aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
...
* ar71xx: migrate tplink cpe510 to new build stepsJohn Crispin2016-03-231-48/+26
| | | | | | | | | cpe510: Tested sysupgrade and initramfs. Untested: webIf w/ factory.bin & recovery.bin Signed-off-by: Alexander Couzens <lynxis@fe80.eu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49081 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx/image: allow builds of loader without cmdline injectingJohn Crispin2016-03-231-3/+7
| | | | | | | | | | | | | On most platforms the cmdline is supplied by the loader to the kernel. When using an elf loader with cmdline the size is bloated by 512k. For loader-elf platforms like the cpe510 better use loader-elf but patch the cmdline into the kernel. wdr1043: Tested loader still works using sysupgade image. Signed-off-by: Alexander Couzens <lynxis@fe80.eu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49080 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx/image: introduce LOADER_TYPE to support elf loadersJohn Crispin2016-03-231-3/+4
| | | | | | | | | The loader decompress a lzma compressed kernel. Some bootloaders only support elf files like the tplink cpe510 Signed-off-by: Alexander Couzens <lynxis@fe80.eu> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49079 3c298f89-4303-0410-b956-a3cf2f4a3e73
* uboot-zynq: Update to U-Boot 2016.03 releaseJohn Crispin2016-03-231-2/+2
| | | | | | Signed-off-by: Jason Wu <jason.wu.misc@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49078 3c298f89-4303-0410-b956-a3cf2f4a3e73
* zynq: Simplify boot-img buildJohn Crispin2016-03-231-7/+11
| | | | | | | | | by adding Device/DefaultConfig macro to define the dts and device in lower case. Signed-off-by: Jason Wu <jason.wu.misc@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49077 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: WNR1000v2: enable control of all LEDs and buttonsJohn Crispin2016-03-232-5/+128
| | | | | | | | | This patch provides full GPIO support for WNR1000v2 (LEDs and buttons). It exposes all LEDs to operating system, including Ethernet ones. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49076 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add QCA955X GPIO mux and function definitionsJohn Crispin2016-03-238-76/+176
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49075 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Add support for ath79_gpio_function_* on QCA955XJohn Crispin2016-03-232-5/+21
| | | | | | Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49074 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: build airo on x86 onlyJohn Crispin2016-03-231-1/+1
| | | | | | | | | | | | | airo requires ISA_DMA_API and that symbol is only set on some ppc,malta,x86 x86 is probably only platform where that driver is used fixes buildbot errors on ar71xx,lantiq ...: airo.ko is missing Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49073 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Revert "ar71xx: Clear bits in ath79_setup_qca955x_eth_cfg"John Crispin2016-03-231-13/+3
| | | | | | | | | | | | | Not all mach-* files set all boards correctly in ETH_CFG. They depend on some preset values by u-boot which were not previously modified by ath79_setup_qca955x_eth_cfg. Avoiding to modify them in this function keeps it backward compatible for these boards. This reverts commit 119b8ab2c2eac237ec4e9c4d0ed53df22b5c6978. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49072 3c298f89-4303-0410-b956-a3cf2f4a3e73
* Revert "ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955x"John Crispin2016-03-2317-29/+19
| | | | | | | | | | | | The default delays RXD 3. RDV 3, TXD 0, TXE 0 doesn't seem to work for some boards. These boards depend on the preset values of u-boot which may differ. This reverts commit f2d4bb96b62512caa161dcc2867c91692fb16a38. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49071 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR1750John Crispin2016-03-231-1/+23
| | | | | | | | | | | | The MR1750 must unset some bits in ETH_CFG which were set by u-boot to work correctly under OpenWrt. But the global function ath79_setup_qca955x_eth_cfg will not unset all of them to increase the backward compatiblity with older mach-* files. A private (simplified) version for MR1750 can be used instead. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49070 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Use private version of ath79_setup_qca955x_eth_cfg for MR900John Crispin2016-03-231-1/+23
| | | | | | | | | | | | The MR900 must unset some bits in ETH_CFG which were set by u-boot to work correctly under OpenWrt. But the global function ath79_setup_qca955x_eth_cfg will not unset all of them to increase the backward compatiblity with older mach-* files. A private (simplified) version for MR900 can be used instead. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49069 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: set ubifs parameters for Default profileJohn Crispin2016-03-231-0/+1
| | | | | | | | | | | | | | | | | | Work-around obsolete mkfs/ubifs code. Unlike squashfs, ubifs images should be generated per-device so minimum I/O unit size, logical erase block size, maximum logical erase block count can be defined for the specific flash-chips parameters. Also, generating ubinized images is unrelated to rootfs being ubifs or squashfs, but rather depends on the device supporting UBI or not. In the meantime and in order to fix an error which currently causes the image generation on buildbot to fail, work-around by defining UBIFS_OPTS for the Default profile. See also http://buildbot.openwrt.org:8010/builders/oxnas/builds/246/steps/compile_8/logs/stdio Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49068 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mediatek: patch block2mtd to allow cmdlineparts to workJohn Crispin2016-03-232-1/+34
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49067 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mediatek: update patchesJohn Crispin2016-03-2268-303/+2672
| | | | | | | | fixes trgmii on old eco and adds nand support Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49066 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mt76: fix compile errorJohn Crispin2016-03-211-0/+11
| | | | | | | | gcc complained about uninitialized variables Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49065 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mediatek: bump to v4.4John Crispin2016-03-21132-49267/+22597
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49064 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic/4.4: remove ISSI SI25CD512 SPI flash support patchGabor Juhos2016-03-211-22/+0
| | | | | | | | The flash is already supported in mainline kernel since 4.3-rc1. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49063 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: lzma-loader: fix O32 ABI conformanceGabor Juhos2016-03-211-0/+3
| | | | | | | | | | | | | | | | | | | According to the calling convention of the o32 ABI the caller function must reserve stack space for $a0-$a3 registers in case the callee needs to save its arguments. The assembly startup code does not reserve stack space for these registers thus when the main C function needs to save its arguments, that will cause a stack overflow. Fix the assembly code to reserve stack space for the registers to avoid that. Untested. It seems that the lzma-loader is not used at all? Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49062 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: lzma-loader: fix O32 ABI conformanceGabor Juhos2016-03-211-0/+3
| | | | | | | | | | | | | | | | | | | According to the calling convention of the o32 ABI the caller function must reserve stack space for $a0-$a3 registers in case the callee needs to save its arguments. The assembly startup code does not reserve stack space for these registers thus when the main C function needs to save its arguments, that will cause a stack overflow. Fix the assembly code to reserve stack space for the registers to avoid that. Compile tested only. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49061 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: lzma-loader: fix cache invalidationGabor Juhos2016-03-211-4/+4
| | | | | | | | | | | | | | | The current code only partially invalidates both caches because the cache size and cache-line size values are incorrectly passed to the C code. Fix the assembly code to pass the arguments in the correct order. Compile tested only. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49060 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: lzma-loader: remove trailing whitespaces from head.SGabor Juhos2016-03-211-9/+9
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49059 3c298f89-4303-0410-b956-a3cf2f4a3e73
* adm5120: lzma-loader: fix cache invalidationGabor Juhos2016-03-211-4/+4
| | | | | | | | | | | | | | | The current code only partially invalidates both caches because the cache size and cache-line size values are incorrectly passed to the C code. Fix the assembly code to pass the arguments in the correct order. Compile tested only. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49058 3c298f89-4303-0410-b956-a3cf2f4a3e73
* adm5120: lzma-loader: remove trailing whitespaces from head.SGabor Juhos2016-03-211-1/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49057 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: lzma-loader: fix cache invalidationGabor Juhos2016-03-211-4/+4
| | | | | | | | | | | | | | | The current code only partially invalidates both caches because the cache size and cache-line size values are incorrectly passed to the C code. Fix the assembly code to pass the arguments in the correct order. Tested on RB532. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49056 3c298f89-4303-0410-b956-a3cf2f4a3e73
* generic: lzma-loader: remove trailing whitespaces from start.SGabor Juhos2016-03-211-4/+4
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49055 3c298f89-4303-0410-b956-a3cf2f4a3e73
* odhcp6c : Silence mtu write error warningsJohn Crispin2016-03-201-1/+1
| | | | | | | | | | Silence warning "daemon.notice netifd: wan6 (1139): sh: write error: Invalid argument" when an invalid MTU is received via RA as kernel refuses to accept IPv6 mtu values which are smaller than 1280 and bigger than the device mtu. Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49054 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: WNR1000v2: fix for random WLAN MACJohn Crispin2016-03-201-2/+7
| | | | | | | | | | | Fix for invalid/random WLAN MAC address in WNR1000v2. Permanent platform MAC is calculated and assigned during system startup. WLAN MAC follows wired Ethernet interface addresses. This is the same fix as for WNR2000v3 and WNR612v2. Signed-off-by: Michal Cieslakiewicz <michal.cieslakiewicz@wp.pl> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49051 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: use upstream mechanism to append device tree fileJohn Crispin2016-03-206-69/+91
| | | | | | | | | | | Instead of using our patch-dtb program just place the device tree behind the kernel binary and then let the in kernel mechanism fetch it. This also adds support for having the device tree file in the boot loader. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49050 3c298f89-4303-0410-b956-a3cf2f4a3e73
* wireless: remove rtl8188eu (staging)John Crispin2016-03-201-18/+0
| | | | | | | | | | | | | - depends on CFG80211 (upstream: 9da4aa48d04bbdbae3c959809e14da2bf0c53f61) in os_dep/mon.c This removes rtl8188eu completely from OpenWrt since mac80211/compat-wireless/backports does not provide staging wireless drivers Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49049 3c298f89-4303-0410-b956-a3cf2f4a3e73
* wireless: add vendor dirsJohn Crispin2016-03-201-1/+3
| | | | | | | | Kernel 4.5 changes wireless driver organisation Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49048 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: add cisco airoJohn Crispin2016-03-201-0/+17
| | | | | | | | airo depends on cfg80211, move it to mac80211 Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49047 3c298f89-4303-0410-b956-a3cf2f4a3e73
* wireless: remove cisco airoJohn Crispin2016-03-201-16/+0
| | | | | | | | | it depends on cfg80211 cfg80211 & wext drivers don't mix on OpenWrt Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49046 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: MiWifi-Nano - change gpios to leds, add to default build groupJohn Crispin2016-03-203-23/+21
| | | | | | | | | | | | 1) Use leds to indicate: Red - Power Amber - Radio On Blue - Wifi associated 2) Add profile to default build group for MT7628 subtarget Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49045 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: sync cpu-hotplug with mach-realviewJohn Crispin2016-03-201-4/+3
| | | | | | | | | Make mach-oxnas/hotplug.c look more similar to mach-realview/hotplug.c, just cosmetics and maintainability concerns, no functional changes. Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49044 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: add spinlock in pinctrl driverJohn Crispin2016-03-201-2/+16
| | | | | | | | Try to address a race-condition in pinctrl-oxnas.c Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49043 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: also reset GPIO B registers on bootJohn Crispin2016-03-201-6/+6
| | | | | | | | | | Clear both, SYS_CTRL_*_SEL and SEC_CTRL_*_SEL on boot instead of writing to SYS_CTRL_*_SEL twice which looks like a copy-paste error. Thanks to anonymous to bring this up in #21892! Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49042 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: switch to new image generation templateJohn Crispin2016-03-201-86/+44
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49041 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: add Default profile and reorganize device profilesJohn Crispin2016-03-204-23/+52
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49040 3c298f89-4303-0410-b956-a3cf2f4a3e73
* include/image.mk: allow including U-Boot environment in UBIJohn Crispin2016-03-201-0/+1
| | | | | | Signed-off-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49039 3c298f89-4303-0410-b956-a3cf2f4a3e73
* linux-firmware: fix rt73-usb-firmware packageHauke Mehrtens2016-03-191-2/+2
| | | | | | | | | | | | | | Some parts of this package were named rt73-pci-firmware before which looks like a copy and past error. This renames all parts to rt73-usb- firmware and then the firmware gets build and the dependencies from the package with the kernel module are also working correctly. This fixes #22069 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49037 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update kernel 4.1 to version 4.1.20Hauke Mehrtens2016-03-1832-188/+190
| | | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49035 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: libertas-spi: deactivate for UML targetHauke Mehrtens2016-03-171-1/+1
| | | | | | | | | | The UML target does not have spi support. This fixes a build problem found by the build bot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49034 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: add missing kernel optionsHauke Mehrtens2016-03-172-0/+2
| | | | | | | | | This was found by the build bot. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49033 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update kernel 4.4 to version 4.4.6Hauke Mehrtens2016-03-1711-57/+12
| | | | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49032 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Use PHY fixups for Open Mesh MR1750John Crispin2016-03-161-3/+22
| | | | | | | | | | | | | | | | | | The delays of PHY/MAC on the MR1750 are done by u-boot and OpenWrt in different ways. u-boot only modifies the ETH_CFG of the QCA955x based on the link speed. But OpenWrt can only modify the PHY delays based on the link speed. This can lead to communication problems when u-boot initializes the ETH_CFG for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY delays to an incompatible value. Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and only rely on the AT803x PHY settings. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49031 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Use PHY fixups for Open Mesh MR900John Crispin2016-03-161-3/+22
| | | | | | | | | | | | | | | | | | The delays of PHY/MAC on the MR900 are done by u-boot and OpenWrt in different ways. u-boot only modifies the ETH_CFG of the QCA955x based on the link speed. But OpenWrt can only modify the PHY delays based on the link speed. This can lead to communication problems when u-boot initializes the ETH_CFG for a specific link speed (e.g. 10BASE-T) but then OpenWrt the sets the PHY delays to an incompatible value. Instead reset the ETH_CFG delay bits of the QCA955x to a specific value and only rely on the AT803x PHY settings. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49030 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Allow to set the RXDV, RXD, TXD, TXE delays for QCA955xJohn Crispin2016-03-1619-21/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some u-boot versions for QCA955x change the delays based on the link speed during boot. This usually breaks the support of other linkspeeds when OpenWrt is booted. It also conflicts with the at803x_platform_data::fixup_rgmii_tx_delay. OpenWrt has to set its own values in QCA955X_GMAC_REG_ETH_CFG. The default RGMII values from the Atheros u-boot are currently used to preset the existing mach files. These may have to be adjusted for boards using different values but which are not currently set them explicitely in OpenWrt. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> Cc: Gabor Juhos <juhosg@openwrt.org> Cc: Imre Kaloz <kaloz@openwrt.org> Cc: Christian Beier <cb@shoutrlabs.com> Cc: Chris R Blake <chrisrblake93@gmail.com> Cc: Benjamin Berg <benjamin@sipsolutions.net> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Cc: Matthias Schiffer <mschiffer@universe-factory.net> Cc: Dirk Neukirchen <dirkneukirchen@web.de> Cc: Christian Mehlis <christian@m3hlis.de> Cc: Luka Perkov <luka@openwrt.org> Cc: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49029 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Clear bits in ath79_setup_qca955x_eth_cfgJohn Crispin2016-03-161-3/+13
| | | | | | | | | | | Some u-boot versions for QCA955x set currently not cleared bits depending on the used link speed. This breaks the rx/tx under OpenWrt. The mach-*.c file is responsible to select the correct configuration bits and thus the ath79_setup_qca955x_eth_cfg has to clear the unset. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@49028 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-19 03:22:29 +0000