| Commit message (Collapse) | Author | Age | Files | Lines |
... | |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The RB91x boards are suffering from ethernet packet loss after a cold
boot. The cause of the problem is that the AR8035 PHYs requires special
register settings to work reliably on these boards.
Enable the RGMII TX, RX delays and disable SmartEE functionality of
the AR8035 PHYs. Also enable the RXD delay in the ETH_CFG register
to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40509 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With this patch OpenWRT supports the following on the ZyXEL NBG 6716:
-WiFi 2G (ath9k)
-WiFi 5G (ath10k)
-NAND flash
-2 Ethernet interfaces
-USB 2.0
-LEDs including switch
-reasonale defaults at first boot
Signed-off-by: André Valentin <avalentin@marcant.net>
Patchwork: http://patchwork.openwrt.org/patch/5101/
[juhosg:
- rename and refresh kernel patch,
- fix a few typos,
- change button key codes,
- use zyxel prefix in LED names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40499 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Apart from the wireless chip, the WNDR3700 v4 and the WNDR4300
is the same device. Indicate this in the kernel files.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40479 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The 5V power of the USB is controlled by a GPIO pin of
the external WiFi chip. Setup the GPIO bitmasks in the
platform data of the WiFi chip to ensure that the 5V
power gets enabled by the ath9k driver.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40478 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40477 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40475 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
The bootloader does not initializes the output function
correctly for all LEDs. DO that from the board setup code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40474 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
| |
The hardware manual says amber so change the color part of
the LED names to reflect that. Also update the constant names.
Based on the the WNDR3700v4 support patch from Ralph Perlich:
http://patchwork.openwrt.org/patch/4763/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40473 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
| |
Everything seems to be working fine. Potential issues:
* VLAN port IDs are reversed with regard to the numbers on the case.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40400 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
I don't have access to the specs, so I'm not sure about every detail, but I
haven't seen any problems with my test system, a TL-WR841N v9. It looks pretty
much like a QCA955x without PCI, a little twist in the clock calculation and
a AR9331-compatible switch.
Features not yet supported:
* EHCI (my test system doesn't have USB)
* ? (I have no idea if the QCA953x has any other features I don't know about
that aren't used by the TL-WR841N v9)
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40399 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch-by: Lars Bøgild Thomsen <lth@cow.dk>
Patchwork: http://patchwork.openwrt.org/patch/4922/
[juhosg:
- use a separate patch for kernel changes,
- reorder Kconfig and Makefile entries,
- change function and variable names to be lowercase only
and fix misaligned tabs in mach-gs-oolite.c,
... ]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@40032 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
The flash address passed to rb_init_info() is bogus,
use the predefined AR71XX_SPI_BASE macro instead.
Compile tested only.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39891 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
sizeof(array_from_function_definition) gives back the size of the pointer.
sizeof(type) * array_size should be used in memset.
Signed-off-by: David Völgyes <david.volgyes@gmail.com>
Patchwork: http://patchwork.openwrt.org/patch/4950/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39890 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39704 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The RB91x boards are using a serial shift register
connected to the SPI bus to drive some of the LEDs.
Rework the board setup code to register a SPI device
for that. This makes it possible to use the 'spi-74x164'
driver to control the device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39703 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Rewrite tha rb91x-nand driver to use GPIO API to
modify the NAND control lines.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39700 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39699 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When the RB91x device uses a GbE link the connection
suffers from packet loss:
root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 20 -q
PING 192.168.1.254 (192.168.1.254): 65507 data bytes
--- 192.168.1.254 ping statistics ---
20 packets transmitted, 9 packets received, 55% packet loss
round-trip min/avg/max = 4.570/4.815/4.999 ms
Using a different PLL value fixes the issue.
root@OpenWrt:/# ping 192.168.1.254 -s 65507 -c 100 -q
PING 192.168.1.254 (192.168.1.254): 65507 data bytes
--- 192.168.1.254 ping statistics ---
100 packets transmitted, 100 packets received, 0% packet loss
round-trip min/avg/max = 4.449/5.413/13.870 ms
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39642 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
I noticed that the patch at http://patchwork.openwrt.org/patch/4017/
for adding support for the MikroTik RouterBOARD 951Ui-2HnD had been
abandoned because it wasn't generated and sent to the mailing list
correctly and doesn't apply as a result. I have cleaned up this patch.
When testing this on real hardware, I also noticed that wireless didn't
work, so this patch fixes that as well.
This patch applies cleanly to SVN 39392.
Signed-off-by: Matthew Reeve <mreeve@tenxnetworks.com>
Patchwork: http://patchwork.openwrt.org/patch/4773/
[juhosg:
- drop the 'rb951ui_wlan_init' function and rework the code to
use the recently introduced rb95x_wlan_init function instead,
- fix GPIO number of the port5 LED,
- rename LEDs according to the standard LED naming conventions,
and use 'rb' prefix in the names]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39641 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch-by: TenNinjas <tenninjas@tenninjas.ca>
Patchwork: http://patchwork.openwrt.org/patch/4848/
[juhosg:
- rename and refresh kernel patch,
- merge the board setup code into mach-archer-c7.c and drop
mach-tl-wdr49000-v2.c]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39635 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39401 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39400 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39395 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
On recent TL-WDR4300 boards the external LNAs of the 2.4GHz
interface are connected to GPIO lines. Because these GPIO
lines are disabled by default, the RX sensitivity of the
device is quite bad.
Setup the GPIOs of the external LNAs to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39392 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39374 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4743/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39361 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39346 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39345 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39341 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
The eth5 LED on the RB2011 is not working because the
LED control rule is missing. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39335 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39217 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Use the ath79_wmac_set_ext_lna_gpio helper instead
of exporting the GPIOs.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39216 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Tested-by: Steven Haigh <netwiz@crc.id.au>
Patchwork: http://patchwork.openwrt.org/patch/4689/
[juhosg:
- remove the GPIO LED changes, the My Net N600 has no yellow LEDs at all,
- change subject and update the commit message]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39214 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The LNAs need to be enabled by setting their respective GPIO to high even
though the original firmware's setting sets them to low on initialization.
Obviously the LNAs are then later initialized by the driver on the OEM
firmware. Without this fix the device is mostly "deaf".
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4688/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39213 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39161 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
It makes no sense, the SoC has no built-in switch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39160 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The hardware supports large ethernet frames. Override
the maximum frame length and packet lenght mask in the
platform data to allow to use large MTU on the ethernet
interfaces.
Limit the feature to AR934x SoCs for now. It should work
on some other SoCs as well, but those has not been tested
yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39149 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
This will allow to use SoC specific values for both.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39145 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
Now that the switch is working correctly I had the chance to actually
test the LED config.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4616/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39129 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The bootloader on the WD My Net N750 disables the ports on it's internal
AR8327N switch by powering them down. The stock firmware then brings the
ports back up again by starting the auto negotiation process on each
port.
This fix implements just that.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4615/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39128 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
This enables us to add fixups to the board specific code for boards that
require special treatment of PHYs on mdio bus reset.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
http://patchwork.openwrt.org/patch/4614/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39127 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
|
|
| |
This enables us to modify the ag71xx_mdio_platform_data from within the
board support files.
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
Patchwork: http://patchwork.openwrt.org/patch/4613/
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39126 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
It is only on RB911G-5HPnD and RB912UAG-5HPnD boards.
The LEDs and the USB port is not working yet.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39102 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39096 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39095 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39094 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Also remove unused RB_* defines.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39092 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
| |
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39091 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
|
| |
Set up the chipselect GPIO directly in rb95x_nand_init
instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39087 3c298f89-4303-0410-b956-a3cf2f4a3e73
|
|
|
|
|
|
|
|
| |
Signed-off-by: Felix Kaechele <heffer@fedoraproject.org>
[juhosg: use a separate patch for kernel changes]
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
git-svn-id: svn://svn.openwrt.org/openwrt/trunk@39077 3c298f89-4303-0410-b956-a3cf2f4a3e73
|