kirkwood: Replace dtses with upstream accepted

DTSes from of three boards was sent and accpeted upstream. Let's use
backport patches with small OpenWrt tweak like other upstream stuff.

List of boards:
  - Zyxel NSA310S
  - Endian 4i Edge 200
  - Ctera C-200 V1

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>

9 files changed, 1020 insertions, 792 deletions

diff --git a/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-4i-edge-200.dts b/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
deleted file mode 100644
index 8e6c198c5e..0000000000
--- a/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
+++ /dev/null
@@ -1,218 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Endian 4i Edge 200 Board Description
- * Note: Endian UTM Mini is hardware clone of Endian Edge 200
- * Copyright 2021 Pawel Dembicki <paweldembicki@gmail.com>
- */
-
-/dts-v1/;
-
-#include "kirkwood.dtsi"
-#include "kirkwood-6281.dtsi"
-
-/ {
-	model = "Endian 4i Edge 200";
-	compatible = "endian,4i-edge-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x20000000>;
-	};
-
-	aliases {
-		led-boot = &led_status_green;
-		led-failsafe = &led_status_orange;
-		led-running = &led_status_green;
-		led-upgrade = &led_status_orange;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8";
-		stdout-path = &uart0;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-0 = <&pmx_led49 &pmx_led35 &pmx_led34>;
-		pinctrl-names = "default";
-
-		led_status_green: status_green {
-			label = "green:status";
-			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
-		};
-
-		led_status_orange: status_orange {
-			label = "orange:status";
-			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-		};
-
-		sdcard {
-			label = "orange:sdcard";
-			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-		};
-	};
-};
-
-&eth0 {
-	status = "okay";
-};
-
-&eth0port {
-	speed = <1000>;
-	duplex = <1>;
-};
-
-&eth1 {
-	status = "okay";
-};
-
-&eth1port {
-	phy-handle = <&ethphyb>;
-};
-
-&mdio {
-	status = "okay";
-
-	ethphyb: ethernet-phy@b {
-		reg = <0x0b>;
-
-		marvell,reg-init =
-			/* link-activity, bi-color mode 4 */
-			<3 0x10 0xfff0 0xf>; /* Reg 3,16 <- 0xzzzf */
-	};
-
-	switch0: switch@11 {
-		compatible = "marvell,mv88e6085";
-		reg = <0x11>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				label = "port1";
-			};
-
-			port@1 {
-				reg = <1>;
-				label = "port2";
-			};
-
-			port@2 {
-				reg = <2>;
-				label = "port3";
-			};
-
-			port@3 {
-				reg = <3>;
-				label = "port4";
-			};
-
-			port@5 {
-				reg = <5>;
-				phy-mode = "rgmii-id";
-				ethernet = <&eth0port>;
-
-				fixed-link {
-					speed = <1000>;
-					full-duplex;
-				};
-			};
-		};
-	};
-};
-
-&nand {
-	status = "okay";
-	pinctrl-0 = <&pmx_nand>;
-	pinctrl-names = "default";
-
-	partition@0 {
-		label = "u-boot";
-		reg = <0x00000000 0x000a0000>;
-		read-only;
-	};
-
-	partition@a0000 {
-		label = "u-boot-env";
-		reg = <0x000a0000 0x00060000>;
-		read-only;
-	};
-
-	partition@100000 {
-		label = "kernel";
-		reg = <0x00100000 0x00400000>;
-	};
-
-	partition@500000 {
-		label = "ubi";
-		reg = <0x00500000 0x1fb00000>;
-	};
-};
-
-&pciec {
-	status = "okay";
-};
-
-&pcie0 {
-	status = "okay";
-};
-
-&pinctrl {
-	pinctrl-0 = <&pmx_sysrst>;
-	pinctrl-names = "default";
-
-	pmx_sysrst: pmx-sysrst {
-		marvell,pins = "mpp6";
-		marvell,function = "sysrst";
-	};
-
-	pmx_sdio_cd: pmx-sdio-cd {
-		marvell,pins = "mpp28";
-		marvell,function = "gpio";
-	};
-
-	pmx_led34: pmx_led34 {
-		marvell,pins = "mpp34";
-		marvell,function = "gpio";
-	};
-
-	pmx_led35: pmx_led35 {
-		marvell,pins = "mpp35";
-		marvell,function = "gpio";
-	};
-
-	pmx_led49: pmx_led49 {
-		marvell,pins = "mpp49";
-		marvell,function = "gpio";
-	};
-};
-
-&rtc {
-	status = "okay";
-};
-
-&sata_phy0 {
-	status = "disabled";
-};
-
-&sata_phy1 {
-	status = "disabled";
-};
-
-&sdio {
-	pinctrl-0 = <&pmx_sdio_cd>;
-	pinctrl-names = "default";
-	status = "okay";
-	cd-gpios = <&gpio0 28 9>;
-};
-
-&uart0 {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-};
diff --git a/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-c200-v1.dts b/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-c200-v1.dts
deleted file mode 100644
index 9ff73382b3..0000000000
--- a/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-c200-v1.dts
+++ /dev/null
@@ -1,303 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Ctera C200 V1 Board Description
- * Copyright 2021 Pawel Dembicki <paweldembicki@gmail.com>
- */
-
-/dts-v1/;
-
-#include "kirkwood.dtsi"
-#include "kirkwood-6281.dtsi"
-
-/ {
-	model = "Ctera C200 V1";
-	compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
-	aliases {
-		led-boot = &led_status_green;
-		led-failsafe = &led_status_red;
-		led-running = &led_status_green;
-		led-upgrade = &led_status_red;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200";
-		stdout-path = &uart0;
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x00000000 0x20000000>;
-	};
-
-	keys {
-		compatible = "gpio-keys";
-		pinctrl-0 = <&pmx_buttons>;
-		pinctrl-names = "default";
-
-		power {
-			label = "Power Button";
-			linux,code = <KEY_POWER>;
-			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
-		};
-
-		reset {
-			label = "Reset Button";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
-		};
-
-		usb1 {
-			label = "USB1 Button";
-			linux,code = <BTN_0>;
-			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
-		};
-
-		usb2 {
-			label = "USB2 Button";
-			linux,code = <BTN_1>;
-			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	gpio-poweroff {
-		compatible = "gpio-poweroff";
-		pinctrl-0 = <&pmx_poweroff>;
-		pinctrl-names = "default";
-		gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-0 = <&pmx_leds>;
-		pinctrl-names = "default";
-
-		led_status_green: status-green {
-			label = "green:status";
-			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
-		};
-
-		led_status_red: status-red {
-			label = "red:status";
-			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
-		};
-
-		cloud-blue {
-			label = "blue:cloud";
-			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
-		};
-
-		disk1-green {
-			label = "green:disk1";
-			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "ata1";
-		};
-
-		disk1-red {
-			label = "red:disk1";
-			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
-		};
-
-		disk2-green {
-			label = "green:disk2";
-			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "ata2";
-		};
-
-		disk2-red {
-			label = "red:disk2";
-			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
-		};
-
-		disk-fail-green {
-			label = "green:disk-fail";
-			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
-		};
-
-		disk-fail-red {
-			label = "red:disk-fail";
-			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
-		};
-
-		usb1-green {
-			label = "green:usb1";
-			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "usbport";
-			trigger-sources = <&hub_port2>;
-		};
-
-		usb1-red {
-			label = "red:usb1";
-			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
-		};
-
-		usb2-green {
-			label = "green:usb2";
-			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "usbport";
-			trigger-sources = <&hub_port1>;
-		};
-
-		usb2-red {
-			label = "red:usb2";
-			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&eth0 {
-	status = "okay";
-};
-
-&eth0port {
-	phy-handle = <&ethphy9>;
-};
-
-&i2c0 {
-	status = "okay";
-
-	rtc@30 {
-		compatible = "s35390a";
-		reg = <0x30>;
-	};
-
-	lm63@4c {
-		compatible = "national,lm63";
-		reg = <0x4c>;
-	};
-};
-
-&mdio {
-	status = "okay";
-
-	ethphy9: ethernet-phy@9 {
-		reg = <9>;
-	};
-};
-
-&nand {
-	status = "okay";
-	chip-delay = <40>;
-
-	partition@0 {
-		label = "uboot";
-		reg = <0x0000000 0x200000>;
-	};
-
-	partition@200000 {
-		label = "certificate";
-		reg = <0x0200000 0x100000>;
-	};
-
-	partition@300000 {
-		label = "preset_cfg";
-		reg = <0x0300000 0x100000>;
-	};
-
-	partition@400000 {
-		label = "dev_params";
-		reg = <0x0400000 0x100000>;
-	};
-	partition@500000 {
-		label = "active_bank";
-		reg = <0x0500000 0x0100000>;
-	};
-
-	partition@600000 {
-		label = "magic";
-		reg = <0x0600000 0x0100000>;
-	};
-
-	partition@700000 {
-		label = "bank1";
-		reg = <0x0700000 0x2800000>;
-	};
-
-	partition@2f00000 {
-		label = "bank2";
-		reg = <0x2f00000 0x2800000>;
-	};
-
-	/* 0x5700000-0x5a00000 undefined in vendor firmware */
-
-	partition@5a00000 {
-		label = "reserved";
-		reg = <0x5a00000 0x2000000>;
-	};
-
-	partition@7a00000 {
-		label = "ubi";
-		reg = <0x7a00000 0x8600000>;
-	};
-};
-
-&pciec {
-	status = "okay";
-};
-
-&pcie0 {
-	status = "okay";
-};
-
-&pinctrl {
-	/* buzzer gpios are connected to two pins of buzzer
-	 * leave it as is due lack of proper driver
-	 */
-	pmx_buzzer: pmx-buzzer {
-		marvell,pins = "mpp12", "mpp13";
-		marvell,function = "gpio";
-	};
-
-	pmx_leds: pmx-leds {
-		marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38",
-			       "mpp39", "mpp40", "mpp42", "mpp43", "mpp44",
-			       "mpp45", "mpp46", "mpp47";
-		marvell,function = "gpio";
-	};
-
-	pmx_buttons: pmx-buttons {
-		marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49";
-		marvell,function = "gpio";
-	};
-
-	pmx_poweroff: pmx-poweroff {
-		marvell,pins = "mpp34";
-		marvell,function = "gpio";
-	};
-};
-
-&rtc {
-	status = "disabled";
-};
-
-&sata {
-	status = "okay";
-	nr-ports = <2>;
-};
-
-&uart0 {
-	status = "okay";
-};
-
-&usb0 {
-	#address-cells = <1>;
-	#size-cells = <0>;
-	status = "okay";
-
-	port@1 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <1>;
-		#trigger-source-cells = <0>;
-
-		hub_port1: port@1 {
-			reg = <1>;
-			#trigger-source-cells = <0>;
-		};
-
-		hub_port2: port@2 {
-			reg = <2>;
-			#trigger-source-cells = <0>;
-		};
-	};
-};
diff --git a/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-nsa310s.dts b/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-nsa310s.dts
deleted file mode 100644
index a72276ed72..0000000000
--- a/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-nsa310s.dts
+++ /dev/null
@@ -1,271 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/dts-v1/;
-
-#include "kirkwood.dtsi"
-#include "kirkwood-6281.dtsi"
-
-/ {
-	model = "ZyXEL NSA310S";
-	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
-
-	aliases {
-		led-boot = &led_green_sys;
-		led-failsafe = &led_red_sys;
-		led-running = &led_green_sys;
-		led-upgrade = &led_red_sys;
-	};
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x10000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8 earlyprintk";
-		stdout-path = &uart0;
-	};
-
-	ocp@f1000000 {
-		pinctrl: pin-controller@10000 {
-			pinctrl-names = "default";
-
-			pmx_usb_power: pmx-usb-power {
-				marvell,pins = "mpp21";
-				marvell,function = "gpio";
-			};
-
-			pmx_pwr_off: pmx-pwr-off {
-				marvell,pins = "mpp27";
-				marvell,function = "gpio";
-			};
-
-			pmx_btn_reset: pmx-btn-reset {
-				marvell,pins = "mpp24";
-				marvell,function = "gpio";
-			};
-
-			pmx_btn_copy: pmx-btn-copy {
-				marvell,pins = "mpp25";
-				marvell,function = "gpio";
-			};
-
-			pmx_btn_power: pmx-btn-power {
-				marvell,pins = "mpp26";
-				marvell,function = "gpio";
-			};
-
-			pmx_led_usb_green: pmx-led-usb-green {
-				marvell,pins = "mpp15";
-				marvell,function = "gpio";
-			};
-
-			pmx_led_copy_green: pmx-led-copy-green {
-				marvell,pins = "mpp22";
-				marvell,function = "gpio";
-			};
-
-			pmx_led_copy_red: pmx-led-copy-red {
-				marvell,pins = "mpp23";
-				marvell,function = "gpio";
-			};
-
-			pmx_led_sys_green: pmx-led-sys-green {
-				marvell,pins = "mpp28";
-				marvell,function = "gpio";
-			};
-
-			pmx_led_sys_red: pmx-led-sys-red {
-				marvell,pins = "mpp29";
-				marvell,function = "gpio";
-			};
-
-			pmx_led_hdd1_green: pmx-led-hdd1-green {
-				marvell,pins = "mpp16";
-				marvell,function = "gpio";
-			};
-
-			pmx_led_hdd1_red: pmx-led-hdd1-red {
-				marvell,pins = "mpp13";
-				marvell,function = "gpio";
-			};
-
-			pmx_pwr_sata1: pmx-pwr-sata1 {
-				marvell,pins = "mpp33";
-				marvell,function = "gpio";
-			};
-
-		};
-
-		i2c@11000 {
-			status = "okay";
-
-			rtc@68 {
-				compatible = "htk,ht1382";
-				reg = <0x68>;
-			};
-		};
-
-		serial@12000 {
-			status = "okay";
-		};
-	};
-
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&pmx_usb_power &pmx_pwr_sata1>;
-		pinctrl-names = "default";
-
-		usb0_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
-		};
-
-		sata1_power: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "SATA1 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&pmx_btn_reset &pmx_btn_copy &pmx_btn_power>;
-		pinctrl-names = "default";
-
-		power {
-			label = "Power Button";
-			linux,code = <KEY_POWER>;
-			gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
-		};
-
-		copy {
-			label = "Copy Button";
-			linux,code = <KEY_COPY>;
-			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
-		};
-
-		reset {
-			label = "Reset Button";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		led_green_sys: green-sys {
-			label = "nsa310s:green:sys";
-			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "default-on";
-		};
-
-		led_red_sys: red-sys {
-			label = "nsa310s:red:sys";
-			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
-		};
-
-		green-hdd1 {
-			label = "nsa310s:green:hdd1";
-			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "ata1";
-		};
-
-		red-hdd1 {
-			label = "nsa310s:red:hdd1";
-			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
-		};
-
-		green-usb {
-			label = "nsa310s:green:usb";
-			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "usb-host";
-		};
-
-		green-copy {
-			label = "nsa310s:green:copy";
-			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
-		};
-
-		red-copy {
-			label = "nsa310s:red:copy";
-			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	gpio_poweroff {
-		compatible = "gpio-poweroff";
-		pinctrl-0 = <&pmx_pwr_off>;
-		pinctrl-names = "default";
-		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
-	};
-};
-
-
-&eth0 {
-	status = "okay";
-
-	ethernet0-port@0 {
-		phy-handle = <&ethphy0>;
-	};
-};
-
-&mdio {
-	status = "okay";
-
-	ethphy0: ethernet-phy@1 {
-		reg = <1>;
-		phy-mode = "rgmii-id";
-		marvell,reg-init = <0x1 0x16 0x0 0x3>,
-				   <0x1 0x10 0x0 0x1017>,
-				   <0x1 0x11 0x0 0x4408>,
-				   <0x1 0x16 0x0 0x0>;
-	};
-};
-
-&nand {
-	status = "okay";
-	chip-delay = <35>;
-
-	partition@0 {
-		label = "uboot";
-		reg = <0x0000000 0x00c0000>;
-		read-only;
-	};
-	partition@c0000 {
-		label = "uboot_env";
-		reg = <0x00c0000 0x0080000>;
-	};
-	partition@140000 {
-		label = "ubi";
-		reg = <0x0140000 0x7ec0000>;
-	};
-};
-
-&pciec {
-	status = "okay";
-};
-
-&pcie0 {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-	nr-ports = <1>;
-};
diff --git a/target/linux/kirkwood/patches-5.15/001-5.18-Add-Ctera-C-200-V1-board.patch b/target/linux/kirkwood/patches-5.15/001-5.18-Add-Ctera-C-200-V1-board.patch
new file mode 100644
index 0000000000..453915e8cf
--- /dev/null
+++ b/target/linux/kirkwood/patches-5.15/001-5.18-Add-Ctera-C-200-V1-board.patch
@@ -0,0 +1,350 @@
+From 5fc74dbdf8f640a7ca7fb92345ac6fbeaa078d65 Mon Sep 17 00:00:00 2001
+From: Pawel Dembicki <paweldembicki@gmail.com>
+Date: Tue, 15 Feb 2022 17:39:22 +0100
+Subject: [PATCH] ARM: dts: kirkwood: Add Ctera C-200 V1 board
+
+Ctera C200 V1 is kirkwood-based 2-Bay NAS.
+
+Hardware:
+  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
+  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
+  - NAND Flash: 256MB (Samsung 216 K9F2G08U0C)
+  - Lan: 1x GBE (Marvell 88E1116R-NNC1)
+  - Storage: 2x SATA HDD 3.5" Slot
+  - USB: 2x USB 2.0 port
+  - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND)
+  - LEDs: 13x GPIO controlled
+  - Buttons: 2x GPIO controlled
+
+Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
+---
+ arch/arm/boot/dts/Makefile             |   1 +
+ arch/arm/boot/dts/kirkwood-c200-v1.dts | 310 +++++++++++++++++++++++++
+ 2 files changed, 311 insertions(+)
+ create mode 100644 arch/arm/boot/dts/kirkwood-c200-v1.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -267,6 +267,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \
+ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ 	kirkwood-b3.dtb \
+ 	kirkwood-blackarmor-nas220.dtb \
++	kirkwood-c200-v1.dtb \
+ 	kirkwood-cloudbox.dtb \
+ 	kirkwood-d2net.dtb \
+ 	kirkwood-db-88f6281.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts
+@@ -0,0 +1,310 @@
++// SPDX-License-Identifier: GPL-2.0-or-later
++/*
++ * Ctera C200 V1 Board Description
++ * Copyright 2021-2022 Pawel Dembicki <paweldembicki@gmail.com>
++ */
++
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++#include <dt-bindings/leds/common.h>
++
++/ {
++	model = "Ctera C200 V1";
++	compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++	chosen {
++		bootargs = "console=ttyS0,115200";
++		stdout-path = &uart0;
++	};
++
++	memory@0 {
++		device_type = "memory";
++		reg = <0x00000000 0x20000000>;
++	};
++
++	keys {
++		compatible = "gpio-keys";
++		pinctrl-0 = <&pmx_buttons>;
++		pinctrl-names = "default";
++
++		power {
++			label = "Power Button";
++			linux,code = <KEY_POWER>;
++			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
++		};
++
++		reset {
++			label = "Reset Button";
++			linux,code = <KEY_RESTART>;
++			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
++		};
++
++		usb1 {
++			label = "USB1 Button";
++			linux,code = <BTN_0>;
++			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
++		};
++
++		usb2 {
++			label = "USB2 Button";
++			linux,code = <BTN_1>;
++			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
++		};
++	};
++
++	gpio-poweroff {
++		compatible = "gpio-poweroff";
++		pinctrl-0 = <&pmx_poweroff>;
++		pinctrl-names = "default";
++		gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
++	};
++
++	leds {
++		compatible = "gpio-leds";
++		pinctrl-0 = <&pmx_leds>;
++		pinctrl-names = "default";
++
++		led-0 {
++			function = LED_FUNCTION_DISK;
++			function-enumerator = <2>;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
++		};
++
++		led-1 {
++			function = LED_FUNCTION_DISK;
++			function-enumerator = <1>;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
++		};
++
++		led-2 {
++			function = LED_FUNCTION_DISK;
++			function-enumerator = <2>;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
++		};
++
++		led-3 {
++			function = LED_FUNCTION_DISK;
++			function-enumerator = <1>;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
++		};
++
++		led-4 {
++			function = LED_FUNCTION_STATUS;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
++		};
++
++		led-5 {
++			function = LED_FUNCTION_STATUS;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
++		};
++
++		led-6 {
++			function = LED_FUNCTION_INDICATOR;
++			color = <LED_COLOR_ID_BLUE>;
++			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
++		};
++
++		led-7 {
++			function = LED_FUNCTION_DISK_ERR;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
++		};
++
++		led-8 {
++			function = LED_FUNCTION_DISK_ERR;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
++		};
++
++		led-9 {
++			function = LED_FUNCTION_USB;
++			function-enumerator = <1>;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
++		};
++
++		led-10 {
++			function = LED_FUNCTION_USB;
++			function-enumerator = <1>;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "usbport";
++			trigger-sources = <&hub_port2>;
++		};
++
++		led-11 {
++			function = LED_FUNCTION_USB;
++			function-enumerator = <2>;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
++		};
++
++		led-12 {
++			function = LED_FUNCTION_USB;
++			function-enumerator = <2>;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "usbport";
++			trigger-sources = <&hub_port1>;
++		};
++	};
++};
++
++&eth0 {
++	status = "okay";
++};
++
++&eth0port {
++	phy-handle = <&ethphy9>;
++};
++
++&i2c0 {
++	status = "okay";
++
++	rtc@30 {
++		compatible = "s35390a";
++		reg = <0x30>;
++	};
++
++	lm63@4c {
++		compatible = "national,lm63";
++		reg = <0x4c>;
++	};
++};
++
++&mdio {
++	status = "okay";
++
++	ethphy9: ethernet-phy@9 {
++		reg = <9>;
++	};
++};
++
++&nand {
++	status = "okay";
++	chip-delay = <40>;
++
++	partition@0 {
++		label = "uboot";
++		reg = <0x0000000 0x200000>;
++	};
++
++	partition@200000 {
++		label = "certificate";
++		reg = <0x0200000 0x100000>;
++	};
++
++	partition@300000 {
++		label = "preset_cfg";
++		reg = <0x0300000 0x100000>;
++	};
++
++	partition@400000 {
++		label = "dev_params";
++		reg = <0x0400000 0x100000>;
++	};
++
++	partition@500000 {
++		label = "active_bank";
++		reg = <0x0500000 0x0100000>;
++	};
++
++	partition@600000 {
++		label = "magic";
++		reg = <0x0600000 0x0100000>;
++	};
++
++	partition@700000 {
++		label = "bank1";
++		reg = <0x0700000 0x2800000>;
++	};
++
++	partition@2f00000 {
++		label = "bank2";
++		reg = <0x2f00000 0x2800000>;
++	};
++
++	/* 0x5700000-0x5a00000 undefined in vendor firmware */
++
++	partition@5a00000 {
++		label = "reserved";
++		reg = <0x5a00000 0x2000000>;
++	};
++
++	partition@7a00000 {
++		label = "rootfs";
++		reg = <0x7a00000 0x8600000>;
++	};
++};
++
++&pinctrl {
++	/* Buzzer gpios are connected to two pins of buzzer.
++	 * This buzzer require a modulated signal from gpio.
++	 * Leave it as is due lack of proper driver.
++	 */
++	pmx_buzzer: pmx-buzzer {
++		marvell,pins = "mpp12", "mpp13";
++		marvell,function = "gpio";
++	};
++
++	pmx_leds: pmx-leds {
++		marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38",
++			       "mpp39", "mpp40", "mpp42", "mpp43", "mpp44",
++			       "mpp45", "mpp46", "mpp47";
++		marvell,function = "gpio";
++	};
++
++	pmx_buttons: pmx-buttons {
++		marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49";
++		marvell,function = "gpio";
++	};
++
++	pmx_poweroff: pmx-poweroff {
++		marvell,pins = "mpp34";
++		marvell,function = "gpio";
++	};
++};
++
++&rtc {
++	status = "disabled";
++};
++
++&sata {
++	status = "okay";
++	nr-ports = <2>;
++};
++
++&uart0 {
++	status = "okay";
++};
++
++&usb0 {
++	#address-cells = <1>;
++	#size-cells = <0>;
++	status = "okay";
++
++	port@1 {
++		#address-cells = <1>;
++		#size-cells = <0>;
++		reg = <1>;
++		#trigger-source-cells = <0>;
++
++		hub_port1: port@1 {
++			reg = <1>;
++			#trigger-source-cells = <0>;
++		};
++
++		hub_port2: port@2 {
++			reg = <2>;
++			#trigger-source-cells = <0>;
++		};
++	};
++};
diff --git a/target/linux/kirkwood/patches-5.15/002-6.2-ARM-dts-kirkwood-Add-Zyxel-NSA310S-board.patch b/target/linux/kirkwood/patches-5.15/002-6.2-ARM-dts-kirkwood-Add-Zyxel-NSA310S-board.patch
new file mode 100644
index 0000000000..b745ea104f
--- /dev/null
+++ b/target/linux/kirkwood/patches-5.15/002-6.2-ARM-dts-kirkwood-Add-Zyxel-NSA310S-board.patch
@@ -0,0 +1,301 @@
+From e977a103840c57d72b52cbc8c17f87f86ef9aa8d Mon Sep 17 00:00:00 2001
+From: Pawel Dembicki <paweldembicki@gmail.com>
+Date: Sat, 29 Oct 2022 22:57:38 +0200
+Subject: [PATCH] ARM: dts: kirkwood: Add Zyxel NSA310S board
+
+Zyxel NSA310S is a NAS based on Marvell kirkwood SoC.
+
+Specification:
+ - Processor Marvell 88F6702 1 GHz
+ - 256MB RAM
+ - 128MB NAND
+ - 1x GBE LAN port (PHY: Marvell 88E1318)
+ - 2x USB 2.0
+ - 1x SATA
+ - 3x button
+ - 7x leds
+ - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC)
+
+Tested-by: Tony Dinh <mibodhi@gmail.com>
+Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
+Acked-by: Adam Baker <linux@baker-net.org.uk>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
+---
+ arch/arm/boot/dts/Makefile             |   1 +
+ arch/arm/boot/dts/kirkwood-nsa310s.dts | 259 +++++++++++++++++++++++++
+ 2 files changed, 260 insertions(+)
+ create mode 100644 arch/arm/boot/dts/kirkwood-nsa310s.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -320,6 +320,7 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
+ 	kirkwood-ns2mini.dtb \
+ 	kirkwood-nsa310.dtb \
+ 	kirkwood-nsa310a.dtb \
++	kirkwood-nsa310s.dtb \
+ 	kirkwood-nsa320.dtb \
+ 	kirkwood-nsa325.dtb \
+ 	kirkwood-openblocks_a6.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
+@@ -0,0 +1,259 @@
++// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
++/*
++ * ZyXEL NSA310S Board Description
++ * Copyright 2020-2022 Pawel Dembicki <paweldembicki@gmail.com>
++ * Copyright (c) 2015-2021, Tony Dinh <mibodhi@gmail.com>
++ * Copyright (c) 2014, Adam Baker <linux@baker-net.org.uk>
++ * Based upon the board setup file created by Peter Schildmann
++ */
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++#include <dt-bindings/leds/common.h>
++
++/ {
++	model = "ZyXEL NSA310S";
++	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
++
++	memory {
++		device_type = "memory";
++		reg = <0x00000000 0x10000000>;
++	};
++
++	chosen {
++		bootargs = "console=ttyS0,115200n8 earlyprintk";
++		stdout-path = &uart0;
++	};
++
++	gpio_poweroff {
++		compatible = "gpio-poweroff";
++		pinctrl-0 = <&pmx_pwr_off>;
++		pinctrl-names = "default";
++		gpios = <&gpio0 27 GPIO_ACTIVE_HIGH>;
++	};
++
++	keys {
++		compatible = "gpio-keys";
++		#address-cells = <1>;
++		#size-cells = <0>;
++		pinctrl-0 = <&pmx_buttons>;
++		pinctrl-names = "default";
++
++		power {
++			label = "Power Button";
++			linux,code = <KEY_POWER>;
++			gpios = <&gpio0 26 GPIO_ACTIVE_HIGH>;
++		};
++
++		copy {
++			label = "Copy Button";
++			linux,code = <KEY_COPY>;
++			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
++		};
++
++		reset {
++			label = "Reset Button";
++			linux,code = <KEY_RESTART>;
++			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
++		};
++	};
++
++	leds {
++		compatible = "gpio-leds";
++		pinctrl-0 = <&pmx_leds>;
++		pinctrl-names = "default";
++
++		led-1 {
++			function = LED_FUNCTION_DISK_ERR;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
++		};
++
++		led-2 {
++			function = LED_FUNCTION_USB;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "usb-host";
++		};
++
++		led-3 {
++			function = LED_FUNCTION_DISK;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "ata1";
++		};
++
++		led-4 {
++			function = LED_FUNCTION_INDICATOR;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
++		};
++
++		led-5 {
++			function = LED_FUNCTION_INDICATOR;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
++		};
++
++		led-6 {
++			function = LED_FUNCTION_STATUS;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "default-on";
++		};
++
++		led-7 {
++			function = LED_FUNCTION_STATUS;
++			color = <LED_COLOR_ID_RED>;
++			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
++		};
++	};
++
++	usb0_power: regulator@1 {
++		compatible = "regulator-fixed";
++		regulator-name = "USB Power";
++
++		regulator-min-microvolt = <5000000>;
++		regulator-max-microvolt = <5000000>;
++		regulator-always-on;
++		regulator-boot-on;
++		gpio = <&gpio0 21 GPIO_ACTIVE_HIGH>;
++	};
++
++	sata1_power: regulator@2 {
++		compatible = "regulator-fixed";
++		regulator-name = "SATA1 Power";
++
++		regulator-min-microvolt = <5000000>;
++		regulator-max-microvolt = <5000000>;
++		regulator-always-on;
++		regulator-boot-on;
++		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
++	};
++
++	thermal-zones {
++		disk-thermal {
++			polling-delay = <20000>;
++			polling-delay-passive = <2000>;
++
++			thermal-sensors = <&hdd_temp>;
++
++			trips {
++				disk_alert: disk-alert {
++					temperature = <40000>;
++					hysteresis = <5000>;
++					type = "active";
++				};
++				disk_crit: disk-crit {
++					temperature = <60000>;
++					hysteresis = <2000>;
++					type = "critical";
++				};
++			};
++		};
++	};
++};
++
++
++&eth0 {
++	status = "okay";
++
++	ethernet0-port@0 {
++		phy-handle = <&ethphy0>;
++	};
++};
++
++&i2c0 {
++	status = "okay";
++
++	rtc@68 {
++		compatible = "htk,ht1382";
++		reg = <0x68>;
++	};
++};
++
++&mdio {
++	status = "okay";
++
++	ethphy0: ethernet-phy@1 {
++		reg = <1>;
++		phy-mode = "rgmii-id";
++		marvell,reg-init = <0x1 0x16 0x0 0x3>,
++				   <0x1 0x10 0x0 0x1017>,
++				   <0x1 0x11 0x0 0x4408>,
++				   <0x1 0x16 0x0 0x0>;
++	};
++};
++
++&nand {
++	status = "okay";
++	chip-delay = <35>;
++
++	partition@0 {
++		label = "uboot";
++		reg = <0x0000000 0x00c0000>;
++		read-only;
++	};
++	partition@c0000 {
++		label = "uboot_env";
++		reg = <0x00c0000 0x0080000>;
++	};
++	partition@140000 {
++		label = "ubi";
++		reg = <0x0140000 0x7ec0000>;
++	};
++};
++
++&pciec {
++	status = "okay";
++};
++
++&pcie0 {
++	status = "okay";
++};
++
++&pinctrl {
++	pinctrl-names = "default";
++
++	pmx_buttons: pmx-buttons {
++		marvell,pins = "mpp24", "mpp25", "mpp26";
++		marvell,function = "gpio";
++	};
++
++	pmx_leds: pmx-leds {
++		marvell,pins = "mpp13", "mpp15", "mpp16", "mpp22", "mpp23",
++						"mpp28", "mpp29";
++		marvell,function = "gpio";
++	};
++
++	pmx_power: pmx-power {
++		marvell,pins = "mpp21", "mpp33";
++		marvell,function = "gpio";
++	};
++
++	pmx_pwr_off: pmx-pwr-off {
++		marvell,pins = "mpp27";
++		marvell,function = "gpio";
++	};
++};
++
++&rtc {
++	status = "disabled";
++};
++
++&sata {
++	status = "okay";
++	nr-ports = <1>;
++	#address-cells = <1>;
++	#size-cells = <0>;
++
++	hdd_temp: sata-port@0 {
++		reg = <0>;
++		#thermal-sensor-cells = <0>;
++	};
++};
++
++&uart0 {
++	status = "okay";
++};
diff --git a/target/linux/kirkwood/patches-5.15/003-6.5-ARM-dts-kirkwood-Add-Endian-4i-Edge-200-board.patch b/target/linux/kirkwood/patches-5.15/003-6.5-ARM-dts-kirkwood-Add-Endian-4i-Edge-200-board.patch
new file mode 100644
index 0000000000..4b0f46bb6d
--- /dev/null
+++ b/target/linux/kirkwood/patches-5.15/003-6.5-ARM-dts-kirkwood-Add-Endian-4i-Edge-200-board.patch
@@ -0,0 +1,249 @@
+From 5668d088ee4ea05db9daaae0645d1d1f579b20f9 Mon Sep 17 00:00:00 2001
+From: Pawel Dembicki <paweldembicki@gmail.com>
+Date: Mon, 3 Oct 2022 09:34:43 +0200
+Subject: ARM: dts: kirkwood: Add Endian 4i Edge 200 board
+
+Add Endian 4i Edge 200 is 5-port firewall.
+It have also clone: Endian UTM Mini (The same hardware, with added WLAN
+card).
+
+Hardware:
+  - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz
+  - Ram: 512MB (4x Nanya NT5TU128M8GE-AC)
+  - NAND Flash: 512MB (Micron 29F4G08AAC)
+  - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2)
+  - Lan 5: 1x GBE (Marvell 88E1116R-NNC1)
+  - Storage: MicroSD Slot
+  - MCPIE: MiniPCIe Slot present [fitted with SparkLan WPEA-110N/E
+          (Atheros AR9280 chipset) in Endian UTM Mini WLAN only]
+  - USB: 1x USB 2.0 port
+  - Console: RJ-45 port
+  - LEDs: 3x GPIO controlled
+
+Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
+Reviewed-by: Andrew Lunn <andrew@lunn.ch>
+Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
+---
+ arch/arm/boot/dts/Makefile                 |   1 +
+ arch/arm/boot/dts/kirkwood-4i-edge-200.dts | 205 +++++++++++++++++++++++++++++
+ 2 files changed, 206 insertions(+)
+ create mode 100644 arch/arm/boot/dts/kirkwood-4i-edge-200.dts
+
+--- a/arch/arm/boot/dts/Makefile
++++ b/arch/arm/boot/dts/Makefile
+@@ -265,6 +265,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \
+ 	keystone-k2g-evm.dtb \
+ 	keystone-k2g-ice.dtb
+ dtb-$(CONFIG_MACH_KIRKWOOD) += \
++	kirkwood-4i-edge-200.dtb \
+ 	kirkwood-b3.dtb \
+ 	kirkwood-blackarmor-nas220.dtb \
+ 	kirkwood-c200-v1.dtb \
+--- /dev/null
++++ b/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
+@@ -0,0 +1,205 @@
++// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
++/*
++ * Endian 4i Edge 200 Board Description
++ * Note: Endian UTM Mini is hardware clone of Endian Edge 200
++ * Copyright 2021-2022 Pawel Dembicki <paweldembicki@gmail.com>
++ */
++
++/dts-v1/;
++
++#include "kirkwood.dtsi"
++#include "kirkwood-6281.dtsi"
++#include <dt-bindings/leds/common.h>
++
++/ {
++	model = "Endian 4i Edge 200";
++	compatible = "endian,4i-edge-200", "marvell,kirkwood-88f6281", "marvell,kirkwood";
++
++	memory {
++		device_type = "memory";
++		reg = <0x00000000 0x20000000>;
++	};
++
++	chosen {
++		bootargs = "console=ttyS0,115200n8";
++		stdout-path = &uart0;
++	};
++
++	leds {
++		compatible = "gpio-leds";
++		pinctrl-0 = <&pmx_led>;
++		pinctrl-names = "default";
++
++		led-1 {
++			function = LED_FUNCTION_SD;
++			color = <LED_COLOR_ID_AMBER>;
++			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
++			linux,default-trigger = "mmc0";
++		};
++
++		led-2 {
++			function = LED_FUNCTION_STATUS;
++			color = <LED_COLOR_ID_AMBER>;
++			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
++		};
++
++		led-3 {
++			function = LED_FUNCTION_STATUS;
++			color = <LED_COLOR_ID_GREEN>;
++			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
++		};
++	};
++};
++
++&eth0 {
++	status = "okay";
++};
++
++&eth0port {
++	speed = <1000>;
++	duplex = <1>;
++};
++
++&eth1 {
++	status = "okay";
++};
++
++&eth1port {
++	phy-handle = <&ethphyb>;
++};
++
++&mdio {
++	status = "okay";
++
++	ethphyb: ethernet-phy@b {
++		reg = <0x0b>;
++
++		marvell,reg-init =
++			/* link-activity, bi-color mode 4 */
++			<3 0x10 0xfff0 0xf>; /* Reg 3,16 <- 0xzzzf */
++	};
++
++	switch0: switch@11 {
++		compatible = "marvell,mv88e6085";
++		reg = <0x11>;
++
++		ports {
++			#address-cells = <1>;
++			#size-cells = <0>;
++
++			port@0 {
++				reg = <0>;
++				label = "port1";
++			};
++
++			port@1 {
++				reg = <1>;
++				label = "port2";
++			};
++
++			port@2 {
++				reg = <2>;
++				label = "port3";
++			};
++
++			port@3 {
++				reg = <3>;
++				label = "port4";
++			};
++
++			port@5 {
++				reg = <5>;
++				phy-mode = "rgmii-id";
++				ethernet = <&eth0port>;
++
++				fixed-link {
++					speed = <1000>;
++					full-duplex;
++				};
++			};
++		};
++	};
++};
++
++&nand {
++	status = "okay";
++	pinctrl-0 = <&pmx_nand>;
++	pinctrl-names = "default";
++
++	partition@0 {
++		label = "u-boot";
++		reg = <0x00000000 0x000a0000>;
++		read-only;
++	};
++
++	partition@a0000 {
++		label = "u-boot-env";
++		reg = <0x000a0000 0x00060000>;
++		read-only;
++	};
++
++	partition@100000 {
++		label = "kernel";
++		reg = <0x00100000 0x00400000>;
++	};
++
++	partition@500000 {
++		label = "ubi";
++		reg = <0x00500000 0x1fb00000>;
++	};
++};
++
++&pciec {
++	status = "okay";
++};
++
++&pcie0 {
++	status = "okay";
++};
++
++&pinctrl {
++	pinctrl-0 = <&pmx_sysrst>;
++	pinctrl-names = "default";
++
++	pmx_sysrst: pmx-sysrst {
++		marvell,pins = "mpp6";
++		marvell,function = "sysrst";
++	};
++
++	pmx_sdio_cd: pmx-sdio-cd {
++		marvell,pins = "mpp28";
++		marvell,function = "gpio";
++	};
++
++	pmx_led: pmx-led {
++		marvell,pins = "mpp34", "mpp35", "mpp49";
++		marvell,function = "gpio";
++	};
++};
++
++&rtc {
++	status = "okay";
++};
++
++&sata_phy0 {
++	status = "disabled";
++};
++
++&sata_phy1 {
++	status = "disabled";
++};
++
++&sdio {
++	pinctrl-0 = <&pmx_sdio_cd>;
++	pinctrl-names = "default";
++	status = "okay";
++	cd-gpios = <&gpio0 28 9>;
++};
++
++&uart0 {
++	status = "okay";
++};
++
++&usb0 {
++	status = "okay";
++};
diff --git a/target/linux/kirkwood/patches-5.15/114-ctera-c-200-v1.patch b/target/linux/kirkwood/patches-5.15/114-ctera-c-200-v1.patch
new file mode 100644
index 0000000000..23922b8d88
--- /dev/null
+++ b/target/linux/kirkwood/patches-5.15/114-ctera-c-200-v1.patch
@@ -0,0 +1,51 @@
+--- a/arch/arm/boot/dts/kirkwood-c200-v1.dts
++++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts
+@@ -14,6 +14,14 @@
+ 	model = "Ctera C200 V1";
+ 	compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+ 
++
++	aliases {
++		led-boot = &led_status_green;
++		led-failsafe = &led_status_red;
++		led-running = &led_status_green;
++		led-upgrade = &led_status_red;
++	};
++
+ 	chosen {
+ 		bootargs = "console=ttyS0,115200";
+ 		stdout-path = &uart0;
+@@ -78,6 +86,7 @@
+ 			function-enumerator = <1>;
+ 			color = <LED_COLOR_ID_GREEN>;
+ 			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "ata1";
+ 		};
+ 
+ 		led-2 {
+@@ -85,6 +94,7 @@
+ 			function-enumerator = <2>;
+ 			color = <LED_COLOR_ID_GREEN>;
+ 			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
++			linux,default-trigger = "ata2";
+ 		};
+ 
+ 		led-3 {
+@@ -94,13 +104,15 @@
+ 			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+ 		};
+ 
+-		led-4 {
++		led_status_red: led-4 {
++			label = "red:status";
+ 			function = LED_FUNCTION_STATUS;
+ 			color = <LED_COLOR_ID_RED>;
+ 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ 		};
+ 
+-		led-5 {
++		led_status_green: led-5 {
++			label = "green:status";
+ 			function = LED_FUNCTION_STATUS;
+ 			color = <LED_COLOR_ID_GREEN>;
+ 			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
diff --git a/target/linux/kirkwood/patches-5.15/115-nsa310s.patch b/target/linux/kirkwood/patches-5.15/115-nsa310s.patch
new file mode 100644
index 0000000000..4c6e08f49c
--- /dev/null
+++ b/target/linux/kirkwood/patches-5.15/115-nsa310s.patch
@@ -0,0 +1,35 @@
+--- a/arch/arm/boot/dts/kirkwood-nsa310s.dts
++++ b/arch/arm/boot/dts/kirkwood-nsa310s.dts
+@@ -16,6 +16,13 @@
+ 	model = "ZyXEL NSA310S";
+ 	compatible = "zyxel,nsa310s", "marvell,kirkwood-88f6702", "marvell,kirkwood";
+ 
++	aliases {
++		led-boot = &led_green_sys;
++		led-failsafe = &led_red_sys;
++		led-running = &led_green_sys;
++		led-upgrade = &led_red_sys;
++	};
++
+ 	memory {
+ 		device_type = "memory";
+ 		reg = <0x00000000 0x10000000>;
+@@ -96,14 +103,16 @@
+ 			gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
+ 		};
+ 
+-		led-6 {
++		led_green_sys: led-6 {
++			label = "nsa310s:green:sys";
+ 			function = LED_FUNCTION_STATUS;
+ 			color = <LED_COLOR_ID_GREEN>;
+ 			gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ 			linux,default-trigger = "default-on";
+ 		};
+ 
+-		led-7 {
++		led_red_sys: led-7 {
++			label = "nsa310s:red:sys";
+ 			function = LED_FUNCTION_STATUS;
+ 			color = <LED_COLOR_ID_RED>;
+ 			gpios = <&gpio0 29 GPIO_ACTIVE_HIGH>;
diff --git a/target/linux/kirkwood/patches-5.15/116-4i-edge-200.patch b/target/linux/kirkwood/patches-5.15/116-4i-edge-200.patch
new file mode 100644
index 0000000000..ffc46c29dc
--- /dev/null
+++ b/target/linux/kirkwood/patches-5.15/116-4i-edge-200.patch
@@ -0,0 +1,34 @@
+--- a/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
++++ b/arch/arm/boot/dts/kirkwood-4i-edge-200.dts
+@@ -20,6 +20,13 @@
+ 		reg = <0x00000000 0x20000000>;
+ 	};
+ 
++	aliases {
++		led-boot = &led_status_green;
++		led-failsafe = &led_status_orange;
++		led-running = &led_status_green;
++		led-upgrade = &led_status_orange;
++	};
++
+ 	chosen {
+ 		bootargs = "console=ttyS0,115200n8";
+ 		stdout-path = &uart0;
+@@ -37,13 +44,15 @@
+ 			linux,default-trigger = "mmc0";
+ 		};
+ 
+-		led-2 {
++		led_status_orange: led-2 {
++			label = "orange:status";
+ 			function = LED_FUNCTION_STATUS;
+ 			color = <LED_COLOR_ID_AMBER>;
+ 			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+ 		};
+ 
+-		led-3 {
++		led_status_green: led-3 {
++			label = "green:status";
+ 			function = LED_FUNCTION_STATUS;
+ 			color = <LED_COLOR_ID_GREEN>;
+ 			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;