aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Fix too small rx bufferJohn Crispin2015-10-051-4/+12
| | | | | | | | | | | | | | | | | | The driver assumes that the maximum received buffer for non-jumbo frames is 1536 bytes. But the allocation of the rx fragment doesn't reflect that. It currently allocates fragments which will only be large enough to be used as rx buffer with the size of 1534 bytes. This is problematic because the GMAC will now try to write to 2 bytes which don't belong to its receive buffer when a large enough ethernet frame is received. This may already be a problem on existing chips but will at least become a problem when the 1536 byte rx modus is enabled on MT7621a. It is required on this SoC to receive ethernet frames which use their full 1500 bytes MTU and a VLAN header next to the switch VLAN tag. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47116 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Fix setting of rx buffer lengthJohn Crispin2015-10-052-2/+3
| | | | | | | | | | | | | | The length of the DMA rx buffer was always set to 0 because the function for extracting the length was used to calculate the value for setting it. Instead the macro has to be split in a get and set function similar to the TX_DMA_(GET_|)PLEN(0|1) macro. No problem was noticed on MT7621a before this was changed and thus maybe it was hidden by different problem which is not yet fixed. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47115 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Allow to receive vlan over untag ports on MT7530John Crispin2015-10-051-3/+33
| | | | | | | | | | | | | | | | | | | | The MT7530 switch driver with enable_vlan set will automatically set all ports to the user port mode. The hardware will remove the incoming vlan tag on these ports and use it for its internal vlan. This is usually not wanted and makes it impossible to communicate via vlan over the switch in both directions. It is possible to configure a switch port to "transparent mode" when this port is only used as untag in the switch VLANs. This will disable the VLAN untagging of packets when they were received on this port. The tagging on "tag" ports based on the vlan id is still working. The transparent port mode cannot be used when a port is both used in a VLAN as "tag" and in another one as "untag" port. Signed-off-by: Sven Eckelmann <sven@open-mesh.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47114 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add build files for HiWiFi HC5x61 modelsJohn Crispin2015-10-052-0/+53
| | | | | | | | | | | | | | HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com <http://www.hiwifi.com/>. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them. The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval. v3 fix 1: Spaces -> Tabs 2: Removed some packages Signed-off-by: Xiaoning Kang <kangxn@163.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47113 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add DTS files for HiWiFi HC5x61 modelsJohn Crispin2015-10-054-0/+299
| | | | | | | | | | | | | | HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them. The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval. v3 fix 1: Merged most stuff into dtsi file 2: Remove unnecessary empty lines. Signed-off-by: Xiaoning Kang <kangxn@163.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47112 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ramips: Add base-files for HiWiFi HC5x61 modelsJohn Crispin2015-10-055-10/+45
| | | | | | | | | | | | | | | HiWiFi HC5661/5761/5861 models are manufactured by http://www.hiwifi.com. These models have similar hardware specs(MT7620A + 128M DDR2 + 16M flash). This patch adds support for them. The original author is Justin Liu (rssnsj@gmail.com). I ported the patch to trunk and submitted it here with his approval. v3 fix 1: Fixed model order 2: Remove manufacturer name from model name 3: Use a hacky but prettier way to get mac address. Signed-off-by: Xiaoning Kang <kangxn@163.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47111 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: Correct WeIO board nameJohn Crispin2015-10-051-1/+1
| | | | | | | | Trivial parch to correct WeIO board name in the system. Signed-off-by: Drasko DRASKOVIC <drasko.draskovic@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47110 3c298f89-4303-0410-b956-a3cf2f4a3e73
* target/mpc85xx: check if 'generic' subtarget for image file ↵John Crispin2015-10-051-2/+5
| | | | | | | | | | | cuImage.tl-wdr4900-v1 Only add 'cuImage.tl-wdr4900-v1' to KERNEL_IMAGES if the selected subtarget is 'generic'. Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47109 3c298f89-4303-0410-b956-a3cf2f4a3e73
* iwinfo: nl80211: add support for reading TX power from netlinkJo-Philipp Wich2015-10-051-2/+2
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47108 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ar71xx: rename firmware for Chinese version of TL-WR941ND v6Rafał Miłecki2015-10-051-2/+3
| | | | | | | | | | | | | It seems there are two *different* versions on TL-WR941ND v6: Chinese and European one. Currently supported by OpenWrt is Chinese one. Rename firmware to make it clear. For details see: http://wiki.openwrt.org/toh/tp-link/tl-wr941nd https://forum.openwrt.org/viewtopic.php?id=59295 Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47107 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix gcc 5 buildMatteo Croce2015-10-042-0/+26
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47106 3c298f89-4303-0410-b956-a3cf2f4a3e73
* lantiq: fix binutils 2.15.1 buildMatteo Croce2015-10-041-1/+1
| | | | git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47105 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: update 4.1 to 4.1.10Hauke Mehrtens2015-10-0441-137/+90
| | | | | | | | | | | | | | | | | | | | Fixes a regression on spi flash devices (upstream commit 1583eaece6fa). Changelogs: * https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.7 * https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.8 * https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.9 * https://www.kernel.org/pub/linux/kernel/v4.x/ChangeLog-4.1.10 096-ipv4-off-by-one-in-continuation-handling-in-proc-net.patch was applied upstream and dropped. Signed-off-by: Mathias Kresin <openwrt@kresin.me> [update from 4.1.9 to 4.1.10] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47104 3c298f89-4303-0410-b956-a3cf2f4a3e73
* toplevel.mk: drop LD_LIBRARY_PATH overridesJo-Philipp Wich2015-10-031-2/+0
| | | | | | | | | | | | | Overriding LD_LIBRARY_PATH for host utilities frequently leads to problems with host executables loading shared libraries from the staging_dir, leading to crashes due to incompatible ABIs. Since most host utilties either embed a proper rpath or are reworked to link statically we do not need the workaround anymore. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47103 3c298f89-4303-0410-b956-a3cf2f4a3e73
* libnl: Install include files into libnl3Felix Fietkau2015-10-021-2/+2
| | | | | | | | | Install header files into same location as pkgconfig/libnl-3.0.pc says: Cflags: -I${includedir}/libnl3 Signed-off-by: Bruno Randolf <br1@einfach.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47102 3c298f89-4303-0410-b956-a3cf2f4a3e73
* iproute2: adapt coexistence layer to new unified pathSteven Barth2015-10-021-5/+5
| | | | | | Signed-off-by: Steven Barth <steven@midlink.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47081 3c298f89-4303-0410-b956-a3cf2f4a3e73
* base-files: sanitize and unify $PATHSteven Barth2015-10-024-5/+5
| | | | | | | | Previously init and hotplug paths were different from console. Signed-off-by: Steven Barth <steven@midlink.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47080 3c298f89-4303-0410-b956-a3cf2f4a3e73
* procd: make nand_do_platform_check check image onlyRafał Miłecki2015-10-021-3/+0
| | | | | | | | | | | Recently all targets have been updated to call nand_do_upgrade directly. It's not needed anymore to leave a magic /tmp/sysupgrade-nand-path mark during image check. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47079 3c298f89-4303-0410-b956-a3cf2f4a3e73
* musl: re-enable des crypto support, fixes pppd MPPE issuesFelix Fietkau2015-10-011-56/+6
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47078 3c298f89-4303-0410-b956-a3cf2f4a3e73
* toolchain/uClibc: add support of uClibc-ngFelix Fietkau2015-10-0126-3/+553
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | uClibc-ng is a spin-off of original uClibc, see http://www.uclibc-ng.org/ We try to regularly add changes from uClibc to uClibc-ng. We even sent patches and bug reports to the uClibc mailing list. The config file is compatible between uClibc-ng 1.0 and uClibc git master. This might change in the future. Our main goal is to provide regularly a stable and tested release to make embedded system developers happy. The main advantage of uClibc-ng over olde good uClibc is regular releases so there's no need to keep tons of patches on top of years old 0.9.33.2 Build-tested for [1] ARM: Sunxi generic [2] MIPS: Netgear WNDR3600/3700/3800 Run-tested for [yet out of the tree] Synopsys Designware ARC AXS101. Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com> Cc: Waldemar Brodkorb <wbx@uclibc-ng.org> Cc: Mathieu Olivari <mathieu@codeaurora.org> Cc: Felix Fietkau <nbd@openwrt.org> Cc: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47077 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ralink: add irq to mt7628 gpio nodeJohn Crispin2015-10-011-0/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47076 3c298f89-4303-0410-b956-a3cf2f4a3e73
* rpcd: update to latest git HEADJohn Crispin2015-10-011-2/+3
| | | | | | | | Provides ubus calls for sysupgrade and password changing. Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47075 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ralink: the mmc driver can now handle CD lines that are active lowJohn Crispin2015-10-011-4/+14
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47074 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ralink: speed selection was broken in spi-mt7621John Crispin2015-10-011-4/+5
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47073 3c298f89-4303-0410-b956-a3cf2f4a3e73
* quilt: add further relocatability fixesJo-Philipp Wich2015-09-292-4/+58
| | | | | | | | | Prevent quilt's build system from generating useless compat wrappers and hardcoded absolute utility paths to binaries in staging_dir/host/. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47070 3c298f89-4303-0410-b956-a3cf2f4a3e73
* prereq-build: test availability of Perl Thread::Queue moduleJo-Philipp Wich2015-09-291-0/+4
| | | | | | | | This is needed for building automake. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47069 3c298f89-4303-0410-b956-a3cf2f4a3e73
* uml: backport another upstream patch to fix compile errorsFelix Fietkau2015-09-282-1/+95
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47067 3c298f89-4303-0410-b956-a3cf2f4a3e73
* base-files: add a dependency on fstoolsFelix Fietkau2015-09-281-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47066 3c298f89-4303-0410-b956-a3cf2f4a3e73
* hostapd: check for banned client on association eventRafał Miłecki2015-09-281-0/+26
| | | | | | | | | | | When using FullMAC drivers (e.g. brcmfmac) we don't get mgmt frames so check for banned client in probe request handler won't ever be used. Since cfg80211 provides us info about STA associating let's put a check there. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47064 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mt76: update to the latest version, fixes some aggregation issuesFelix Fietkau2015-09-271-2/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47063 3c298f89-4303-0410-b956-a3cf2f4a3e73
* uml: fix build with gcc 5Felix Fietkau2015-09-271-0/+44
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47062 3c298f89-4303-0410-b956-a3cf2f4a3e73
* uml: update to linux 4.1Felix Fietkau2015-09-277-3977/+63
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47061 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: backport patch setting TX power in interface infoRafał Miłecki2015-09-271-0/+37
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47059 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: describe 300-fork_cacheflush.patch & 310-no_highpage.patchRafał Miłecki2015-09-272-0/+20
| | | | | | | | These were initially commited in r9285. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47058 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: describe 160-kmap_coherent.patchRafał Miłecki2015-09-271-0/+8
| | | | | | | | It was initially commited in r6642. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47057 3c298f89-4303-0410-b956-a3cf2f4a3e73
* brcm47xx: describe 610-pci_ide_fix.patchRafał Miłecki2015-09-271-0/+27
| | | | | | | | It was initially commited in r20924. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47056 3c298f89-4303-0410-b956-a3cf2f4a3e73
* igmpproxy: fix spurious restarts on interface events, pass used netdevs to ↵Felix Fietkau2015-09-261-1/+5
| | | | | | | | procd instead Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47055 3c298f89-4303-0410-b956-a3cf2f4a3e73
* netifd: update to the latest version, fixes spurious client isolation in ↵Felix Fietkau2015-09-261-2/+2
| | | | | | | | unbridged AP configurations (#20574) Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47053 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bcm53xx: add early support for Linksys EA6300 V1Rafał Miłecki2015-09-263-0/+96
| | | | | | Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47052 3c298f89-4303-0410-b956-a3cf2f4a3e73
* bison: replace the yacc script with one that does not hardcode the path ↵Felix Fietkau2015-09-262-0/+7
| | | | | | | | (fixes #20605) Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47050 3c298f89-4303-0410-b956-a3cf2f4a3e73
* tools/patch: enable parallel buildFelix Fietkau2015-09-261-0/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47049 3c298f89-4303-0410-b956-a3cf2f4a3e73
* firewall: allow DHCPv6 traffic to/from fc00::/6 instead of fe80::/10Jo-Philipp Wich2015-09-251-2/+2
| | | | | | | | | | There is no RFC requirement that DHCPv6 servers must reply with a link local address and some ISP servers in the wild appear to using addresses in the ULA range to send DHCPv6 offers. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47048 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: crypto: fix ubsec_ssb.c compilation with 4.0+Rafał Miłecki2015-09-251-1/+1
| | | | | | | | | SSB_DEVTABLE_END was removed in 4.0 by upstream commit 673e2baaa6d9 ("treewide: Remove unnecessary SSB_DEVTABLE_END macro"). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47047 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: backport some SPI layer improvements from 4.1 to 3.18, significantly ↵Felix Fietkau2015-09-243-0/+314
| | | | | | | | improves flash speed on ramips Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47045 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mt76: update to the latest version, adds performance improvementsFelix Fietkau2015-09-241-2/+2
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47043 3c298f89-4303-0410-b956-a3cf2f4a3e73
* ath9k: fix handling of tx headroom for padding (fixes #20556)Felix Fietkau2015-09-244-4/+26
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47042 3c298f89-4303-0410-b956-a3cf2f4a3e73
* mac80211: fix a few issues with fast-xmit supportFelix Fietkau2015-09-242-0/+68
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47041 3c298f89-4303-0410-b956-a3cf2f4a3e73
* kernel: remove old "rootfs" splitterRafał Miłecki2015-09-243-78/+1
| | | | | | | | | | | | | A year ago I made this old splitter obsolete (see r42828), it's time to completely remove it now. For all this time we got these warnings: "Dedicated partitioner didn't create "rootfs_data" partition, please fill a bug report!" and "Support for built-in "rootfs_data" splitter will be removed, please use CONFIG_MTD_SPLIT_SQUASHFS_ROOT" but I'm not aware of any bug reports related to that. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47040 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: add platform_pre_upgrade for sysupgradeRafał Miłecki2015-09-241-0/+4
| | | | | | | | | | | | | | | | | We're in process of cleaning nand_do_platform_check. Currently it leaves a special mark in /tmp/sysupgrade-nand-path triggering some diffent code path in nand_upgrade_stage1. This can be a bit confusing. The plan is to have the check function only check the image and nothing else. Then platform code (platform_pre_upgrade) should trigger NAND specific upgrade path. This is what this patch implements. This follows all other targets making it finally possible to change nand_do_platform_check. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47039 3c298f89-4303-0410-b956-a3cf2f4a3e73
* oxnas: drop some unused sysupgrade codeRafał Miłecki2015-09-241-9/+0
| | | | | | | | | | | | First of all platform_do_upgrade_phase2 doesn't seem to be defined anywhere. Other than that platform_do_upgrade is not likely to be ever called. There is a call to nand_do_platform_check which triggers nand_upgrade_stage1 call with "exit 0" in it. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Daniel Golle <daniel@makrotopia.org> git-svn-id: svn://svn.openwrt.org/openwrt/trunk@47038 3c298f89-4303-0410-b956-a3cf2f4a3e73
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 12:03:10 +0000