-
-O_FORMAT 	= $(shell $(OBJDUMP) -i | head -2 | grep elf32)
-
-OBJECTS		:= head.o decompress.o board.o printf.o LzmaDecode.o
-
-ifneq ($(strip $(LOADER_DATA)),)
-OBJECTS		+= data.o
-CFLAGS		+= -DLZMA_WRAPPER=1
-else
-CFLAGS		+= -D_LZMA_IN_CB
-endif
-
-ifneq ($(strip $(CONFIG_PASS_KARGS)),)
-CFLAGS		+= -DCONFIG_PASS_KARGS
-endif
-
-BOARD_DEF := $(strip $(CONFIG_BOARD))
-BOARD_DEF := $(shell echo $(BOARD_DEF) | tr a-z A-Z | tr -d -)
-ifneq ($(BOARD_DEF),)
-CFLAGS		+= -DCONFIG_BOARD_$(BOARD_DEF)
-endif
-
-all: loader.bin
-
-# Don't build dependencies, this may die if $(CC) isn't gcc
-dep:
-
-install:
-
-%.o : %.c
-	$(CC) $(CFLAGS) -c -o $@ $<
-
-%.o : %.S
-	$(CC) $(ASFLAGS) -c -o $@ $<
-
-data.o: $(LOADER_DATA)
-	$(LD) -r -b binary --oformat $(O_FORMAT) -T lzma-data.lds -o $@ $<
-
-loader.bin: loader.elf
-	$(OBJCOPY) $(BIN_FLAGS) $< $@
-
-loader.elf: $(OBJECTS)
-	$(LD) $(LDFLAGS) -o $@ $(OBJECTS)
-
-mrproper: clean
-
-clean:
-	rm -f *.elf *.bin *.o
-
-
-
diff --git a/target/linux/adm5120/image/lzma-loader/src/README b/target/linux/adm5120/image/lzma-loader/src/README
deleted file mode 100644
index 16649e9500..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/README
+++ /dev/null
@@ -1,55 +0,0 @@
-/*
- * LZMA compressed kernel decompressor for bcm947xx boards
- *
- * Copyright (C) 2005 by Oleg I. Vdovikin <oleg@cs.msu.su>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- */
-
-The code is intended to decompress kernel, being compressed using lzma utility
-build using 7zip LZMA SDK. This utility is located in the LZMA_Alone directory
-
-decompressor code expects that your .trx file consist of three partitions: 
-
-1) decompressor itself (this is gziped code which pmon/cfe will extract and run
-on boot-up instead of real kernel)
-2) LZMA compressed kernel (both streamed and regular modes are supported now)
-3) Root filesystem
-
-Please be sure to apply the following patch for use this new trx layout (it will
-allow using both new and old trx files for root filesystem lookup code)
-
---- linuz/arch/mips/brcm-boards/bcm947xx/setup.c        2005-01-23 19:24:27.503322896 +0300
-+++ linux/arch/mips/brcm-boards/bcm947xx/setup.c        2005-01-23 19:29:05.237100944 +0300
-@@ -221,7 +221,9 @@
-                /* Try looking at TRX header for rootfs offset */
-                if (le32_to_cpu(trx->magic) == TRX_MAGIC) {
-                        bcm947xx_parts[1].offset = off;
--                       if (le32_to_cpu(trx->offsets[1]) > off)
-+                       if (le32_to_cpu(trx->offsets[2]) > off)
-+                               off = le32_to_cpu(trx->offsets[2]);
-+                       else if (le32_to_cpu(trx->offsets[1]) > off)
-                                off = le32_to_cpu(trx->offsets[1]);
-                        continue;
-                }
-
-
-Revision history:
-	0.02	Initial release
-	0.03	Added Mineharu Takahara <mtakahar@yahoo.com> patch to pass actual
-		output size to decoder (stream mode compressed input is not 
-		a requirement anymore)
-	0.04	Reordered functions using lds script
diff --git a/target/linux/adm5120/image/lzma-loader/src/board.c b/target/linux/adm5120/image/lzma-loader/src/board.c
deleted file mode 100644
index 5ebdbc3b12..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/board.c
+++ /dev/null
@@ -1,185 +0,0 @@
-/*
- * ADM5120 specific board support for LZMA decompressor
- *
- * Copyright (C) 2007-2008 OpenWrt.org
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#include "config.h"
-#include <stddef.h>
-
-#define READREG(r)	*(volatile unsigned int *)(r)
-#define WRITEREG(r,v)	*(volatile unsigned int *)(r) = v
-
-/*
- * INTC definitions
- */
-#define INTC_BASE	0xB2200000
-
-/* INTC registers */
-#define INTC_REG_IRQ_DISABLE	0x0C
-
-/*
- * UART definitions
- */
-#define UART0_BASE	0xB2600000
-#define UART1_BASE	0xB2800000
-/* UART registers */
-#define UART_REG_DATA	0x00	/* Data register */
-#define UART_REG_ECR	0x04	/* Error Clear register */
-#define UART_REG_LCRH	0x08	/* Line Control High register */
-#define UART_REG_LCRM	0x0C	/* Line Control Middle register */
-#define UART_REG_LCRL	0x10	/* Line Control Low register */
-#define UART_REG_CTRL	0x14	/* Control register */
-#define UART_REG_FLAG   0x18	/* Flag register */
-
-/* Control register bits */
-#define UART_CTRL_EN	( 1 << 0 )	/* UART enable */
-
-/* Line Control High register bits */
-#define UART_LCRH_FEN	( 1 << 4 )	/* FIFO enable */
-
-/* Flag register bits */
-#define UART_FLAG_CTS	( 1 << 0 )
-#define UART_FLAG_DSR	( 1 << 1 )
-#define UART_FLAG_DCD	( 1 << 2 )
-#define UART_FLAG_BUSY	( 1 << 3 )
-#define UART_FLAG_RXFE	( 1 << 4 )	/* RX FIFO empty */
-#define UART_FLAG_TXFF	( 1 << 5 )	/* TX FIFO full */
-#define UART_FLAG_RXFF	( 1 << 6 )	/* RX FIFO full */
-#define UART_FLAG_TXFE	( 1 << 7 )	/* TX FIFO empty */
-
-/*
- * SWITCH definitions
- */
-#define SWITCH_BASE	0xB2000000
-
-#define SWITCH_REG_CPUP_CONF	0x0024
-#define SWITCH_REG_PORT_CONF0	0x0028
-
-#define SWITCH_REG_GPIO_CONF0	0x00B8
-#define SWITCH_REG_GPIO_CONF2	0x00BC
-
-#define SWITCH_REG_PORT0_LED	0x0100
-#define SWITCH_REG_PORT1_LED	0x0104
-#define SWITCH_REG_PORT2_LED	0x0108
-#define SWITCH_REG_PORT3_LED	0x010C
-#define SWITCH_REG_PORT4_LED	0x0110
-
-#define SWITCH_PORTS_HW		0x3F		/* Hardware Ports */
-
-/* CPUP_CONF register bits */
-#define CPUP_CONF_DCPUP		( 1 << 0 )	/* Disable CPU port */
-
-/* PORT_CONF0 register bits */
-#define PORT_CONF0_DP_SHIFT	0	/* disable port shift*/
-
-
-/*
- * UART routines
- */
-
-#if defined(CONFIG_USE_UART0)
-#  define UART_READ(r)		READREG(UART0_BASE+(r))
-#  define UART_WRITE(r,v)	WRITEREG(UART0_BASE+(r),(v))
-#else
-#  define UART_READ(r)		READREG(UART1_BASE+(r))
-#  define UART_WRITE(r,v)	WRITEREG(UART1_BASE+(r),(v))
-#endif
-
-static void uart_init(void)
-{
-#if 0
-	unsigned int t;
-
-	/* disable uart */
-	UART_WRITE(UART_REG_CTRL, 0);
-
-	/* keep current baud rate */
-	t = UART_READ(UART_REG_LCRM);
-	UART_WRITE(UART_REG_LCRM, t);
-	t = UART_READ(UART_REG_LCRL);
-	UART_WRITE(UART_REG_LCRL, t);
-
-	/* keep data, stop, and parity bits, but disable FIFO */
-	t = UART_READ(UART_REG_LCRH);
-	t &= ~(UART_LCRH_FEN);
-	UART_WRITE(UART_REG_LCRH, t );
-
-	/* clear error bits */
-	UART_WRITE(UART_REG_ECR, 0xFF);
-
-	/* enable uart, and disable interrupts */
-	UART_WRITE(UART_REG_CTRL, UART_CTRL_EN);
-#endif
-}
-
-/*
- * INTC routines
- */
-
-#define INTC_READ(r)	READREG(INTC_BASE+(r))
-#define INTC_WRITE(r,v)	WRITEREG(INTC_BASE+(r),v)
-
-static void intc_init(void)
-{
-	INTC_WRITE(INTC_REG_IRQ_DISABLE, 0xFFFFFFFF);
-}
-
-/*
- * SWITCH routines
- */
-
-#define SWITCH_READ(r)		READREG(SWITCH_BASE+(r))
-#define SWITCH_WRITE(r,v)	WRITEREG(SWITCH_BASE+(r),v)
-
-static void switch_init(void)
-{
-	/* disable PHYS ports */
-	SWITCH_WRITE(SWITCH_REG_PORT_CONF0,
-	    (SWITCH_PORTS_HW << PORT_CONF0_DP_SHIFT));
-
-	/* disable CPU port */
-	SWITCH_WRITE(SWITCH_REG_CPUP_CONF, CPUP_CONF_DCPUP);
-
-	/* disable GPIO lines */
-	SWITCH_WRITE(SWITCH_REG_GPIO_CONF0, 0);
-	SWITCH_WRITE(SWITCH_REG_GPIO_CONF2, 0);
-
-	/* disable LED lines */
-	SWITCH_WRITE(SWITCH_REG_PORT0_LED, 0);
-	SWITCH_WRITE(SWITCH_REG_PORT1_LED, 0);
-	SWITCH_WRITE(SWITCH_REG_PORT2_LED, 0);
-	SWITCH_WRITE(SWITCH_REG_PORT3_LED, 0);
-	SWITCH_WRITE(SWITCH_REG_PORT4_LED, 0);
-}
-
-void board_putc(int ch)
-{
-	while ((UART_READ(UART_REG_FLAG) & UART_FLAG_TXFE) == 0);
-
-	UART_WRITE(UART_REG_DATA, ch);
-
-	while ((UART_READ(UART_REG_FLAG) & UART_FLAG_TXFE) == 0);
-}
-
-void board_init(void)
-{
-	intc_init();
-	switch_init();
-	uart_init();
-}
diff --git a/target/linux/adm5120/image/lzma-loader/src/config.h b/target/linux/adm5120/image/lzma-loader/src/config.h
deleted file mode 100644
index e5511d16f5..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/config.h
+++ /dev/null
@@ -1,143 +0,0 @@
-#ifndef _CONFIG_H_
-#define _CONFIG_H_
-
-#define FLASH_2M	(2<<20)
-#define FLASH_4M	(4<<20)
-
-/*
- * Cellvision/SparkLAN boards
- */
-
-#if defined(CONFIG_BOARD_CAS630)
-#  define CONFIG_BOARD_NAME	"CAS-630"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_CAS670)
-#  define CONFIG_BOARD_NAME	"CAS-670"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_CAS700)
-#  define CONFIG_BOARD_NAME	"CAS-700"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_CAS790)
-#  define CONFIG_BOARD_NAME	"CAS-790"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_CAS771)
-#  define CONFIG_BOARD_NAME	"CAS-771"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_CAS861)
-#  define CONFIG_BOARD_NAME	"CAS-861"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_NFS101U)
-#  define CONFIG_BOARD_NAME	"NFS-101U"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_NFS202U)
-#  define CONFIG_BOARD_NAME	"NFS-202U"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-/*
- * Compex boards
- */
-#if defined(CONFIG_BOARD_WP54GWRT)
-#  define CONFIG_BOARD_NAME	"WP54G-WRT"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-/*
- * Edimax boards
- */
-#if defined(CONFIG_BOARD_BR6104K)
-#  define CONFIG_BOARD_NAME	"BR-6104K"
-#  define CONFIG_FLASH_SIZE	FLASH_2M
-#endif
-
-#if defined(CONFIG_BOARD_BR6104KP)
-#  define CONFIG_BOARD_NAME	"BR-6104KP"
-#  define CONFIG_FLASH_SIZE	FLASH_2M
-#endif
-
-#if defined(CONFIG_BOARD_BR6104WG)
-#  define CONFIG_BOARD_NAME	"BR-6104WG"
-#  define CONFIG_FLASH_SIZE	FLASH_2M
-#endif
-
-/*
- * Infineon boards
- */
-#if defined(CONFIG_BOARD_EASY5120PATA)
-#  define CONFIG_BOARD_NAME	"EASY 5120P-ATA"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_EASY5120RT)
-#  define CONFIG_BOARD_NAME	"EASY 5120-RT"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_EASY5120WVOIP)
-#  define CONFIG_BOARD_NAME	"EASY 5120-WVOIP"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_EASY83000)
-#  define CONFIG_BOARD_NAME	"EASY 83000"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-/*
- * Motorola boards
- */
-#if defined(CONFIG_BOARD_POWERLINEMUGW)
-#  define CONFIG_BOARD_NAME	"Powerline MU Gateway"
-#  define CONFIG_USE_UART1	1
-#endif
-
-/*
- * OSBRiDGE boards
- */
-#if defined(CONFIG_BOARD_5GXI)
-#  define CONFIG_BOARD_NAME	"OSBRiDGE 5GXi"
-#endif
-
-/*
- * ZyXEL boards
- */
-#if defined(CONFIG_BOARD_P334WT)
-#  define CONFIG_BOARD_NAME	"P-334WT"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-#if defined(CONFIG_BOARD_P335)
-#  define CONFIG_BOARD_NAME	"P-335"
-#  define CONFIG_FLASH_SIZE	FLASH_4M
-#endif
-
-/*
- * Default values
- */
-#ifndef CONFIG_BOARD_NAME
-#  define CONFIG_BOARD_NAME	"ADM5120"
-#endif
-
-#ifndef CONFIG_FLASH_SIZE
-#  define CONFIG_FLASH_SIZE	FLASH_2M
-#endif
-
-#if !defined(CONFIG_USE_UART0) && !defined(CONFIG_USE_UART1)
-#  define CONFIG_USE_UART0
-#endif
-
-#endif /* _CONFIG_H_ */
diff --git a/target/linux/adm5120/image/lzma-loader/src/decompress.c b/target/linux/adm5120/image/lzma-loader/src/decompress.c
deleted file mode 100644
index cd4b8fa605..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/decompress.c
+++ /dev/null
@@ -1,353 +0,0 @@
-/*
- *
- * LZMA compressed kernel decompressor for ADM5120 boards
- *
- * Copyright (C) 2005 by Oleg I. Vdovikin <oleg@cs.msu.su>
- * Copyright (C) 2007-2008 OpenWrt.org
- * Copyright (C) 2007-2008 Gabor Juhos <juhosg@openwrt.org>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- *
- *
- * Please note, this was code based on the bunzip2 decompressor code
- * by Manuel Novoa III  (mjn3@codepoet.org), although the only thing left
- * is an idea and part of original vendor code
- *
- *
- * 12-Mar-2005  Mineharu Takahara <mtakahar@yahoo.com>
- *   pass actual output size to decoder (stream mode
- *   compressed input is not a requirement anymore)
- *
- * 24-Apr-2005 Oleg I. Vdovikin
- *   reordered functions using lds script, removed forward decl
- *
- * 24-Mar-2007 Gabor Juhos
- *   pass original values of the a0,a1,a2,a3 registers to the kernel
- *
- * 19-May-2007 Gabor Juhos
- *   endiannes related cleanups
- *   add support for decompressing an embedded kernel
- *
- */
-
-#include <stddef.h>
-
-#include "config.h"
-#include "printf.h"
-#include "LzmaDecode.h"
-
-#define ADM5120_FLASH_START	0x1fc00000	/* Flash start */
-#define ADM5120_FLASH_END	0x1fe00000	/* Flash end */
-
-#define KSEG0			0x80000000
-#define KSEG1			0xa0000000
-
-#define KSEG1ADDR(a)		((((unsigned)(a)) & 0x1fffffffU) | KSEG1)
-
-#define Index_Invalidate_I	0x00
-#define Index_Writeback_Inv_D   0x01
-
-#define cache_unroll(base,op)	\
-	__asm__ __volatile__(		\
-		".set noreorder;\n"		\
-		".set mips3;\n"			\
-		"cache %1, (%0);\n"		\
-		".set mips0;\n"			\
-		".set reorder\n"		\
-		:				\
-		: "r" (base),			\
-		  "i" (op));
-
-#ifdef LZMA_DEBUG
-#  define DBG(f, a...)	printf(f, ## a)
-#else
-#  define DBG(f, a...)	do {} while (0)
-#endif
-
-static __inline__ void blast_icache(unsigned long size, unsigned long lsize)
-{
-	unsigned long start = KSEG0;
-	unsigned long end = (start + size);
-
-	while(start < end) {
-		cache_unroll(start,Index_Invalidate_I);
-		start += lsize;
-	}
-}
-
-static __inline__ void blast_dcache(unsigned long size, unsigned long lsize)
-{
-	unsigned long start = KSEG0;
-	unsigned long end = (start + size);
-
-	while(start < end) {
-		cache_unroll(start,Index_Writeback_Inv_D);
-		start += lsize;
-	}
-}
-
-#define TRX_MAGIC       0x30524448      /* "HDR0" */
-#define TRX_ALIGN	0x1000
-
-struct trx_header {
-	unsigned int magic;		/* "HDR0" */
-	unsigned int len;		/* Length of file including header */
-	unsigned int crc32;		/* 32-bit CRC from flag_version to end of file */
-	unsigned int flag_version;	/* 0:15 flags, 16:31 version */
-	unsigned int offsets[3];	/* Offsets of partitions from start of header */
-};
-
-struct env_var {
-	char	*name;
-	char	*value;
-};
-
-/* beyound the image end, size not known in advance */
-extern unsigned char workspace[];
-extern void board_init(void);
-
-static CLzmaDecoderState lzma_state;
-
-typedef void (*kernel_entry)(unsigned long reg_a0, unsigned long reg_a1,
-	unsigned long reg_a2, unsigned long reg_a3);
-
-static int decompress_data(CLzmaDecoderState *vs, unsigned char *outStream,
-			UInt32 outSize);
-
-#ifdef CONFIG_PASS_KARGS
-#define ENVV(n,v)	{.name = (n), .value = (v)}
-struct env_var env_vars[] = {
-	ENVV("board_name",	CONFIG_BOARD_NAME),
-	ENVV(NULL, NULL)
-};
-#endif
-
-static void halt(void)
-{
-	printf("\nSystem halted!\n");
-	for(;;);
-}
-
-#if (LZMA_WRAPPER)
-extern unsigned char _lzma_data_start[];
-extern unsigned char _lzma_data_end[];
-
-unsigned char *data;
-unsigned long datalen;
-
-static __inline__ unsigned char get_byte(void)
-{
-	datalen--;
-	return *data++;
-}
-
-static void decompress_init(void)
-{
-	data = _lzma_data_start;
-	datalen = _lzma_data_end - _lzma_data_start;
-}
-
-static int decompress_data(CLzmaDecoderState *vs, unsigned char *outStream,
-			SizeT outSize)
-{
-	SizeT ip, op;
-
-	return LzmaDecode(vs, data, datalen, &ip, outStream, outSize, &op);
-}
-#endif /* LZMA_WRAPPER */
-
-#if !(LZMA_WRAPPER)
-
-#define FLASH_BANK_SIZE	(2<<20)
-
-static unsigned char *flash_base = (unsigned char *) KSEG1ADDR(ADM5120_FLASH_START);
-static unsigned long flash_ofs = 0;
-static unsigned long flash_max = 0;
-static unsigned long flash_ofs_mask = (FLASH_BANK_SIZE-1);
-
-static __inline__ unsigned char get_byte(void)
-{
-	return *(flash_base+flash_ofs++);
-}
-
-static int lzma_read_byte(void *object, const unsigned char **buffer,
-				SizeT *bufferSize)
-{
-	unsigned long len;
-
-	if (flash_ofs >= flash_max)
-		return LZMA_RESULT_DATA_ERROR;
-
-	len = flash_max-flash_ofs;
-
-#if (CONFIG_FLASH_SIZE > FLASH_BANK_SIZE)
-	if (flash_ofs < FLASH_BANK_SIZE) {
-		/* switch to bank 0 */
-		DBG("lzma_read_byte: switch to bank 0\n");
-
-		if (len > FLASH_BANK_SIZE-flash_ofs)
-			len = FLASH_BANK_SIZE-flash_ofs;
-	} else {
-		/* switch to bank 1 */
-		DBG("lzma_read_byte: switch to bank 1\n");
-	}
-#endif
-	DBG("lzma_read_byte: ofs=%08X, len=%08X\n", flash_ofs, len);
-
-	*buffer = flash_base+(flash_ofs & flash_ofs_mask);
-	*bufferSize = len;
-	flash_ofs += len;
-
-	return LZMA_RESULT_OK;
-}
-
-static ILzmaInCallback lzma_callback = {
-	.Read	= lzma_read_byte,
-};
-
-static __inline__ unsigned int read_le32(void *buf)
-{
-	unsigned char *p = buf;
-
-	return ((unsigned int)p[0] + ((unsigned int)p[1] << 8) +
-		((unsigned int)p[2] << 16) +((unsigned int)p[3] << 24));
-}
-
-static void decompress_init(void)
-{
-	struct trx_header *hdr = NULL;
-	unsigned long kofs,klen;
-
-    	printf("Looking for TRX header... ");
-	/* look for trx header, 32-bit data access */
-	for (flash_ofs = 0; flash_ofs < FLASH_BANK_SIZE; flash_ofs += TRX_ALIGN) {
-		if (read_le32(&flash_base[flash_ofs]) == TRX_MAGIC) {
-			hdr = (struct trx_header *)&flash_base[flash_ofs];
-			break;
-		}
-	}
-
-	if (hdr == NULL) {
-		printf("not found!\n");
-		/* no compressed kernel found, halting */
-		halt();
-	}
-
-	/* compressed kernel is in the partition 0 or 1 */
-	kofs = read_le32(&hdr->offsets[1]);
-	if (kofs == 0 || kofs > 65536) {
-		klen = kofs-read_le32(&hdr->offsets[0]);
-		kofs = read_le32(&hdr->offsets[0]);
-	} else {
-		klen = read_le32(&hdr->offsets[2]);
-		if (klen > kofs)
-			klen -= kofs;
-		else
-			klen = read_le32(&hdr->len)-kofs;
-	}
-
-	printf("found at %08X, kernel:%08X len:%08X\n", flash_ofs,
-		kofs, klen);
-
-	flash_ofs += kofs;
-	flash_max = flash_ofs+klen;
-}
-
-static int decompress_data(CLzmaDecoderState *vs, unsigned char *outStream,
-			SizeT outSize)
-{
-	SizeT op;
-
-#if 0
-	vs->Buffer = data;
-	vs->BufferLim = datalen;
-#endif
-
-	return LzmaDecode(vs, &lzma_callback, outStream, outSize, &op);
-}
-#endif /* !(LZMA_WRAPPER) */
-
-/* should be the first function */
-void decompress_entry(unsigned long reg_a0, unsigned long reg_a1,
-	unsigned long reg_a2, unsigned long reg_a3,
-	unsigned long icache_size, unsigned long icache_lsize,
-	unsigned long dcache_size, unsigned long dcache_lsize)
-{
-	unsigned char props[LZMA_PROPERTIES_SIZE];
-	unsigned int i;  /* temp value */
-	SizeT osize; /* uncompressed size */
-	int res;
-
-	board_init();
-
-	printf("\n\nLZMA loader for " CONFIG_BOARD_NAME
-			", Copyright (C) 2007-2008 OpenWrt.org\n\n");
-
-	decompress_init();
-
-	/* lzma args */
-	for (i = 0; i < LZMA_PROPERTIES_SIZE; i++)
-		props[i] = get_byte();
-
-	/* skip rest of the LZMA coder property */
-	/* read the lower half of uncompressed size in the header */
-	osize = ((SizeT)get_byte()) +
-		((SizeT)get_byte() << 8) +
-		((SizeT)get_byte() << 16) +
-		((SizeT)get_byte() << 24);
-
-	/* skip rest of the header (upper half of uncompressed size) */
-	for (i = 0; i < 4; i++)
-		get_byte();
-
-	res = LzmaDecodeProperties(&lzma_state.Properties, props,
-					LZMA_PROPERTIES_SIZE);
-	if (res != LZMA_RESULT_OK) {
-		printf("Incorrect LZMA stream properties!\n");
-		halt();
-	}
-
-	printf("decompressing kernel... ");
-
-	lzma_state.Probs = (CProb *)workspace;
-	res = decompress_data(&lzma_state, (unsigned char *)LOADADDR, osize);
-
-	if (res != LZMA_RESULT_OK) {
-		printf("failed, ");
-		switch (res) {
-		case LZMA_RESULT_DATA_ERROR:
-			printf("data error!\n");
-			break;
-		default:
-			printf("unknown error %d!\n", res);
-		}
-		halt();
-	} else
-		printf("done!\n");
-
-	blast_dcache(dcache_size, dcache_lsize);
-	blast_icache(icache_size, icache_lsize);
-
-	printf("launching kernel...\n\n");
-
-#ifdef CONFIG_PASS_KARGS
-	reg_a0 = 0;
-	reg_a1 = 0;
-	reg_a2 = (unsigned long)env_vars;
-	reg_a3 = 0;
-#endif
-	/* Jump to load address */
-	((kernel_entry) LOADADDR)(reg_a0, reg_a1, reg_a2, reg_a3);
-}
diff --git a/target/linux/adm5120/image/lzma-loader/src/head.S b/target/linux/adm5120/image/lzma-loader/src/head.S
deleted file mode 100644
index 9f82fabdc2..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/head.S
+++ /dev/null
@@ -1,209 +0,0 @@
-/* Copyright 2007 Gabor Juhos <juhosg@freemail.hu>	*/
-/* keep original values of the a0,a1,a2,a3 registers	*/
-/* modifed to support user defined entry point address	*/
-/* Copyright 2005 Oleg I. Vdovikin (oleg@cs.msu.su)	*/
-/* cache manipulation adapted from Broadcom code 	*/
-/* idea taken from original bunzip2 decompressor code	*/
-/* Copyright 2004 Manuel Novoa III (mjn3@codepoet.org)	*/
-/* Licensed under the linux kernel's version of the GPL.*/
-
-#include <asm/asm.h>
-#include <asm/regdef.h>
-
-#define KSEG0		0x80000000
-
-#define C0_STATUS	$12
-#define C0_CAUSE	$13
-#define C0_CONFIG	$16
-#define C0_WATCHLO	$18
-#define C0_WATCHHI	$19
-#define C0_TAGLO	$28
-#define C0_TAGHI	$29
-
-#define	CONF1_DA_SHIFT	7			/* D$ associativity */
-#define CONF1_DA_MASK	0x00000380
-#define CONF1_DA_BASE	1
-#define CONF1_DL_SHIFT	10			/* D$ line size */
-#define CONF1_DL_MASK	0x00001c00
-#define CONF1_DL_BASE	2
-#define CONF1_DS_SHIFT	13			/* D$ sets/way */
-#define CONF1_DS_MASK	0x0000e000
-#define CONF1_DS_BASE	64
-#define CONF1_IA_SHIFT	16			/* I$ associativity */
-#define CONF1_IA_MASK	0x00070000
-#define CONF1_IA_BASE	1
-#define CONF1_IL_SHIFT	19			/* I$ line size */
-#define CONF1_IL_MASK	0x00380000
-#define CONF1_IL_BASE	2
-#define CONF1_IS_SHIFT	22			/* Instruction cache sets/way */
-#define CONF1_IS_MASK	0x01c00000
-#define CONF1_IS_BASE	64
-
-#define Index_Invalidate_I	0x00
-#define Index_Writeback_Inv_D   0x01
-
-	.text
-
-#if (LZMA_STARTUP_ORG)
-	.set	noreorder
-
-	b	startup
-	nop
-
-	.org	LZMA_STARTUP_ORG
-#endif
-
-LEAF(startup)
-	.set noreorder
-	.set mips32
-
-	mtc0	zero, C0_WATCHLO	# clear watch registers
-	mtc0	zero, C0_WATCHHI
-
-	mtc0	zero, C0_CAUSE		# clear before writing status register
-
-	mfc0	t0, C0_STATUS		# get status register
-	li	t1, ~(0xFF01)
-	and	t0, t1			# mask interrupts
-	mtc0	t0, C0_STATUS		# set up status register
-
-	move	t1, ra			# save return address
-	la	t0, __reloc_label	# get linked address of label
-	bal	__reloc_label		# branch and link to label to
-	nop				# get actual address
-__reloc_label:
-	subu	t0, ra, t0		# get reloc_delta
-	move	ra, t1			# restore return address
-
-	beqz	t0, __reloc_end         # if delta is 0 we are in the right place
-	nop
-
-	/* Copy our code to the right place */
-	la	t1, _code_start		# get linked address of _code_start
-	la	t2, _code_end		# get linked address of _code_end
-	addu	t0, t0, t1		# calculate actual address of _code_start
-
-__reloc_copy:
-	lw	t3, 0(t0)
-	sw	t3, 0(t1)
-	add	t1, 4
-	blt	t1, t2, __reloc_copy
-	add	t0, 4
-
-__reloc_end:
-
-	/* At this point we need to invalidate dcache and */
-	/* icache before jumping to new code */
-
-1:	/* Get cache sizes */
-	.set	mips32
-	mfc0	s0,C0_CONFIG,1
-	.set	mips0
-
-	li	s1,CONF1_DL_MASK
-	and	s1,s0
-	beq	s1,zero,nodc
-	nop
-
-	srl	s1,CONF1_DL_SHIFT
-	li	t0,CONF1_DL_BASE
-	sll	s1,t0,s1		/* s1 has D$ cache line size */
-
-	li	s2,CONF1_DA_MASK
-	and	s2,s0
-	srl	s2,CONF1_DA_SHIFT
-	addiu	s2,CONF1_DA_BASE	/* s2 now has D$ associativity */
-
-	li	t0,CONF1_DS_MASK
-	and	t0,s0
-	srl	t0,CONF1_DS_SHIFT
-	li	s3,CONF1_DS_BASE
-	sll	s3,s3,t0		/* s3 has D$ sets per way */
-
-	multu	s2,s3			/* sets/way * associativity */
-	mflo	t0			/* total cache lines */
-
-	multu	s1,t0			/* D$ linesize * lines */
-	mflo	s2			/* s2 is now D$ size in bytes */
-
-	/* Initilize the D$: */
-	mtc0	zero,C0_TAGLO
-	mtc0	zero,C0_TAGHI
-
-	li	t0,KSEG0		/* Just an address for the first $ line */
-	addu	t1,t0,s2		/*  + size of cache == end */
-
-	.set	mips3
-1:	cache	Index_Writeback_Inv_D,0(t0)
-	.set	mips0
-	bne	t0,t1,1b
-	addu	t0,s1
-
-nodc:
-	/* Now we get to do it all again for the I$ */
-
-	move	s3,zero			/* just in case there is no icache */
-	move	s4,zero
-
-	li	t0,CONF1_IL_MASK
-	and	t0,s0
-	beq	t0,zero,noic
-	nop
-
-	srl	t0,CONF1_IL_SHIFT
-	li	s3,CONF1_IL_BASE
-	sll	s3,t0			/* s3 has I$ cache line size */
-
-	li	t0,CONF1_IA_MASK
-	and	t0,s0
-	srl	t0,CONF1_IA_SHIFT
-	addiu	s4,t0,CONF1_IA_BASE	/* s4 now has I$ associativity */
-
-	li	t0,CONF1_IS_MASK
-	and	t0,s0
-	srl	t0,CONF1_IS_SHIFT
-	li	s5,CONF1_IS_BASE
-	sll	s5,t0			/* s5 has I$ sets per way */
-
-	multu	s4,s5			/* sets/way * associativity */
-	mflo	t0			/* s4 is now total cache lines */
-
-	multu	s3,t0			/* I$ linesize * lines */
-	mflo	s4			/* s4 is cache size in bytes */
-
-	/* Initilize the I$: */
-	mtc0	zero,C0_TAGLO
-	mtc0	zero,C0_TAGHI
-
-	li	t0,KSEG0		/* Just an address for the first $ line */
-	addu	t1,t0,s4		/*  + size of cache == end */
-
-	.set	mips3
-1:	cache	Index_Invalidate_I,0(t0)
-	.set	mips0
-	bne	t0,t1,1b
-	addu	t0,s3
-
-noic:
-	/* Setup new "C" stack */
-	la	sp, _stack
-
-	addiu	sp, -32			/* reserve stack for parameters */
-#if 0
-	sw	a0, 0(sp)
-	sw	a1, 4(sp)
-	sw	a2, 8(sp)
-	sw	a3, 12(sp)
-#endif
-	sw	s4, 16(sp)		/* icache size */
-	sw	s3, 20(sp)		/* icache line size */
-	sw	s2, 24(sp)		/* dcache size */
-	sw	s1, 28(sp)		/* dcache line size */
-
-	/* jump to the decompressor routine */
-	la	t0, decompress_entry
-	jr	t0
-	nop
-
-	.set reorder
-END(startup)
diff --git a/target/linux/adm5120/image/lzma-loader/src/loader.lds b/target/linux/adm5120/image/lzma-loader/src/loader.lds
deleted file mode 100644
index bae70fb6ea..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/loader.lds
+++ /dev/null
@@ -1,29 +0,0 @@
-OUTPUT_ARCH(mips)
-SECTIONS {
-	.text : {
-		_code_start = .;
-		*(.text)
-		*(.text.*)
-		*(.rodata)
-		*(.rodata.*)
-		. = ALIGN(16);
-		*(.data.lzma)
-	}
-
-	.data : {
-		*(.data)
-		*(.data.*)
-	}
-	_code_end = .;
-
-	.bss : {
-		*(.bss)
-		*(.bss.*)
-	}
-
-	. = ALIGN(16);
-	. = . + 8192;
-	_stack = .;
-
-	workspace = .;
-}
diff --git a/target/linux/adm5120/image/lzma-loader/src/lzma-data.lds b/target/linux/adm5120/image/lzma-loader/src/lzma-data.lds
deleted file mode 100644
index abf756ba13..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/lzma-data.lds
+++ /dev/null
@@ -1,8 +0,0 @@
-OUTPUT_ARCH(mips)
-SECTIONS {
-	.data.lzma : {
-		_lzma_data_start = .;
-		*(.data)
-		_lzma_data_end = .;
-	}
-}
diff --git a/target/linux/adm5120/image/lzma-loader/src/printf.c b/target/linux/adm5120/image/lzma-loader/src/printf.c
deleted file mode 100644
index 7bb5a86e18..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/printf.c
+++ /dev/null
@@ -1,350 +0,0 @@
-/*
- * Copyright (C) 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-
-#include	"printf.h"
-
-extern void board_putc(int ch);
-
-/* this is the maximum width for a variable */
-#define		LP_MAX_BUF	256
-
-/* macros */
-#define		IsDigit(x)	( ((x) >= '0') && ((x) <= '9') )
-#define		Ctod(x)		( (x) - '0')
-
-/* forward declaration */
-static int PrintChar(char *, char, int, int);
-static int PrintString(char *, char *, int, int);
-static int PrintNum(char *, unsigned long, int, int, int, int, char, int);
-
-/* private variable */
-static const char theFatalMsg[] = "fatal error in lp_Print!";
-
-/* -*-
- * A low level printf() function.
- */
-static void
-lp_Print(void (*output)(void *, char *, int),
-	 void * arg,
-	 char *fmt,
-	 va_list ap)
-{
-
-#define 	OUTPUT(arg, s, l)  \
-  { if (((l) < 0) || ((l) > LP_MAX_BUF)) { \
-       (*output)(arg, (char*)theFatalMsg, sizeof(theFatalMsg)-1); for(;;); \
-    } else { \
-      (*output)(arg, s, l); \
-    } \
-  }
-
-    char buf[LP_MAX_BUF];
-
-    char c;
-    char *s;
-    long int num;
-
-    int longFlag;
-    int negFlag;
-    int width;
-    int prec;
-    int ladjust;
-    char padc;
-
-    int length;
-
-    for(;;) {
-	{
-	    /* scan for the next '%' */
-	    char *fmtStart = fmt;
-	    while ( (*fmt != '\0') && (*fmt != '%')) {
-		fmt ++;
-	    }
-
-	    /* flush the string found so far */
-	    OUTPUT(arg, fmtStart, fmt-fmtStart);
-
-	    /* are we hitting the end? */
-	    if (*fmt == '\0') break;
-	}
-
-	/* we found a '%' */
-	fmt ++;
-
-	/* check for long */
-	if (*fmt == 'l') {
-	    longFlag = 1;
-	    fmt ++;
-	} else {
-	    longFlag = 0;
-	}
-
-	/* check for other prefixes */
-	width = 0;
-	prec = -1;
-	ladjust = 0;
-	padc = ' ';
-
-	if (*fmt == '-') {
-	    ladjust = 1;
-	    fmt ++;
-	}
-
-	if (*fmt == '0') {
-	    padc = '0';
-	    fmt++;
-	}
-
-	if (IsDigit(*fmt)) {
-	    while (IsDigit(*fmt)) {
-		width = 10 * width + Ctod(*fmt++);
-	    }
-	}
-
-	if (*fmt == '.') {
-	    fmt ++;
-	    if (IsDigit(*fmt)) {
-		prec = 0;
-		while (IsDigit(*fmt)) {
-		    prec = prec*10 + Ctod(*fmt++);
-		}
-	    }
-	}
-
-
-	/* check format flag */
-	negFlag = 0;
-	switch (*fmt) {
-	 case 'b':
-	    if (longFlag) {
-		num = va_arg(ap, long int);
-	    } else {
-		num = va_arg(ap, int);
-	    }
-	    length = PrintNum(buf, num, 2, 0, width, ladjust, padc, 0);
-	    OUTPUT(arg, buf, length);
-	    break;
-
-	 case 'd':
-	 case 'D':
-	    if (longFlag) {
-		num = va_arg(ap, long int);
-	    } else {
-		num = va_arg(ap, int);
-	    }
-	    if (num < 0) {
-		num = - num;
-		negFlag = 1;
-	    }
-	    length = PrintNum(buf, num, 10, negFlag, width, ladjust, padc, 0);
-	    OUTPUT(arg, buf, length);
-	    break;
-
-	 case 'o':
-	 case 'O':
-	    if (longFlag) {
-		num = va_arg(ap, long int);
-	    } else {
-		num = va_arg(ap, int);
-	    }
-	    length = PrintNum(buf, num, 8, 0, width, ladjust, padc, 0);
-	    OUTPUT(arg, buf, length);
-	    break;
-
-	 case 'u':
-	 case 'U':
-	    if (longFlag) {
-		num = va_arg(ap, long int);
-	    } else {
-		num = va_arg(ap, int);
-	    }
-	    length = PrintNum(buf, num, 10, 0, width, ladjust, padc, 0);
-	    OUTPUT(arg, buf, length);
-	    break;
-
-	 case 'x':
-	    if (longFlag) {
-		num = va_arg(ap, long int);
-	    } else {
-		num = va_arg(ap, int);
-	    }
-	    length = PrintNum(buf, num, 16, 0, width, ladjust, padc, 0);
-	    OUTPUT(arg, buf, length);
-	    break;
-
-	 case 'X':
-	    if (longFlag) {
-		num = va_arg(ap, long int);
-	    } else {
-		num = va_arg(ap, int);
-	    }
-	    length = PrintNum(buf, num, 16, 0, width, ladjust, padc, 1);
-	    OUTPUT(arg, buf, length);
-	    break;
-
-	 case 'c':
-	    c = (char)va_arg(ap, int);
-	    length = PrintChar(buf, c, width, ladjust);
-	    OUTPUT(arg, buf, length);
-	    break;
-
-	 case 's':
-	    s = (char*)va_arg(ap, char *);
-	    length = PrintString(buf, s, width, ladjust);
-	    OUTPUT(arg, buf, length);
-	    break;
-
-	 case '\0':
-	    fmt --;
-	    break;
-
-	 default:
-	    /* output this char as it is */
-	    OUTPUT(arg, fmt, 1);
-	}	/* switch (*fmt) */
-
-	fmt ++;
-    }		/* for(;;) */
-
-    /* special termination call */
-    OUTPUT(arg, "\0", 1);
-}
-
-
-/* --------------- local help functions --------------------- */
-static int
-PrintChar(char * buf, char c, int length, int ladjust)
-{
-    int i;
-
-    if (length < 1) length = 1;
-    if (ladjust) {
-	*buf = c;
-	for (i=1; i< length; i++) buf[i] = ' ';
-    } else {
-	for (i=0; i< length-1; i++) buf[i] = ' ';
-	buf[length - 1] = c;
-    }
-    return length;
-}
-
-static int
-PrintString(char * buf, char* s, int length, int ladjust)
-{
-    int i;
-    int len=0;
-    char* s1 = s;
-    while (*s1++) len++;
-    if (length < len) length = len;
-
-    if (ladjust) {
-	for (i=0; i< len; i++) buf[i] = s[i];
-	for (i=len; i< length; i++) buf[i] = ' ';
-    } else {
-	for (i=0; i< length-len; i++) buf[i] = ' ';
-	for (i=length-len; i < length; i++) buf[i] = s[i-length+len];
-    }
-    return length;
-}
-
-static int
-PrintNum(char * buf, unsigned long u, int base, int negFlag,
-	 int length, int ladjust, char padc, int upcase)
-{
-    /* algorithm :
-     *  1. prints the number from left to right in reverse form.
-     *  2. fill the remaining spaces with padc if length is longer than
-     *     the actual length
-     *     TRICKY : if left adjusted, no "0" padding.
-     *		    if negtive, insert  "0" padding between "0" and number.
-     *  3. if (!ladjust) we reverse the whole string including paddings
-     *  4. otherwise we only reverse the actual string representing the num.
-     */
-
-    int actualLength =0;
-    char *p = buf;
-    int i;
-
-    do {
-	int tmp = u %base;
-	if (tmp <= 9) {
-	    *p++ = '0' + tmp;
-	} else if (upcase) {
-	    *p++ = 'A' + tmp - 10;
-	} else {
-	    *p++ = 'a' + tmp - 10;
-	}
-	u /= base;
-    } while (u != 0);
-
-    if (negFlag) {
-	*p++ = '-';
-    }
-
-    /* figure out actual length and adjust the maximum length */
-    actualLength = p - buf;
-    if (length < actualLength) length = actualLength;
-
-    /* add padding */
-    if (ladjust) {
-	padc = ' ';
-    }
-    if (negFlag && !ladjust && (padc == '0')) {
-	for (i = actualLength-1; i< length-1; i++) buf[i] = padc;
-	buf[length -1] = '-';
-    } else {
-	for (i = actualLength; i< length; i++) buf[i] = padc;
-    }
-
-
-    /* prepare to reverse the string */
-    {
-	int begin = 0;
-	int end;
-	if (ladjust) {
-	    end = actualLength - 1;
-	} else {
-	    end = length -1;
-	}
-
-	while (end > begin) {
-	    char tmp = buf[begin];
-	    buf[begin] = buf[end];
-	    buf[end] = tmp;
-	    begin ++;
-	    end --;
-	}
-    }
-
-    /* adjust the string pointer */
-    return length;
-}
-
-static void printf_output(void *arg, char *s, int l)
-{
-    int i;
-
-    // special termination call
-    if ((l==1) && (s[0] == '\0')) return;
-
-    for (i=0; i< l; i++) {
-	board_putc(s[i]);
-	if (s[i] == '\n') board_putc('\r');
-    }
-}
-
-void printf(char *fmt, ...)
-{
-    va_list ap;
-    va_start(ap, fmt);
-    lp_Print(printf_output, 0, fmt, ap);
-    va_end(ap);
-}
diff --git a/target/linux/adm5120/image/lzma-loader/src/printf.h b/target/linux/adm5120/image/lzma-loader/src/printf.h
deleted file mode 100644
index 9b1c1df232..0000000000
--- a/target/linux/adm5120/image/lzma-loader/src/printf.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/*
- * Copyright (C) 2001 MontaVista Software Inc.
- * Author: Jun Sun, jsun@mvista.com or jsun@junsun.net
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- *
- */
-
-#ifndef _printf_h_
-#define _printf_h_
-
-#include <stdarg.h>
-void printf(char *fmt, ...);
-
-#endif /* _printf_h_ */