uboot-kirkwood: add Zyxel NSA325 uboot

add uboot for NSA325

Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>

1 files changed, 709 insertions, 0 deletions

diff --git a/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch b/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch
new file mode 100644
index 0000000000..bb179b95a6
--- /dev/null
+++ b/package/boot/uboot-kirkwood/patches/008-nsa325-uboot-generic.patch
@@ -0,0 +1,709 @@
+diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
+index 819bd3b..6a2d578 100644
+--- a/arch/arm/mach-kirkwood/Kconfig
++++ b/arch/arm/mach-kirkwood/Kconfig
+@@ -55,6 +55,9 @@ config TARGET_NSA310
+ config TARGET_NSA310S
+	bool "Zyxel NSA310S"
+
++config TARGET_NSA325
++	bool "Zyxel NSA325 board"
++
+ endchoice
+
+ config SYS_SOC
+@@ -77,5 +80,6 @@ source "board/Seagate/goflexhome/Kconfig"
+ source "board/Seagate/nas220/Kconfig"
+ source "board/zyxel/nsa310/Kconfig"
+ source "board/zyxel/nsa310s/Kconfig"
++source "board/zyxel/nsa325/Kconfig"
+
+ endif
+diff --git a/board/zyxel/nsa325/Kconfig b/board/zyxel/nsa325/Kconfig
+new file mode 100644
+index 0000000..1fe5ead
+--- /dev/null
++++ b/board/zyxel/nsa325/Kconfig
+@@ -0,0 +1,12 @@
++if TARGET_NSA325
++
++config SYS_BOARD
++	default "nsa325"
++
++config SYS_VENDOR
++	default "zyxel"
++
++config SYS_CONFIG_NAME
++	default "nsa325"
++
++endif
+diff --git a/board/zyxel/nsa325/MAINTAINERS b/board/zyxel/nsa325/MAINTAINERS
+new file mode 100644
+index 0000000..130b4d9
+--- /dev/null
++++ b/board/zyxel/nsa325/MAINTAINERS
+@@ -0,0 +1,6 @@
++NSA325 BOARD
++M:	Alberto Bursi <alberto.bursi@outlook.it>
++S:	Maintained
++F:	board/zyxel/nsa325/
++F:	include/configs/nsa325.h
++F:	configs/nsa325_defconfig
+diff --git a/board/zyxel/nsa325/Makefile b/board/zyxel/nsa325/Makefile
+new file mode 100644
+index 0000000..4ee953b
+--- /dev/null
++++ b/board/zyxel/nsa325/Makefile
+@@ -0,0 +1,13 @@
++#
++# (C) Copyright 2015 bodhi <mibodhi@gmail.com>
++#
++# Based on
++# (C) Copyright 2009
++# Marvell Semiconductor <www.marvell.com>
++# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
++#
++# SPDX-License-Identifier:	GPL-2.0+
++#
++
++obj-y	:= nsa325.o
++
+diff --git a/board/zyxel/nsa325/kwbimage.cfg b/board/zyxel/nsa325/kwbimage.cfg
+new file mode 100644
+index 0000000..5a27d38
+--- /dev/null
++++ b/board/zyxel/nsa325/kwbimage.cfg
+@@ -0,0 +1,78 @@
++# Copyright (C) 2015 bodhi <mibodhi@gmail.com>
++#
++# Extracted from Zyxel GPL source for u-boot-1.1.4_NSA325v2
++#
++# See file CREDITS for list of people who contributed to this
++# project.
++#
++# This program is free software; you can redistribute it and/or
++# modify it under the terms of the GNU General Public License as
++# published by the Free Software Foundation; either version 2 of
++# the License, or (at your option) any later version.
++#
++# This program is distributed in the hope that it will be useful,
++# but WITHOUT ANY WARRANTY; without even the implied warranty of
++# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++# GNU General Public License for more details.
++#
++# You should have received a copy of the GNU General Public License
++# along with this program; if not, write to the Free Software
++# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++# MA 02110-1301 USA
++#
++# Refer docs/README.kwimage for more details about how-to configure
++# and create kirkwood boot image
++#
++
++# Boot Media configurations
++#BOOT_FROM	uart
++BOOT_FROM       nand
++NAND_ECC_MODE   default
++NAND_PAGE_SIZE  0x0800
++
++# SOC registers configuration using bootrom header extension
++# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
++
++# Configure RGMII-0 interface pad voltage to 1.8V
++DATA 0xFFD100e0 0x1b1b1b9b
++
++#Dram initalization
++DATA 0xFFD01400 0x4301503E      # DDR Configuration register
++DATA 0xFFD01404 0xB9843000      # DDR Controller Control Low
++DATA 0xFFD01408 0x33137777      # DDR Timing (Low)
++DATA 0xFFD0140C 0x16000C55      # DDR Timing (High)
++DATA 0xFFD01410 0x04000000      # DDR Address Control
++DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
++DATA 0xFFD01418 0x00000000	#  DDR Operation
++DATA 0xFFD0141C 0x00000672	#  DDR Mode
++DATA 0xFFD01420 0x00000004	#  DDR Extended Mode
++DATA 0xFFD01424 0x0000F14F	#  DDR Controller Control High
++DATA 0xFFD01428 0x000D6720	# DDR3 ODT Read Timing
++DATA 0xFFD0147C 0x0000B571	# DDR2 ODT Write Timing
++DATA 0xFFD01504 0x1FFFFFF1      # CS[0]n Size
++DATA 0xFFD01508 0x20000000      # CS[1]n Base address to 512Mb
++DATA 0xFFD0150C 0x1FFFFFF4      # CS[1]n Size 512Mb Window enabled for CS1
++DATA 0xFFD01514 0x00000000      # CS[2]n Size, window disabled
++DATA 0xFFD0151C 0x00000000      # CS[3]n Size, window disabled
++DATA 0xFFD01494 0x00120000      #  DDR ODT Control (Low)
++DATA 0xFFD01498 0x00000000      #  DDR ODT Control (High)
++DATA 0xFFD0149C 0x0000E803      # CPU ODT Control
++
++DATA 0xFFD015D0 0x00000630
++DATA 0xFFD015D4 0x00000046
++DATA 0xFFD015D8 0x00000008
++DATA 0xFFD015DC 0x00000000
++DATA 0xFFD015E0 0x00000023
++DATA 0xFFD015E4 0x00203C18
++DATA 0xFFD01620 0x00384800
++DATA 0xFFD01480 0x00000001
++DATA 0xFFD20134 0x66666666
++DATA 0xFFD20138 0x00066666
++
++#Disable nsa325 hardware watchdog to allow successful kwbooting
++DATA 0xFFD10100 0x00004000 # set GPIO 14 to high to disable the watchdog
++DATA 0xFFD10104 0xFFFFBFFF # set GPIO 14 to output (to block any other input to it)
++
++# End of Header extension
++DATA 0x0 0x0
++
+diff --git a/board/zyxel/nsa325/nsa325.c b/board/zyxel/nsa325/nsa325.c
+new file mode 100644
+index 0000000..4cd1c0f
+--- /dev/null
++++ b/board/zyxel/nsa325/nsa325.c
+@@ -0,0 +1,265 @@
++/*
++ * Copyright (C) 2015 bodhi <mibodhi@gmail.com>
++ *
++ * Based on
++ * Copyright (C) 2014  Jason Plum <jplum@archlinuxarm.org>
++ *
++ * Based on nsa320.c originall written by
++ * Copyright (C) 2012  Peter Schildmann <linux@schildmann.info>
++ *
++ * Based on guruplug.c originally written by
++ * Siddarth Gore <gores@marvell.com>
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#include <common.h>
++#include <miiphy.h>
++#include <asm/arch/soc.h>
++#include <asm/arch/mpp.h>
++#include <asm/arch/cpu.h>
++#include <asm/gpio.h>
++#include <asm/io.h>
++#include "nsa325.h"
++#include <asm/arch/gpio.h>
++
++DECLARE_GLOBAL_DATA_PTR;
++
++int board_early_init_f(void)
++{
++	/*
++	 * default gpio configuration
++	 * There are maximum 64 gpios controlled through 2 sets of registers
++	 * the below configuration configures mainly initial LED status
++	 */
++	mvebu_config_gpio(NSA325_VAL_LOW, NSA325_VAL_HIGH,
++		       NSA325_OE_LOW, NSA325_OE_HIGH);
++
++	/* Multi-Purpose Pins Functionality configuration */
++	/* (all LEDs & power off active high) */
++	u32 kwmpp_config[] = {
++		MPP0_NF_IO2,
++		MPP1_NF_IO3,
++		MPP2_NF_IO4,
++		MPP3_NF_IO5,
++		MPP4_NF_IO6,
++		MPP5_NF_IO7,
++		MPP6_SYSRST_OUTn,
++		MPP7_GPO,
++		MPP8_TW_SDA,		/* PCF8563 RTC chip   */
++		MPP9_TW_SCK,		/* connected to TWSI  */
++		MPP10_UART0_TXD,
++		MPP11_UART0_RXD,
++		MPP12_GPO,		/* HDD2 LED (green)   */
++		MPP13_GPIO,		/* HDD2 LED (red)     */
++		MPP14_GPIO,		/* MCU DATA pin (in)  */
++		MPP15_GPIO,		/* USB LED (green)    */
++		MPP16_GPIO,		/* MCU CLK pin (out)  */
++		MPP17_GPIO,		/* MCU ACT pin (out)  */
++		MPP18_NF_IO0,
++		MPP19_NF_IO1,
++		MPP20_GPIO,
++		MPP21_GPIO,		/* USB power          */
++		MPP22_GPIO,
++		MPP23_GPIO,
++		MPP24_GPIO,
++		MPP25_GPIO,
++		MPP26_GPIO,
++		MPP27_GPIO,
++		MPP28_GPIO,		/* SYS LED (green)    */
++		MPP29_GPIO,		/* SYS LED (orange)   */
++		MPP30_GPIO,
++		MPP31_GPIO,
++		MPP32_GPIO,
++		MPP33_GPIO,
++		MPP34_GPIO,
++		MPP35_GPIO,
++		MPP36_GPIO,		/* reset button       */
++		MPP37_GPIO,		/* copy button        */
++		MPP38_GPIO,		/* VID B0             */
++		MPP39_GPIO,		/* COPY LED (green)   */
++		MPP40_GPIO,		/* COPY LED (red)     */
++		MPP41_GPIO,		/* HDD1 LED (green)   */
++		MPP42_GPIO,		/* HDD1 LED (red)     */
++		MPP43_GPIO,		/* HTP pin            */
++		MPP44_GPIO,		/* buzzer             */
++		MPP45_GPIO,		/* VID B1             */
++		MPP46_GPIO,		/* power button       */
++		MPP47_GPIO,		/* HDD2 power         */
++		MPP48_GPIO,		/* power off          */
++		0
++	};
++	kirkwood_mpp_conf(kwmpp_config, NULL);
++	return 0;
++}
++
++int board_init(void)
++{
++
++	/* address of boot parameters */
++	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
++
++	/* This disables the hardware watchdog in the mcu on this board. */
++	kw_gpio_set_valid(14, 1);
++	kw_gpio_direction_output(14, 0);
++	kw_gpio_set_value(14, 1);
++
++	return 0;
++}
++
++#ifdef CONFIG_RESET_PHY_R
++/* Configure and enable MV88E1318 PHY */
++void reset_phy(void)
++{
++	u16 reg;
++	u16 devadr;
++	char *name = "egiga0";
++
++	if (miiphy_set_current_dev(name))
++		return;
++
++	/* command to read PHY dev address */
++	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
++		printf("Err..%s could not read PHY dev address\n",
++			__FUNCTION__);
++		return;
++	}
++
++	/* Set RGMII delay */
++	miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_MAC_CTRL_PG);
++	miiphy_read(name, devadr, MV88E1318_MAC_CTRL_REG, &reg);
++	reg |= (MV88E1318_RGMII_RXTM_CTRL | MV88E1318_RGMII_TXTM_CTRL);
++	miiphy_write(name, devadr, MV88E1318_MAC_CTRL_REG, reg);
++	miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
++
++	/* reset the phy */
++	miiphy_reset(name, devadr);
++
++	/* The ZyXEL NSA325 uses the 88E1310S Alaska (interface identical to 88E1318) */
++	/* and has an MCU attached to the LED[2] via tristate interrupt */
++	reg = 0;
++
++	/* switch to LED register page */
++	miiphy_write(name, devadr, MV88E1318_PGADR_REG, MV88E1318_LED_PG);
++	/* read out LED polarity register */
++	miiphy_read(name, devadr, MV88E1318_LED_POL_REG, &reg);
++	/* clear 4, set 5 - LED2 low, tri-state */
++	reg &= ~(MV88E1318_LED2_4);
++	reg |= (MV88E1318_LED2_5);
++	/* write back LED polarity register */
++	miiphy_write(name, devadr, MV88E1318_LED_POL_REG, reg);
++	/* jump back to page 0, per the PHY chip documenation. */
++	miiphy_write(name, devadr, MV88E1318_PGADR_REG, 0);
++
++	/* Set the phy back to auto-negotiation mode. Onboard mcu sets it as 10Mbits/s on poweroff for WoL function */
++	miiphy_write(name, devadr, 0x4, 0x1e1);
++	miiphy_write(name, devadr, 0x9, 0x300);
++	/* Downshift */
++	miiphy_write(name, devadr, 0x10, 0x3860);
++	miiphy_write(name, devadr, 0x0, 0x9140);
++
++	printf("MV88E1318 PHY initialized on %s\n", name);
++
++}
++#endif /* CONFIG_RESET_PHY_R */
++
++#ifdef CONFIG_SHOW_BOOT_PROGRESS
++void show_boot_progress(int val)
++{
++	struct kwgpio_registers *gpio0 = (struct kwgpio_registers *)MVEBU_GPIO0_BASE;
++	u32 dout0 = readl(&gpio0->dout);
++	u32 blen0 = readl(&gpio0->blink_en);
++
++	struct kwgpio_registers *gpio1 = (struct kwgpio_registers *)MVEBU_GPIO1_BASE;
++	u32 dout1 = readl(&gpio1->dout);
++	u32 blen1 = readl(&gpio1->blink_en);
++
++	switch (val) {
++	case BOOTSTAGE_ID_DECOMP_IMAGE:
++		writel(blen0 & ~(SYS_GREEN_LED | SYS_ORANGE_LED), &gpio0->blink_en);
++		writel((dout0 & ~SYS_GREEN_LED) | SYS_ORANGE_LED, &gpio0->dout);
++		break;
++	case BOOTSTAGE_ID_RUN_OS:
++		writel(dout0 & ~SYS_ORANGE_LED, &gpio0->dout);
++		writel(blen0 | SYS_GREEN_LED, &gpio0->blink_en);
++		break;
++	case BOOTSTAGE_ID_NET_START:
++		writel(dout1 & ~COPY_RED_LED, &gpio1->dout);
++		writel((blen1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->blink_en);
++		break;
++	case BOOTSTAGE_ID_NET_LOADED:
++		writel(blen1 & ~(COPY_RED_LED | COPY_GREEN_LED), &gpio1->blink_en);
++		writel((dout1 & ~COPY_RED_LED) | COPY_GREEN_LED, &gpio1->dout);
++		break;
++	case -BOOTSTAGE_ID_NET_NETLOOP_OK:
++	case -BOOTSTAGE_ID_NET_LOADED:
++		writel(dout1 & ~COPY_GREEN_LED, &gpio1->dout);
++		writel((blen1 & ~COPY_GREEN_LED) | COPY_RED_LED, &gpio1->blink_en);
++		break;
++	default:
++		if (val < 0) {
++			/* error */
++			printf("Error occured, error code = %d\n", -val);
++			writel(dout0 & ~SYS_GREEN_LED, &gpio0->dout);
++			writel(blen0 | SYS_ORANGE_LED, &gpio0->blink_en);
++		}
++		break;
++	}
++}
++#endif
++
++#if defined(CONFIG_KIRKWOOD_GPIO)
++/* Return GPIO button status */
++/*
++un-pressed:
++ gpio-36 (Reset Button ) in hi (act lo) - IRQ edge (clear )
++ gpio-37 (Copy Button  ) in hi (act lo) - IRQ edge (clear )
++ gpio-46 (Power Button ) in lo (act hi) - IRQ edge (clear )
++pressed
++ gpio-36 (Reset Button ) in lo (act hi) - IRQ edge (clear )
++ gpio-37 (Copy Button  ) in lo (act hi) - IRQ edge (clear )
++ gpio-46 (Power Button ) in hi (act lo) - IRQ edge (clear )
++*/
++
++static int
++do_read_button(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
++{
++	if (strcmp(argv[1], "power") == 0) {
++			kw_gpio_set_valid(BTN_POWER, GPIO_INPUT_OK);
++			kw_gpio_direction_input(BTN_POWER);
++			return !kw_gpio_get_value(BTN_POWER);
++	}
++	else if (strcmp(argv[1], "reset") == 0)
++		return kw_gpio_get_value(BTN_RESET);
++	else if (strcmp(argv[1], "copy") == 0)
++		return kw_gpio_get_value(BTN_COPY);
++	else
++		return -1;
++}
++
++
++U_BOOT_CMD(button, 2, 0, do_read_button,
++	   "Return GPIO button status 0=off 1=on",
++	   "- button power|reset|copy: test buttons states\n"
++);
++
++#endif
++
+diff --git a/board/zyxel/nsa325/nsa325.h b/board/zyxel/nsa325/nsa325.h
+new file mode 100644
+index 0000000..996653e
+--- /dev/null
++++ b/board/zyxel/nsa325/nsa325.h
+@@ -0,0 +1,77 @@
++/*
++ * Copyright (C) 2014  Jason Plum <jplum@archlinuxarm.org>
++ *
++ * Based on nsa320.h originall written by
++ * Copyright (C) 2012  Peter Schildmann <linux@schildmann.info>
++ *
++ * Based on guruplug.h originally written by
++ * Siddarth Gore <gores@marvell.com>
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#ifndef __NSA325_H
++#define __NSA325_H
++
++/* low GPIO's */
++#define HDD2_GREEN_LED		(1 << 12)
++#define HDD2_RED_LED		(1 << 13)
++#define USB_GREEN_LED		(1 << 15)
++#define USB_POWER		(1 << 21)
++#define SYS_GREEN_LED		(1 << 28)
++#define SYS_ORANGE_LED		(1 << 29)
++
++#define PIN_USB_GREEN_LED	15
++#define PIN_USB_POWER		21
++
++#define NSA325_OE_LOW		(~(HDD2_GREEN_LED | HDD2_RED_LED | \
++				   USB_GREEN_LED | USB_POWER | \
++				   SYS_GREEN_LED | SYS_ORANGE_LED))
++#define NSA325_VAL_LOW		(SYS_GREEN_LED | USB_POWER)
++
++/* high GPIO's */
++#define COPY_GREEN_LED		(1 << 7)
++#define COPY_RED_LED		(1 << 8)
++#define HDD1_GREEN_LED		(1 << 9)
++#define HDD1_RED_LED		(1 << 10)
++#define HDD2_POWER          (1 << 15)
++#define WATCHDOG_SIGNAL     (1 << 14)
++
++#define NSA325_OE_HIGH		(~(COPY_GREEN_LED | COPY_RED_LED | \
++				   HDD1_GREEN_LED | HDD1_RED_LED | HDD2_POWER | WATCHDOG_SIGNAL ))
++#define NSA325_VAL_HIGH		(WATCHDOG_SIGNAL | HDD2_POWER)
++
++/* PHY related */
++#define MV88E1318_PGADR_REG		22
++#define MV88E1318_MAC_CTRL_PG	2
++#define MV88E1318_MAC_CTRL_REG	21
++#define MV88E1318_RGMII_TXTM_CTRL	(1 << 4)
++#define MV88E1318_RGMII_RXTM_CTRL	(1 << 5)
++#define MV88E1318_LED_PG        3
++#define MV88E1318_LED_POL_REG	17
++#define MV88E1318_LED2_4	    (1 << 4)
++#define MV88E1318_LED2_5	    (1 << 5)
++
++#define BTN_POWER				46
++#define BTN_RESET				36
++#define BTN_COPY				37
++
++#endif /* __NSA325_H */
+diff --git a/configs/nsa325_defconfig b/configs/nsa325_defconfig
+new file mode 100644
+index 0000000..48e09cc
+--- /dev/null
++++ b/configs/nsa325_defconfig
+@@ -0,0 +1,18 @@
++CONFIG_ARM=y
++CONFIG_KIRKWOOD=y
++CONFIG_TARGET_NSA325=y
++CONFIG_BOOTDELAY=3
++CONFIG_SYS_PROMPT="NSA325> "
++# CONFIG_CMD_IMLS is not set
++# CONFIG_CMD_FLASH is not set
++CONFIG_SYS_NS16550=y
++CONFIG_CMD_FDT=y
++CONFIG_OF_LIBFDT=y
++CONFIG_CMD_SETEXPR=y
++CONFIG_CMD_DHCP=y
++CONFIG_CMD_NAND=y
++CONFIG_CMD_PING=y
++CONFIG_CMD_USB=y
++CONFIG_USB=y
++CONFIG_CMD_FAT=y
++CONFIG_USB_STORAGE=y
+\ No newline at end of file
+diff --git a/include/configs/nsa325.h b/include/configs/nsa325.h
+new file mode 100644
+index 0000000..e5a8e2a
+--- /dev/null
++++ b/include/configs/nsa325.h
+@@ -0,0 +1,170 @@
++/*
++ * (C) Copyright 2016 bodhi <mibodhi@gmail.com>
++ *
++ * Based on
++ * Copyright (C) 2014 Jason Plum <jplum@archlinuxarm.org>
++ * Based on
++ * Copyright (C) 2012  Peter Schildmann <linux@schildmann.info>
++ *
++ * Based on guruplug.h originally written by
++ * Siddarth Gore <gores@marvell.com>
++ * (C) Copyright 2009
++ * Marvell Semiconductor <www.marvell.com>
++ *
++ * See file CREDITS for list of people who contributed to this
++ * project.
++ *
++ * This program is free software; you can redistribute it and/or
++ * modify it under the terms of the GNU General Public License as
++ * published by the Free Software Foundation; either version 2 of
++ * the License, or (at your option) any later version.
++ *
++ * This program is distributed in the hope that it will be useful,
++ * but WITHOUT ANY WARRANTY; without even the implied warranty of
++ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
++ * GNU General Public License for more details.
++ *
++ * You should have received a copy of the GNU General Public License
++ * along with this program; if not, write to the Free Software
++ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
++ * MA 02110-1301 USA
++ */
++
++#ifndef _CONFIG_NSA325_H
++#define _CONFIG_NSA325_H
++
++/*
++ * Version number information
++ */
++#define CONFIG_IDENT_STRING	"\nZyXEL NSA325 2-Bay Power Media Server"
++
++/*
++ * High Level Configuration Options (easy to change)
++ */
++#define CONFIG_FEROCEON_88FR131	1	/* CPU Core subversion */
++#define CONFIG_KIRKWOOD		1	/* SOC Family Name */
++#define CONFIG_KW88F6281	1	/* SOC Name */
++
++#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
++
++/*
++ * Misc Configuration Options
++ */
++#define CONFIG_SHOW_BOOT_PROGRESS 1	/* boot progess display (LED's) */
++
++/*
++ * Commands configuration
++ */
++#define CONFIG_SYS_NO_FLASH             /* Declare no flash (NOR/SPI) */
++#define CONFIG_SYS_MVFS                 /* Picks up Filesystem from mv-common.h */
++#define CONFIG_CMD_DHCP
++#define CONFIG_CMD_ENV
++#define CONFIG_CMD_IDE
++#define CONFIG_CMD_MII
++#define CONFIG_CMD_NAND
++#define CONFIG_CMD_PING
++#define CONFIG_CMD_USB
++#define CONFIG_CMD_DATE
++#define CONFIG_SYS_LONGHELP
++#define CONFIG_PREBOOT
++#define CONFIG_SYS_HUSH_PARSER
++#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
++
++/*
++ * mv-common.h should be defined after CMD configs since it used them
++ * to enable certain macros
++ */
++#include "mv-common.h"
++
++#undef CONFIG_SYS_PROMPT	/* previously defined in mv-common.h */
++#define CONFIG_SYS_PROMPT	"NSA325> "	/* Command Prompt */
++
++/*
++ *  Environment variables configurations
++ */
++#ifdef CONFIG_CMD_NAND
++#define CONFIG_ENV_IS_IN_NAND		1
++#define CONFIG_ENV_SECT_SIZE		0x20000		/* 128K */
++#else
++#define CONFIG_ENV_IS_NOWHERE		1		/* if env in SDRAM */
++#endif
++/*
++ * max 4k env size is enough, but in case of nand
++ * it has to be rounded to sector size
++ */
++#define CONFIG_ENV_SIZE			0x20000		/* 128k */
++#define CONFIG_ENV_ADDR			0xc0000
++#define CONFIG_ENV_OFFSET		0xc0000	/* env starts here */
++
++/*
++ * Default environment variables
++ */
++#define CONFIG_BOOTCOMMAND \
++	"ubi part ubi; " \
++	"ubi read 0x800000 kernel; " \
++	"bootm 0x800000"
++
++#define CONFIG_MTDPARTS \
++	"mtdparts=orion_nand:" \
++	"0x0c0000(uboot)," \
++	"0x80000(uboot_env)," \
++	"0x7ec0000(ubi)\0"
++
++#define CONFIG_EXTRA_ENV_SETTINGS \
++	"console=console=ttyS0,115200\0"	\
++	"mtdids=nand0=orion_nand\0"		\
++	"mtdparts="CONFIG_MTDPARTS		\
++	"bootargs_root=\0"
++
++/*
++ * Ethernet Driver configuration
++ */
++#ifdef CONFIG_CMD_NET
++#define CONFIG_MVGBE_PORTS		{1, 0}	/* enable port 0 only */
++#define CONFIG_PHY_BASE_ADR		0x1
++#define CONFIG_PHY_GIGE
++#define CONFIG_NETCONSOLE
++#endif /* CONFIG_CMD_NET */
++
++/*
++ * SATA Driver configuration
++ */
++#ifdef CONFIG_MVSATA_IDE
++#define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
++#define CONFIG_SYS_ATA_IDE1_OFFSET      MV_SATA_PORT1_OFFSET
++#endif /* CONFIG_MVSATA_IDE */
++
++/*
++ * File system
++ */
++#define CONFIG_CMD_EXT2
++#define CONFIG_CMD_EXT4
++#define CONFIG_CMD_FAT
++#define CONFIG_CMD_JFFS2
++#define CONFIG_JFFS2_NAND
++#define CONFIG_JFFS2_LZO
++#define CONFIG_CMD_UBI
++#define CONFIG_CMD_UBIFS
++#define CONFIG_RBTREE
++#define CONFIG_MTD_DEVICE               /* needed for mtdparts commands */
++#define CONFIG_MTD_PARTITIONS
++#define CONFIG_CMD_MTDPARTS
++#define CONFIG_LZO
++
++/*
++ * EFI partition
++ */
++#define CONFIG_EFI_PARTITION
++
++/*
++ *  Date Time
++ */
++#ifdef CONFIG_CMD_DATE
++#define CONFIG_RTC_MV
++#define CONFIG_CMD_SNTP
++#define CONFIG_CMD_DNS
++#endif /* CONFIG_CMD_DATE */
++
++#define CONFIG_KIRKWOOD_GPIO /* Enable GPIO Support */
++
++#endif /* _CONFIG_NSA325_H */