aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/brcm47xx
Commit message (Collapse)AuthorAgeFilesLines
* kernel: update linux 3.8 to 3.8.13Gabor Juhos2013-05-261-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36724 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: move CONFIG_MIPS_SEAD3 to genericJonas Gorski2013-05-121-1/+0
| | | | | | Signed-off-by: Jonas Gorski <jogo@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36617 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.8 to 3.8.12Gabor Juhos2013-05-081-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36576 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.8 to 3.8.11Gabor Juhos2013-05-011-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36507 3c298f89-4303-0410-b956-a3cf2f4a3e73
* broadcom-diag: support for the WNDR3700v3Hauke Mehrtens2013-04-281-0/+1
| | | | | | | | | | | | | | | I recently picked up a WNDR3700 to put OpenWRT on, and only after tearing into the box did I find it was one of the v3 boards, with poor OpenWRT support. This patch should add the board detection and LED/button control to the broadcom-diag module, and should generate a netgear .chk image that the bootloader and stock firmware will accept. The changes to the broadcom-diag module are more than a few lines because the WNDR3700v3 is driving its LEDs through an HC164 8-bit shift register. Signed-off-by: Owen Kirby <osk@exegin.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36482 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: use kernel 3.8.10 as default kernelHauke Mehrtens2013-04-281-1/+1
| | | | | | | The biggest change with this kernel is a new partition parser. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36480 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: add board detection for NETGEAR WNDR4500 V2Hauke Mehrtens2013-04-282-8/+12
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36478 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update bcma and ssb for kernel 3.8+ to version from wireless-testing ↵Hauke Mehrtens2013-04-288-115/+7
| | | | | | master-2013-04-26. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36473 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.8 to 3.8.9Gabor Juhos2013-04-265-31/+31
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36453 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: backport SSB/BCMA changes in preparation for a compat-wireless updateFelix Fietkau2013-04-195-15/+15
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36367 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: use old partition names again for kernel 3.8Hauke Mehrtens2013-04-062-1/+21
| | | | | | | | | This fixes sysupgrade. The partition names are used all over the Internet in various howtos. Thank you russell for spotting this problem. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36235 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: fix error in board detection when nvram is not available.Hauke Mehrtens2013-04-062-4/+8
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36234 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.8 to 3.8.6Gabor Juhos2013-04-061-12/+12
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36215 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: generate images for Linksys E.... modelsHauke Mehrtens2013-03-271-0/+9
| | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36139 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: activate image generation for some Netgear devices which are on ↵Hauke Mehrtens2013-03-271-7/+7
| | | | | | the market and should be supported. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36137 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: generate images for more WRT...N modelsHauke Mehrtens2013-03-271-0/+5
| | | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36136 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: generate images for some more devicesHauke Mehrtens2013-03-201-3/+3
| | | | | | | These devices should be supported by trunk now. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36099 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update linux 3.8 to 3.8.3Gabor Juhos2013-03-152-15/+15
| | | | | | | | Also refresh the related generic/platform patches. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@36039 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: refresh configHauke Mehrtens2013-03-102-6/+0
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35948 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: add some more partition parser fixes by Rafał MiłeckiHauke Mehrtens2013-03-094-14/+156
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35912 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: netconfig: add bacis support for swconfigHauke Mehrtens2013-03-091-25/+27
| | | | | | | Parse the cpu port from swconfig and explicitly mark the cpu port as tagged. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35911 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: bgmac: omit the fcsHauke Mehrtens2013-02-282-0/+38
| | | | | | | This fixes #13058 and hopefully #12927 git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35834 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: bgmac: update to version form netdev git repositoryHauke Mehrtens2013-02-282-26/+134
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35833 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: use bcm47xx_board_get() and detect some more boards in flash ↵Hauke Mehrtens2013-02-251-74/+37
| | | | | | partition driver git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35791 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: board detection WNDR3400v2Hauke Mehrtens2013-02-253-4/+9
| | | | | | | | | | | | | | | | | WNDR3400v2 is based on BCM53xx . Image that is created breaks the router somehow therefore "#". CFE and NVRAM contain different vars - example: CFE line original: Device eth0: hwaddr 74-44-01-37-C6-69, ipaddr 192.168.1.1, mask 255.255.255.0 CFE after openwrt: Device eth0: hwaddr 00-FF-FF-FF-FF-FF, ipaddr 192.168.1.1, mask 255.255.255.0 Logs were posted earlier on this mailing list: https://lists.openwrt.org/pipermail/openwrt-devel/2012-July/016174.html Different logs with factory firmware are in the wiki: http://wiki.openwrt.org/toh/netgear/wndr3400#wndr3400v2 (and on wikidevi for example) Signed off by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35790 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: use same board detection code as kernel 3.8Hauke Mehrtens2013-02-241-24/+24
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35770 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: do not use vlan0 any more.Hauke Mehrtens2013-02-203-43/+43
| | | | | | | | | | The Broadcom switch driver says that vlan0 should not be used with any switch other than bcm5325. This makes OpenWrt always use vlan1 and vlan2 instead. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35704 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: add initial support for kernel 3.8Hauke Mehrtens2013-02-1654-0/+7785
| | | | | | | | | | | | | This contains the following new bigger changes: * new partition parser which still could lake some features or have bugs * new nand flash driver * using physmap-flash flash driver for parallel flash * some changes to the serial flash driver With these changes OpenWrt starts using more of the mainline flash drivers. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35632 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: BGMAC - Adjust AutoLoad number to be prior to switch modulesHauke Mehrtens2013-02-161-1/+1
| | | | | | | | | | | Adjust the "AutoLoad" number for the BGMAC module to be prior to the switch modules. This probably isn't real important as the modules are loaded in the correct order by preinit anyway. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35625 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: improve cpuport detection for filesafeHauke Mehrtens2013-02-161-13/+9
| | | | | | | | | Do not try to load bcm57xx.ko any more this is not needed for kernel 2.6 and 3.X Ask the switch driver where the CPU port is. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35624 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: fix network config on simpleshare Hauke Mehrtens2013-02-161-0/+6
| | | | | | | | | | | The included patch will generate a correct network configuration on the simpletech simpleshare. Thank you for the patch Will Holmes (RealOpty) This closes #12361. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35623 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: handle return values of cfe_env_get() correctly.Hauke Mehrtens2013-02-161-4/+5
| | | | | | | This closes #12746. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35622 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: bgmac: fix unaligned accesses to network headers.Hauke Mehrtens2013-02-161-8/+60
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35621 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: fix unaligned access to mac addressHauke Mehrtens2013-02-161-0/+18
| | | | | | | | | | The mac address should be aligned to u16 to prevent an unaligned access in drivers/ssb/pci.c where it is casted to __be16. This closes #9824. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35618 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: try to automatically detect if the wan port is at port 4 and not ↵Hauke Mehrtens2013-02-161-1/+12
| | | | | | | | | at port 0. This should fix #13000. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35617 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: if the cpuport of the switch is port 8 assume vlan0ports: "1 2 3 4 ↵Hauke Mehrtens2013-02-141-16/+8
| | | | | | 8" and vlan0ports: "0 8" git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35597 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: configure vlan correctly on some recent devices.Hauke Mehrtens2013-02-131-1/+4
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35587 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: add some more fixes to bgmacHauke Mehrtens2013-02-121-7/+35
| | | | | | | Thank you Rafał Miłecki and Nathan Hintz git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35574 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: update tg3 to the version send upstreamHauke Mehrtens2013-02-121-114/+63
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35573 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: fix name of kmod-ocf-ubsec-ssbHauke Mehrtens2013-02-061-1/+1
| | | | | | | | | This also removes kmod-ocf, because kmod-crypto-ocf is automatically selected by kmod-ocf-ubsec-ssb. Thank you Manuel Munz <freifunk@somakoma.de> for the patch. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35509 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: bgmac: make it possible to set the devices into promisc mode when ↵Hauke Mehrtens2013-02-062-0/+206
| | | | | | | | | it is already up This fixes #12927. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35507 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: fix detection of Asus RT-N16Hauke Mehrtens2013-02-041-3/+4
| | | | | | | This fixes #12936. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35492 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Add Failsafe support for Linksys E3000V1 / WRT610NV2Hauke Mehrtens2013-02-041-0/+1
| | | | | | | | | | | | | | Adds specification of the correct cpu_port for Linksys E3000V1 and WRT610NV2 in /lib/preinit/05_init_interfaces_brcm. The list of devices will need to be expanded. Is there a way to determine the correct cpu_port to use in a generic sense; for instance, if "/proc/switch/eth0/port/8" exists, or if "/sys/class/net/eth0/device/driver/module/drivers/bcma:bgmac" exists? Could a similar method be used in "/etc/init.d/netconfig"? Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35491 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: Fix switch config on 4716/53115 devicesHauke Mehrtens2013-02-041-1/+1
| | | | | | | Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35490 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: load pps_core and ptp before tg3 to make the interface available ↵Hauke Mehrtens2013-01-271-0/+2
| | | | | | for failsafe. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35341 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: create image for Netgear WNDR3400 V1Hauke Mehrtens2013-01-261-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35323 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: add initial board detection codeHauke Mehrtens2013-01-265-6/+366
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35322 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: add gpio to irq function againHauke Mehrtens2013-01-262-0/+116
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35321 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: change generic profilesHauke Mehrtens2013-01-2417-78/+218
| | | | | | | | | The default profile now contains Ethernet drivers for all the types found on supported boards. There are other profiles for each Ethernet driver. git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35314 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: BCMA - Update default IRQ assignment per upstream changeHauke Mehrtens2013-01-121-0/+9
| | | | | | | | | | Update the default IRQ assignment for unrecognized devices per the upstream change. Signed-off-by: Nathan Hintz <nlhintz@hotmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@35121 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-29 11:10:34 +0000