diff options
| author | David Bauer <mail@david-bauer.net> | 2018-03-29 00:32:38 +0200 |
|---|---|---|
| committer | Mathias Kresin <dev@kresin.me> | 2018-04-13 07:48:19 +0200 |
| commit | 970f1914be3f299fb302ca74a214589397000858 (patch) | |
| tree | 5b7a7d0ffe4b0cc774ca5b027351bbdcf1472986 /package/firmware/ipq-wifi/Makefile | |
| parent | be6e28b516be2701bb734b11fe39d739207e9186 (diff) | |
| download | upstream-970f1914be3f299fb302ca74a214589397000858.tar.gz upstream-970f1914be3f299fb302ca74a214589397000858.tar.bz2 upstream-970f1914be3f299fb302ca74a214589397000858.zip | |
ipq40xx: add support for Netgear EX6100v2/EX6150v2
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
Diffstat (limited to 'package/firmware/ipq-wifi/Makefile')
| -rw-r--r-- | package/firmware/ipq-wifi/Makefile | 3 |
1 files changed, 2 insertions, 1 deletions
diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 7cc6478452..0df5078d78 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -13,7 +13,7 @@ endef define Build/Compile endef -ALLWIFIBOARDS:=8dev_jalapeno asus_rt-ac58u avm_fritzbox-4040 glinet_gl-b1300 meraki_mr33 +ALLWIFIBOARDS:=8dev_jalapeno asus_rt-ac58u avm_fritzbox-4040 glinet_gl-b1300 meraki_mr33 netgear_ex61x0v2 ALLWIFIPACKAGES:=$(foreach BOARD,$(ALLWIFIBOARDS),ipq-wifi-$(BOARD)) define Package/ipq-wifi-default @@ -52,5 +52,6 @@ $(eval $(call generate-ipq-wifi-package,asus_rt-ac58u,board-asus_rt-ac58u.bin,AS $(eval $(call generate-ipq-wifi-package,avm_fritzbox-4040,board-avm_fritzbox-4040.bin,AVM FRITZ!Box 4040)) $(eval $(call generate-ipq-wifi-package,glinet_gl-b1300,board-glinet_gl-b1300.bin,GL.iNet GL-B1300)) $(eval $(call generate-ipq-wifi-package,meraki_mr33,board-meraki_mr33.bin,Cisco Meraki MR33)) +$(eval $(call generate-ipq-wifi-package,netgear_ex61x0v2,board-netgear_ex61x0v2.bin,Netgear EX61x0v2)) $(foreach PACKAGE,$(ALLWIFIPACKAGES),$(eval $(call BuildPackage,$(PACKAGE)))) |