update libertas driver

SVN-Revision: 13447

1 files changed, 417 insertions, 0 deletions

diff --git a/package/libertas/src/README b/package/libertas/src/README
index d860fc3757..2706a42695 100644
--- a/package/libertas/src/README
+++ b/package/libertas/src/README
@@ -28,6 +28,423 @@ DRIVER LOADING
 
 		insmod usb8388.ko [fw_name=usb8388.bin]
 
+=====================
+IWPRIV COMMAND
+=====================
+
+NAME
+	This manual describes the usage of private commands used in Marvell WLAN
+	Linux Driver. All the commands available in Wlanconfig will not be available
+	in the iwpriv.
+
+SYNOPSIS
+	iwpriv <ethX> <command> [sub-command] ...
+
+	iwpriv ethX setregioncode <n>
+	iwpriv ethX getregioncode
+
+Version 5 Command:
+	iwpriv ethX ledgpio <n>
+
+BT Commands:
+	The blinding table (BT) contains a list of mac addresses that will be,
+	by default, ignored by the firmware. It is also possible to invert this
+	behavior so that we will ignore all traffic except for the portion
+	coming from mac addresess in the list. It is primarily used for
+	debugging and testing networks.  It can be edited and inspected with
+	the following commands:
+
+	iwpriv ethX bt_reset
+	iwpriv ethX bt_add <mac_address>
+	iwpriv ethX bt_del <mac_address>
+	iwpriv ethX bt_list <id>
+	iwpriv ethX bt_get_invert <n>
+	iwpriv ethX bt_set_invert <n>
+
+FWT Commands:
+	The forwarding table (FWT) is a feature used to manage mesh network
+	routing in the firmware.  The FWT is essentially a routing table that
+	associates a destination mac address (da) with a next hop receiver
+	address (ra).  The FWT can be inspected and edited with the following
+	iwpriv commands, which are described in greater detail below.
+	Eventually, the table will be automatically maintained by a custom
+	routing protocol.
+
+	NOTE: FWT commands replace the previous DFT commands.  What were the DFT
+	commands?, you might ask.  They were an earlier API to the firmware that
+	implemented a simple MAC-layer forwarding mechanism.  In the unlikely
+	event that you were using these commands, you must migrate to the new
+	FWT commands which can be used to achieve the same functionality.
+
+	iwpriv ethX fwt_add [parameters]
+	iwpriv ethX fwt_del [parameters]
+	iwpriv ethX fwt_lookup [parameters]
+	iwpriv ethX fwt_list [parameters]
+	iwpriv ethX fwt_list_route [parameters]
+	iwpriv ethX fwt_list_neigh [parameters]
+	iwpriv ethX fwt_reset [parameters]
+	iwpriv ethX fwt_cleanup
+	iwpriv ethX fwt_time
+
+MESH Commands:
+
+	The MESH commands are used to configure various features of the mesh
+	routing protocol.  The following commands are supported:
+
+	iwpriv ethX mesh_get_ttl
+	iwpriv ethX mesh_set_ttl ttl
+	iwpriv ethX mesh_get_bcastr rate
+	iwpriv ethX mesh_set_bcastr rate
+	iwpriv ethX get_rreq_delay
+	iwpriv ethX set_rreq_delay delay
+	iwpriv ethX get_route_exp
+	iwpriv ethX set_route_exp time
+	iwpriv ethX get_link_costs
+	iwpriv ethX set_link_costs "cost54 cost36 cost11 cost1"
+
+DESCRIPTION
+	Those commands are used to send additional commands to the Marvell WLAN
+	card via the Linux device driver.
+
+	The ethX parameter specifies the network device that is to be used to
+		perform this command on. it could be eth0, eth1 etc.
+
+setregioncode
+	This command is used to set the region code in the station.
+	where value is 'region code' for various regions like
+	USA FCC, Canada IC, Spain, France, Europe ETSI,	Japan ...
+
+	Usage:
+		iwpriv ethX setregioncode 0x10: set region code to USA (0x10).
+
+getregioncode
+	This command is used to get the region code information set in the
+	station.
+
+ledgpio
+	This command is used to set/get LEDs.
+
+	iwpriv ethX ledgpio <LEDs>
+		will set the corresponding LED for the GPIO Line.
+
+	iwpriv ethX ledgpio
+		will give u which LEDs are Enabled.
+
+	Usage:
+		iwpriv eth1 ledgpio 1 0 2 1 3 4
+			will enable
+			LED 1 -> GPIO 0
+			LED 2 -> GPIO 1
+			LED 3 -> GPIO 4
+
+		iwpriv eth1 ledgpio
+			shows LED information in the format as mentioned above.
+
+	Note: LED0 is invalid
+	Note: Maximum Number of LEDs are 16.
+
+bcn_control
+	This command is used to enable disable beacons. This can also be used
+	to set beacon interval.
+
+	Usage:
+		iwpriv ethX bcn_control [enable] [beacon_interval]
+
+		enable: 0 to disable beacon. 1 to enable beacon.
+		beacon_interval: 20 - 1000ms.
+
+	Examples:
+		1. iwpriv ethX bcn_control
+		   Returns (x, y), where x if 1, indicates beacon is enabled, y 
+		   beacon period.
+		2. iwpriv ethX bcn_control 0
+		   Turns off beacon transmission.
+		3. iwpriv ethX bcn_control 1 500
+		   Enable beacon with beacon interval 500ms.
+		
+
+ledbhv
+      Command iwpriv mshX ledbhv can be used to change default LEDs behaviors.
+      A given LED behavior can be on, off or blinking. The duty/cycle can be set
+      when behavior is programmed as blinking.
+
+      Usage:
+
+        1. To get default LED behavior
+           iwpriv mshX ledbhv <firmware state>
+
+        2. To set or change default LED behavior
+           iwpriv mshX ledbhv <firmware state> <lednum> <behavior> <arg>
+
+        firmware state: The following are some of the relevant states.
+          00: disconnected 
+          01: firmware is scanning
+          02: firmware is connected and awake
+          03: firmware is sleeping
+          04: connected deep sleep
+          06: firmware disconnected link lost 
+          07: firmware disconnected disassociated
+          09: data transfer while firmware is associated and not scanning. 
+              If firmware is already in this state, LED behavior does not change 
+              on this data transfer.
+          10: firmware idle, not scanning, not disconnected or disassociated.
+
+        lednum: 1 or 2 for first and second LED.
+  
+        behavior: 0 for steady ON, 1 - steady off and 2- blinking.
+
+        arg: It is used when behavior is 2 to set duty and cycle. It is defined as 
+             (duty << 4 | cycle). Here duty could be 0..4 and cycle 0..5 for 34, 
+             74, 149, 298, 596, 1192 ms respectively.
+
+      Examples:
+
+       1. To get default behavior for scan
+          iwpriv mshX ledbhv 1
+
+       2. To get default behavior while data transfer
+          iwpriv mshX ledbhv 9      
+ 
+       3. To turn off LED 2
+          iwpriv mshX ledbhv 2 2 1 0
+          iwpriv mshX ledbhv 10 2 1 0
+
+       4. To enable LED 2 and blink LED 1 while data transfer.
+          iwpriv mshX ledbhv 9 2 0 0
+          iwpriv mshX ledbhv 9 1 2 4
+
+       5. To change duty cycle of LED 2 during data transfer
+          iwpriv mshX ledbhv 9 2 2 36
+
+       6. To turn ON LED 2 when firmware is disassociated/disconnected.
+          iwpriv mshX ledbhv 0 2 0 0
+	
+
+fwt_add
+	This command is used to insert an entry into the FWT table. The list of
+	parameters must follow the following structure:
+
+	iwpriv ethX fwt_add da ra [metric dir rate ssn dsn hopcount ttl expiration sleepmode snr]
+
+	The parameters between brackets are optional, but they must appear in
+	the order specified.  For example, if you want to specify the metric,
+	you must also specify the dir, ssn, and dsn but you need not specify the
+	hopcount, expiration, sleepmode, or snr.  Any unspecified parameters
+	will be assigned the defaults specified below.
+
+	The different parameters are:-
+		da		-- DA MAC address in the form 00:11:22:33:44:55
+		ra		-- RA MAC address in the form 00:11:22:33:44:55
+		metric		-- route metric (cost: smaller-metric routes are
+				   preferred, default is 0)
+		dir		-- direction (1 for direct, 0 for reverse,
+				   default is 1)
+		rate		-- data rate used for transmission to the RA,
+				   as specified for the rateadapt command,
+				   default is 3 (11Mbps)
+		ssn		-- Source Sequence Number (time at the RA for
+				   reverse routes.  Default is 0)
+		dsn		-- Destination Sequence Number (time at the DA
+				   for direct routes.  Default is 0)
+		hopcount	-- hop count (currently unused, default is 0)
+		ttl		-- TTL (Only used in reverse entries)
+		expiration	-- entry expiration (in ticks, where a tick is
+				   1024us, or ~ 1ms. Use 0 for an indefinite
+				   entry, default is 0)
+		sleepmode	-- RA's sleep mode (currently unused, default is
+				   0)
+		snr		-- SNR in the link to RA (currently unused,
+				   default is 0)
+
+	The command does not return anything.
+
+fwt_del
+	This command is used to remove an entry to the FWT table. The list of
+	parameters must follow the following structure:
+
+		iwpriv ethX fwt_del da ra [dir]
+
+	where the different parameters are:-
+		da		-- DA MAC address (in the form "00:11:22:33:44:55")
+		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
+		dir		-- direction (1 for direct, 0 for reverse,
+				   default is 1)
+
+	The command does not return anything.
+
+fwt_lookup
+	This command is used to get the best route in the FWT table to a given
+	host. The only parameter is the MAC address of the host that is being
+	looked for.
+
+		iwpriv ethX fwt_lookup da
+
+	where:-
+		da		-- DA MAC address (in the form "00:11:22:33:44:55")
+
+	The command returns an output string identical to the one returned by
+	fwt_list described below.
+
+
+fwt_list
+	This command is used to list a route from the FWT table. The only
+	parameter is the index into the table. If you want to list all the
+	routes in a table, start with index=0, and keep listing until you get a
+	"(null)" string.  Note that the indicies may change as the fwt is
+	updated.  It is expected that most users will not use fwt_list directly,
+	but that a utility similar to the traditional route command will be used
+	to invoke fwt_list over and over.
+
+		iwpriv ethX fwt_list index
+
+	The output is a string of the following form:
+
+		da ra valid metric dir rate ssn dsn hopcount ttl expiration
+		sleepmode snr precursor
+
+	where the different fields are:-
+		da		-- DA MAC address (in the form "00:11:22:33:44:55")
+		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
+		valid		-- whether the route is valid (0 if not valid)
+		metric		-- route metric (cost: smaller-metric routes are preferred)
+		dir		-- direction (1 for direct, 0 for reverse)
+		rate		-- data rate used for transmission to the RA,
+				   as specified for the rateadapt command
+		ssn		-- Source Sequence Number (time at the RA for reverse routes)
+		dsn		-- Destination Sequence Number (time at the DA for direct routes)
+		hopcount	-- hop count (currently unused)
+		ttl		-- TTL (only used in reverse entries)
+		expiration	-- entry expiration (in ticks, where a tick is 1024us, or ~ 1ms. Use 0 for an indefinite entry)
+		sleepmode	-- RA's sleep mode (currently unused)
+		snr		-- SNR in the link to RA (currently unused)
+		precursor	-- predecessor in direct routes
+
+fwt_list_route
+	This command is equivalent to fwt_list.
+
+fwt_list_neigh
+	This command is used to list a neighbor from the FWT table. The only
+	parameter is the neighbor ID. If you want to list all the neighbors in a
+	table, start with nid=0, and keep incrementing nid until you get a
+	"(null)" string.  Note that the nid from a fwt_list_route command can be
+	used as an input to this command.  Also note that this command is meant
+	mostly for debugging.  It is expected that users will use fwt_lookup.
+	One important reason for this is that the neighbor id may change as the
+	neighbor table is altered.
+
+		iwpriv ethX fwt_list_neigh nid
+
+	The output is a string of the following form:
+
+		ra sleepmode snr references
+
+	where the different fields are:-
+		ra		-- RA MAC address (in the form "00:11:22:33:44:55")
+		sleepmode	-- RA's sleep mode (currently unused)
+		snr		-- SNR in the link to RA (currently unused)
+		references	-- RA's reference counter
+
+fwt_reset
+	This command is used to reset the FWT table, getting rid of all the
+	entries. There are no input parameters.
+
+		iwpriv ethX fwt_reset
+
+	The command does not return anything.
+
+fwt_cleanup
+	This command is used to perform user-based garbage recollection. The
+	FWT table is checked, and all the entries that are expired or invalid
+	are cleaned. Note that this is exported to the driver for debugging
+	purposes, as garbage collection is also fired by the firmware when in
+	space problems. There are no input parameters.
+
+		iwpriv ethX fwt_cleanup
+
+	The command does returns the number of invalid/expired routes deleted.
+
+fwt_time
+	This command returns a card's internal time representation.  It is this
+	time that is used to represent the expiration times of FWT entries.  The
+	number is not consistent from card to card; it is simply a timer count.
+	The fwt_time command is used to inspect the timer so that expiration
+	times reported by fwt_list can be properly interpreted.
+
+		iwpriv ethX fwt_time
+
+mesh_get_ttl
+
+	The mesh ttl is the number of hops a mesh packet can traverse before it
+	is dropped.  This parameter is used to prevent infinite loops in the
+	mesh network.  The value returned by this function is the ttl assigned
+	to all mesh packets.  Currently there is no way to control the ttl on a
+	per packet or per socket basis.
+
+	iwpriv ethX mesh_get_ttl
+
+mesh_set_ttl ttl
+
+	Set the ttl.  The argument must be between 0 and 255.
+
+	iwpriv ethX mesh_set_ttl <ttl>
+
+mesh_get_bcastr
+
+	Shows the rate index used for mesh broadcast and multicast packets.
+	Rates are expressed in 2 * Mb/s, ie 11Mb/s is 22, 5.5Mb/s is 11, etc.
+
+	iwpriv ethX mesh_get_bcastr rate
+
+mesh_set_bcastr rate
+
+	Sets the rate index for mesh broadcast and muticast packets. Rates are
+	expressed in expressed in 2 * Mb/s, ie 11Mb/s is 22, 5.5Mb/s is 11, etc.
+
+	iwpriv ethX mesh_set_bcastr rate
+
+get_rreq_delay
+
+	Shows the delay to forward a RREQ frame. This delay allows the node to
+	forward just the best route in case the same RREQ arrives to the node
+	through different routes. The argument is shown in 1/100 seconds.
+
+	iwpriv ethX get_rreq_delay
+
+set_rreq_delay delay
+
+	Sets the RREQ forward delay. The delay is interpreted as 1/100 seconds.
+
+	iwpriv ethX set_rreq_delay delay
+
+get_route_exp
+
+	Shows the mesh route expiration time, in seconds.
+
+	iwpriv ethX get_route_exp
+
+set_route_exp time
+
+	Gets the mesh route, expiration time, in seconds.
+
+	iwpriv ethX set_route_exp time
+
+get_link_costs
+
+	Gets the mesh hop base cost for each used rate. The output gives us the
+	base cost for hops at 54Mbps, 36Mbps, 11Mbps and 1Mbps, in that order.
+	The base cost gets divided by a battery state factor to get the actual
+	cost. A cost of 0 means that rate is deactivated.
+
+	iwpriv ethX get_link_costs
+
+set_link_costs "cost54 cost36 cost11 cost1"
+
+	Sets the mesh hop base cost for the used speeds. The input parameter
+	will specify the cost for hops at 54Mbps, 36Mbps, 11Mbps and 1Mbps, in
+	that order. A cost of 0 will disable a specific rate.
+
+	iwpriv ethX set_link_costs "cost54 cost36 cost11 cost1"
+
 =========================
 ETHTOOL
 =========================