aboutsummaryrefslogtreecommitdiffstats
Commit message (Collapse)AuthorAgeFilesLines
* Mark the GIGABYTE GA-8I945GZME-RH and SST SST25LF040A as supportedUwe Hermann2011-09-072-1/+2
| | | | | | | | | | | | | Success report: http://www.flashrom.org/pipermail/flashrom/2011-June/006797.html lspci and other info: http://www.flashrom.org/pipermail/flashrom/2010-August/004531.html Corresponding to flashrom svn r1431. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Add Intel Tunnel Creek chipset support, mark it as testedIngo Feldschmid2011-09-071-1/+45
| | | | | | | | | | | | | | | | | | | | Intel's Tunnel Creek chipset supports both an SPI and an LPC bus. Set the chipset table entry for Tunnel Creek to the new function enable_flash_tunnelcreek(), which will read the hardware straps and return support for the bus that has been used for booting. This function uses ich_init_spi() with ich_generation set to 7 for initializing the SPI bus if necessary. SPI functionality tested on actual hardware, Tunnel Creek LPC interface not tested yet (missing hardware for that). Log file / success report: http://www.flashrom.org/pipermail/flashrom/2011-September/007823.html Corresponding to flashrom svn r1430. Signed-off-by: Ingo Feldschmid <ifel@msc-ge.com> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Kill all exit() calls in chipset_enable.cTadas Slotkus2011-09-061-5/+4
| | | | | | | Corresponding to flashrom svn r1429. Signed-off-by: Tadas Slotkus <devtadas@gmail.com> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Fix linux_spi.c build on 32bit systemsUwe Hermann2011-09-061-2/+2
| | | | | | | Corresponding to flashrom svn r1428. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Add support for the Linux SPI subsystem (spidev)Sven Schnelle2011-09-034-0/+180
| | | | | | | | | | | | | | | | | | | | | | See http://www.kernel.org/doc/Documentation/spi/spidev for an introduction. Usage is as follows: flashrom -p linux_spi:dev=/dev/spidevX.Y where X is the bus number, and Y device. It accepts an optional parameter 'speed' which allows to set the SPI clock speed in kHz. Tested on an Atmel AVR32AP7000 board (NGW100 Network Gateway Kit), see below, which was used to program a ThinkPad X60, but it should work on every other Linux system, too. http://www.atmel.com/dyn/products/tools_card.asp?tool_id=4102) Corresponding to flashrom svn r1427. Signed-off-by: Sven Schnelle <svens@stackframe.org> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Introduce ERROR_FATAL, abort upon failed chipset enablesTadas Slotkus2011-09-033-2/+10
| | | | | | | Corresponding to flashrom svn r1426. Signed-off-by: Tadas Slotkus <devtadas@gmail.com> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Add a bunch of new/tested stuff and various small changes 7Sylvain "ythier" Hitier2011-09-038-28/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - add Asus Crosshair IV Extreme to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-August/007640.html - add Biostar N68S3+ to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-September/007788.html - add P7H55-M LX to the list of supported boards although flashrom works correctly, it is marked as not ok, because flashing the vendor image will break the LAN interface. - add GA-X58A-UD7 to the list of supported boards http://paste.flashrom.org/view.php?id=739 - add Asus P4P800-VM to print.c (has a working board enable) - add Asus K8V-X to print.c reported by florz http://paste.flashrom.org/view.php?id=742 - add Intel D865GLC to print.c as non-working (ICH5 with BIOS lock enable) reported by jmd on IRC http://paste.flashrom.org/view.php?id=775 - add Intel DH67CF to print.c as non-working (H67 with BIOS lock enable and locked ME region) http://www.flashrom.org/pipermail/flashrom/2011-September/007789.html - add ECS P4M800PRO-M (V1.0A) to the list of supported boards reported by dweg on IRC (hot flashed a SST49LF040B, original was W39V040B) - add X8DTU-6TF+ to print.c (needs ME unlocking) http://www.flashrom.org/pipermail/flashrom/2011-August/007553.html - add Shuttle FH67 (used in the SH67H3 barebone) to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-August/007749.html - add Tyan S2912 to the list of supported boards reported by erlan on IRC - add ZOTAC GeForce 8200 to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-August/007612.html - mark AT25DF321A as TEST_OK_PROBE http://www.flashrom.org/pipermail/flashrom/2011-August/007553.html - mark 28F001BN/BX-T as TEST_OK_PR http://www.flashrom.org/pipermail/flashrom/2011-July/007208.html - rename MX29F002 http://patchwork.coreboot.org/patch/2794/ - mark SST39SF040 as fully tested reported by Florian 'florz' Zumbiehl http://paste.flashrom.org/view.php?id=742 - mark SST49LF040B as fully tested reported by dweg on IRC and later by Armin on the ml: http://www.flashrom.org/pipermail/flashrom/2011-August/007764.html - mark H55 chipset as OK http://www.flashrom.org/pipermail/flashrom/2011-July/007432.html - mark H67 chipset as OK http://www.flashrom.org/pipermail/flashrom/2011-August/007749.html - mark a MCP61 version as OK http://www.flashrom.org/pipermail/flashrom/2011-September/007788.html - add preliminary X79 (patsburg) PCI IDs 0x1d40 was reported already as working (not archived in our pipermail?) http://marc.info/?l=flashrom&m=130683026218257&w=2 - mark "82557/8/9/0/1 Ethernet Pro 100" in nicintel.c as working http://www.flashrom.org/pipermail/flashrom/2011-August/007480.html - rename some chips that had gratuitous "probing" suffixes: - SST25VF010.REMS - SST25VF040.REMS - M25P05.RES - M25P10.RES some other chip names with suffixes are needed due to lack of support for multiple probe functions per chip. this is explained here: http://www.flashrom.org/pipermail/flashrom/2011-August/007597.html - remove unneeded nicintel_spi-related function declarations in programmer.h - typos and whitespace fixes - fix Asus P4P800-E Deluxe detection The original board enable was added before DMI matching and used the IDs of a Promise controller as secondary PCI ID set. The controller could be disabled in the BIOS which would make the board not match. This patch uses the SMBus controller instead and adds a DMI pattern. This was Tested-by: Michael Schneider <vdrportal_midas at gmx dot de> Corresponding to flashrom svn r1425. - add "Sealed-case PC" to the list of chassis type (as indicating "not a laptop") This is Acked-by: Idwer Vollering <vidwer@gmail.com> the fix for the typo unusued -> unused is Signed-off-by: Sylvain "ythier" Hitier <sylvain.hitier@gmail.com> everything else is Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> And everything was reviewed and Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Shorten some board enable related function namesCarl-Daniel Hailfinger2011-08-315-21/+20
| | | | | | | Corresponding to flashrom svn r1424. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Fix printing of the Boot BIOS Straps on Intel chipsetsStefan Tauner2011-08-271-48/+81
| | | | | | | | | | | | | | | | | | | | | | | | The meaning of the bits involved has changed several times in the past. This patch takes these changes into account and hence fixes the output of the pretty printing of GCS on all SPI-supported Intel chipsets that are not ICH7 or NM10 (the latter were unaffected, because the defaults were correct). This patch also allows to differentiate Ibex Peak and Cougar Point chipsets from the earlier chipset series (ICH10) by adding new wrapper functions that set "ich_generation" to 11 and 12 respectively. This should not change behavior outside of enable_flash_ich_dc_spi, because the code path for ich_generation >=9 is equal. alternatively we could just remove the pretty printing of GCS and just output the bits involved. i would like to keep the pch differentiation anyway though, because i feel it will become handy in the future. tested on my QS57-based thinkpad (probe + partial read) Corresponding to flashrom svn r1423. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Add AMD Hudson chipset-enableWang Qing Pei2011-08-262-2/+6
| | | | | | | | | | AMD Hudson has different vendor/device IDs than AMD SBx00, handle that properly. Corresponding to flashrom svn r1422. Signed-off-by: Wang Qing Pei <wangqingpei@gmail.com> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Mark the AMD Am29LV008BB chip as fully testedUwe Hermann2011-08-251-1/+1
| | | | | | | | | | Thanks Mattias Mattsson <vitplister@gmail.com> for the report. http://www.flashrom.org/pipermail/flashrom/2011-July/007423.html Corresponding to flashrom svn r1421. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Add support for the Sharp LH28F008BJT-BTLZ1 chipMattias Mattsson2011-08-253-0/+86
| | | | | | | | | | Tested by Mattias Mattsson <vitplister@gmail.com> on a PowerPC box. Corresponding to flashrom svn r1420. Signed-off-by: Mattias Mattsson <vitplister@gmail.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Add board enable for ASUS P5LP-LEMichael Karcher2011-08-252-0/+8
| | | | | | | | | | | | | | Based on the REing of Michael Karcher and a good guess of Idwer Vollering. Corresponding to flashrom svn r1419. Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Tested-by: Leon Zhang <leoncamel at gmail.com> http://www.coreboot.org/pipermail/flashrom/2010-August/004500.html Tested-by: medhi <nefkongo@hotmail.com> http://paste.flashrom.org/view.php?id=779 Acked-by: Idwer Vollering <vidwer@gmail.com>
* Makefile: Fix MinGW build, improve output with bogus CCUwe Hermann2011-08-201-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | As per IRC discussion, the "ARCH :=" line should be moved after any lines which set CC, as it uses CC itself. This fixes the MinGW build. Also, add a "2>/dev/null" in the "ARCH :=" as per suggestion from Stefan Tauner to improve the output in the case CC is bogus: Before: $ make CC=foo /bin/sh: foo: not found Checking for a C compiler... not found. make: *** [compiler] Error 1 After: $ make CC=foo Checking for a C compiler... not found. make: *** [compiler] Error 1 Corresponding to flashrom svn r1418. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Move the main() function from flashrom.c to cli_classic.cUwe Hermann2011-08-203-9/+1
| | | | | | | | | | | | | | | The file flashrom.c is part of libflashrom and should thus not contain a main() function, that would break compilation of all frontends using libflashrom. Also, cli_classic.c is the right place anyway, as it's the main() of the CLI tool. Rename the simple wrapper cli_classic() in cli_classic.c to main(), as it's not really needed. Corresponding to flashrom svn r1417. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Makefile: fix and simplify test program compilationsStefan Tauner2011-08-181-33/+61
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This was totally broken due to the make's shell function's temporal behavior. quote from the gnu make documentation (http://www.gnu.org/s/hello/manual/make/Shell-Function.html): "The commands run by calls to the shell function are run when the function calls are expanded" we have used the shell function to echo the test programs to a file. the file name used was equal for all tests and was overwritten for each test. the result was that all tests (in a single target?) used the last test program because the echoing of the test programs was done before all test compilations(!) see my mail for details: http://lists.gnu.org/archive/html/bug-make/2011-08/msg00010.html also the branching for testing ifeq ($(CONFIG_FT2232_SPI), yes) was unnecessarily complicated. in my approach here i am using verbatim variables (allows to define even complex test programs in the makefile without jumping through hoops) that get exported to environment variables (via "export", reference afterwards with "$$<varname>"). i have also added the missing redirection of stderr to the compiler test and changed the definition of ARCH to use simple expansion (:=). the latter is still wrong, because it uses $(CC) before we check if a compiler is installed... makes the compiler check pretty much useless. The simple expansion just reduces the number of errors printed to 1. Corresponding to flashrom svn r1416. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Add support for the SST25LF080A flash chipZeus Castro2011-08-171-30/+60
| | | | | | | | | | | | | Based on the definition of SST25LF040A and the public datasheet available here: http://www.sst.com/dotAsset/40316.pdf Also, move the SST25LF040A up to keep the list ordered alphabetically (while removing the ".RES" suffix). Corresponding to flashrom svn r1415. Signed-off-by: Zeus Castro <thezeusjuice@gmail.com> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Remove unneeded inclusions of chipdrivers.hStefan Tauner2011-08-1613-12/+2
| | | | | | | | | | | | | | | | | | | | | | This is related to the spi split patch as discussed in: http://www.flashrom.org/pipermail/flashrom/2010-February/thread.html#2364 the old commit (r914) log notes: "Some of the spi programmer drivers required chipdrivers.h, needs fixing later: it87spi.c ichspi.c sb600spi.c wbsio_spi.c buspirate_spi.c ft2232spi.c bitbang_spi.c dediprog.c" there still remain a few cases where chipdrivers.h is needed: dediprog.c (spi_read_chunked and spi_write_chunked) it87spi.c (due to spi_write_enable and spi_read_status_register) wbsio_spi.c (spi_programmer registration only) besides that, there are also non-spi files that do not need it. also, add flash.h to chipdrivers.h because it uses some types of it and remove flashchips.h from print.c Corresponding to flashrom svn r1414. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Fixup of r1397Carl-Daniel Hailfinger2011-08-1511-40/+59
| | | | | | | | | | | | | | - Mixing uninitialized and initialized local variables leads to confusion. - ft2232_spi error cases should have gotten some error handling, and that's the reason the curly braces were there. - Fixing typos/wording in some places would have been nice given that those places were touched anyway. Corresponding to flashrom svn r1413. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* ft2232_spi: add support for the Dangerous Prototypes Bus BlasterSteve Markgraf2011-08-122-4/+10
| | | | | | | | | | | | | | | | Add support for the Dangerous Prototypes Bus Blaster (v1/v2). The new model is called "busblaster". So far only v2 has been tested, but since both v1 and v2 emulate a Amontec JTAGKEY in the default configuration, it is assumed that v1 should work fine as well. Information about the Busblaster can be found at: http://dangerousprototypes.com/docs/Bus_Blaster Corresponding to flashrom svn r1412. Signed-off-by: Steve Markgraf <steve@steve-m.de> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Add board enable for ASUS P5GD2 PremiumJoshua Roys2011-08-112-1/+4
| | | | | | | | | | | | | | | | | | | | | | This is based on Joshua's patch, but with a DMI pattern, contrary to http://www.flashrom.org/pipermail/flashrom/2010-September/004745.html Rationale: although it looks like all P5GD2/C* might use the same board enable (intel_ich_gpio21_raise), we need to add the variants individually as long as we don't have enough reports to make a better guess. This also guarantees correct output of flashrom -L and -z and on activation of the board enable - not like this: http://www.flashrom.org/pipermail/flashrom/attachments/20100930/2286e5d1/attachment-0003.txt Success report: http://www.flashrom.org/pipermail/flashrom/2010-August/004555.html Also, fix last commit by adding a missing comma. Corresponding to flashrom svn r1411. Tested-by: Roberto Malinverni Signed-off-by: Joshua Roys <roysjosh@gmail.com> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Add (untested) board enable for Asus P5LD2Joshua Roys2011-08-112-0/+3
| | | | | | | | | | | | | | | | | | There are numerous other variants of the P5LD2 which vary wildly not only in PCB layout but also in northbridges used, number of PCI, PCI-E and DIMM slots etc. This one is for the plain P5LD2 without any suffixes. This patch is essentially a rebased version of Joshua's patch, which was never tested (user did not reply). I have added additional PCI IDs and the DMI pattern and also changed the status to NT. An entry in the print.c table was also added. http://www.flashrom.org/pipermail/flashrom/2010-October/005080.html Corresponding to flashrom svn r1410. Signed-off-by: Joshua Roys <roysjosh@gmail.com> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* ichspi.c: refactor filling and reading the fdata/spid registersStefan Tauner2011-08-091-78/+57
| | | | | | | | | | | | - add ich_fill_data to fill the chipset registers from an array - add ich_read_data to copy the data from the chipset register into an array - replace the existing code with calls to those functions - minor cosmetic changes Corresponding to flashrom svn r1409. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Add a board enable for ASUS A8M2N-LA (HP OEM "NodusM3-GL8E")Stefan Tauner2011-08-073-1/+4
| | | | | | | | | | | It is based on Joshua Roys' RE. http://www.flashrom.org/pipermail/flashrom/2011-August/007504.html Corresponding to flashrom svn r1408. Tested-by: Márton Miklós Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Fix the A8N-SLI Deluxe board enableStefan Tauner2011-08-062-2/+2
| | | | | | | | | | | | | | | | | | | | | | Long story short: - the A8N in print.c should be A8N-SLI Deluxe as documented - the A8N-SLI Deluxe board enable needs a DMI pattern, else it will get executed on the A8N-SLI Premium unnecessarily. http://www.flashrom.org/pipermail/flashrom/2010-August/004310.html the DMI string is taken from an ubuntu bug report (a real dmidecode or flashrom output was not found). https://bugs.launchpad.net/ubuntu/+source/linux/+bug/807980 - the other A8N-SLI variants seem to work without the board enable A8N-SLI Premium: http://www.flashrom.org/pipermail/flashrom/2010-August/004310.html A8N-SLI: http://www.coreboot.org/pipermail/coreboot/2009-June/049107.html http://www.coreboot.org/pipermail/coreboot/2009-May/049002.html Corresponding to flashrom svn r1407. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Fix the EP-8NPA7I (for the last time hopefully)Stefan Tauner2011-08-062-4/+5
| | | | | | | | | | | | | | | | - retag it as OK (tested by Jonathan Kollasch when he wrote it) http://patchwork.coreboot.org/patch/2106/ - add a line with identical pci ids but a different DMI pattern, so that EP-9NPA7I is also matched. combining multiple boards in one line is problematic due to print.c's detection of board enables - so dont bother for now. http://www.flashrom.org/pipermail/flashrom/2011-June/006878.html See previous commit for additional information. Corresponding to flashrom svn r1406. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Clear byte 0x92 of the LPC bridge for all CK804 (and MCP51) chipsetsJonathan Kollasch2011-08-061-0/+6
| | | | | | | | | | | | | | | | | | | | | | | The OEM BIOS on the EPoX EP-8PA7I and a number of other boards clear byte 0x92 in the LPC bridge configuration space. Do the same for all CK804 chips, assuming this to be some sort of chipset-generic write-enable. Currently the same chipset enable is used for MCP51 (nForce 430). There have been reports of successful writes with its variations (e.g. A8N-LA (Nagami-GL8E)), but they were not tagged as OK. Due to the new "unsupported chipset"-message we will get success reports in the case this patch does not break anything on the MCP51-based boards. See also: http://www.flashrom.org/pipermail/flashrom/2011-July/007252.html http://patchwork.coreboot.org/patch/3176/ Corresponding to flashrom svn r1405. Signed-off-by: Jonathan Kollasch <jakllsch@kollasch.net> Acked-by: Joshua Roys <roysjosh@gmail.com> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Introduce msg_*dbg2Stefan Tauner2011-08-043-3/+10
| | | | | | | Corresponding to flashrom svn r1404. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Rephrase warnings in chipset_enable.cStefan Tauner2011-08-041-22/+22
| | | | | | | Corresponding to flashrom svn r1403. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Switch to AAI for some more SST chipsJoshua Roys2011-08-011-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | Enable AAI for: SST25VF016B SST25VF040B{,.REMS} SST25VF080B Chips that support AAI via a different opcode are annotated with a comment: SST25VF040.REMS SST25LF040A.RES SST25VF080B Tested-by: Joshua Roys <roysjosh@gmail.com> Write time (w/erase) went from 46 s to 21 s. SST25VF016B Tested-by: Noé Rubinstein <nrubinstein@avencall.com> Write time (w/erase) on a dediprog went from 143 mins to 56 mins. Corresponding to flashrom svn r1402. Signed-off-by: Joshua Roys <roysjosh@gmail.com> Rebased and Acked-by: Noé Rubinstein <nrubinstein@avencall.com>
* Use __func__ instead of __FUNCTION__ as we do elsewhereUwe Hermann2011-07-291-14/+12
| | | | | | | | | | | | The __func__ variant is standardized in C99 and recommended to be used instead of __FUNCTION__ in the gcc info page. See also r711 where we did the same change. Corresponding to flashrom svn r1401. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Make flashrom build on PPC/PowerPC with just "make"Uwe Hermann2011-07-291-0/+34
| | | | | | | | | | Build-tested in a QEMU ppc (Debian) image, and by Andrew Morgan <ziltro@ziltro.com> on real hardware. Corresponding to flashrom svn r1400. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Andrew Morgan <ziltro@ziltro.com>
* Extract spi_prettyprint_status_register_amic_a25_srwdStefan Tauner2011-07-291-8/+10
| | | | | | | | | | Extract spi_prettyprint_status_register_amic_a25_srwd from spi_prettyprint_status_register_amic_a25l* functions Corresponding to flashrom svn r1399. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* manpage: Document all ft2232_spi and serprog variantsUwe Hermann2011-07-281-8/+11
| | | | | | | Corresponding to flashrom svn r1398. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Random whitespace and coding-style fixesUwe Hermann2011-07-2820-523/+523
| | | | | | | | | | | | Also, indentation fixes, e.g. due to conversion to msg_*, use ARRAY_SIZE where possible, wrap overly long line, etc. Compile-tested. There should be no functional changes. Corresponding to flashrom svn r1397. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Rename CHIP_BUSTYPE_FOO to BUS_FOOCarl-Daniel Hailfinger2011-07-2722-348/+348
| | | | | | | | | It's shorter to type, and we have less problems with the 80 column limit. Corresponding to flashrom svn r1396. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Increase flashrom release number to 0.9.4Carl-Daniel Hailfinger2011-07-261-1/+1
| | | | | | | | | Corresponding to flashrom svn r1394. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de>
* Add a bunch of new/tested stuff and various small changes 6Stefan Tauner2011-07-264-6/+11
| | | | | | | | | | | | | | | | | - add J-7BXAN to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-July/007397.html - fix urls, typos, whitespace etc. - fix counting of supported chips in the wiki output Corresponding to flashrom svn r1393. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> the last one is Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> everything else is Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Fix output of erase_and_write_flash and surroundingsCarl-Daniel Hailfinger2011-07-261-13/+16
| | | | | | | | | | | | See http://www.flashrom.org/pipermail/flashrom/2011-July/007220.html for a discussion about the details. Corresponding to flashrom svn r1392. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Fix Winbond W29EE011, W29EE012, W29C010M, W29C011A probingCarl-Daniel Hailfinger2011-07-262-28/+31
| | | | | | | | | | | | According to the datasheets probe_w29ee011 is the only valid probe function for those chips, but we have reports where those chips were only detected with probe_jedec, and thus we assume that our datasheets only cover an earlier stepping. Corresponding to flashrom svn r1391. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Be more refined regarding DMI chassis typesStefan Tauner2011-07-262-16/+43
| | | | | | | | | | | | | | | | | | | | | We had broken laptops in the past that were not detected as such because their DMI chassis-type was either undefined/out-of-spec, or set to 'other' or 'unknown'. this patch tries to mitigate this problem as follows: - if the DMI chassis-type clearly identifies the system as laptop/notebook/mobile platform then nothing changes: the user gets the laptop warning without a hint to the force switch. - if the DMI chassis-type is not specific enough, we warn the user similarly, but tell them the switch. to reduce the number of false positives i have added a few new chassis types that we have encountered in the last months to the list. Corresponding to flashrom svn r1390. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Fix ICH FWH IDSEL setting with the fwh_idsel= internal programmer parameterCarl-Daniel Hailfinger2011-07-252-7/+44
| | | | | | | | | | | The code took 32 bits of input and wrote them to an 48 bit register, duplicating some values. Document the fwh_idsel= parameter in the man page. Corresponding to flashrom svn r1389. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Enforce compile-time errors in satamv and atahp for non-x86 targetsAndrew Morgan2011-07-252-0/+11
| | | | | | | | | | | Satamv and atahpt require PCI port I/O which isn't currently supported on any architecture except x86/x86_64. Generate the same compiler error as other programmer drivers. Corresponding to flashrom svn r1388. Signed-off-by: Andrew Morgan <ziltro@ziltro.com> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Random manpage improvements and updatesUwe Hermann2011-07-251-14/+24
| | | | | | | Corresponding to flashrom svn r1387. Signed-off-by: Uwe Hermann <uwe@hermann-uwe.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* Add a bunch of new/tested stuff and various small changes 5Stefan Tauner2011-07-257-29/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - mark EN25F80 as fully tested http://www.flashrom.org/pipermail/flashrom/2011-July/007329.html - mark W25Q16 as fully tested http://www.flashrom.org/pipermail/flashrom/2011-July/007151.html - mark W39V040A as fully tested http://www.flashrom.org/pipermail/flashrom/2011-July/007161.html - mark Pm25LV040 as fully tested reported by TL1 on IRC - mark W49F002U/N as fully tested http://paste.flashrom.org/view.php?id=733g - mark W39V080FA as fully tested http://www.flashrom.org/pipermail/flashrom/2011-July/007225.html - add ASUS P4S533-X to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-July/007200.html - add ASUS M4A785TD-V EVO to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-July/007329.html - add GA-945PL-S3P (rev. 6.6) to the list of supported boards reported by TL1 on IRC - add MS-7142 (K8MM-V) to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-July/007161.html - add MS-7369 (K9N Neo V2) to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-July/007181.html - add X7DBT-INF to the list of supported boards http://www.flashrom.org/pipermail/flashrom/2011-July/007225.html - mark SiS 645DX chipset enable as OK http://www.flashrom.org/pipermail/flashrom/2011-July/007200.html - mark SiS 651 chipset enable as OK http://paste.flashrom.org/view.php?id=733 - move intel_ich_gpio34_raise to the correct line(s) - change the output of unlock_w39_fwh_block from 0x%x to 0x%08x - fix output for untested chipset enables (missing space) - reorder the board enable in print.c entry for GA-8SIMLH added in r1385. - minor other fixes - fix output for multiple found flash chips by adding quotes and commas - similarly fix output of "Found/Assuming" chips Corresponding to flashrom svn r1386. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> the last two points are Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> everything else is Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Add support for the GIGABYTE GA-8SIMLH boardMichael Karcher2011-07-252-4/+6
| | | | | | | | | | | | | | | | | The usage of the GPIO output register as bitmap can be confirmed from the vendor board enable code, so the comment has been deleted. It really is (1<<gpionumber). flashrom -V: http://paste.flashrom.org/view.php?id=728 lspci: http://paste.flashrom.org/view.php?id=729 superiotool: http://paste.flashrom.org/view.php?id=730 test report: http://paste.flashrom.org/view.php?id=733 Corresponding to flashrom svn r1385. Signed-off-by: Michael Karcher <flashrom@mkarcher.dialup.fu-berlin.de> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Add support for EN25Q(H) series SPI flash chipsDavid Hendricks2011-07-242-37/+260
| | | | | | | | | | | | | | | | - EN25Q40 - EN25Q80 - EN25Q16 (half-evil twin of already supported EN25D16, hence merged) - EN25Q32(A/B) - EN25Q64 - EN25Q128 - EN25QH16 Corresponding to flashrom svn r1384. Signed-off-by: David Hendricks <dhendrix@google.com> Acked-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at>
* Man page fixesCarl-Daniel Hailfinger2011-07-241-32/+74
| | | | | | | | | | | | - Finish dummy programmer description - Add satamv programmer - Merge it87spi programmer into internal section - Cosmetics Corresponding to flashrom svn r1383. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net> Acked-by: Uwe Hermann <uwe@hermann-uwe.de>
* Mark some ck804 boards as not workingStefan Tauner2011-07-242-2/+4
| | | | | | | | | | | | | | P5N-E SLI, EP-8NPA7I and EP-9NPA7I all need at least this patch: http://patchwork.coreboot.org/patch/2125/ the P5N-E also needs a board enable: http://patchwork.coreboot.org/patch/3298/ mark the boards as not working until those are merged. Corresponding to flashrom svn r1382. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
* ichspi.c: do not print PBR[3] for ICH7 because it does not existStefan Tauner2011-07-241-1/+1
| | | | | | | | | | | | | Intel document 307013 (ICH7 datasheet) section 21.1.9 does only define PBR[0] (at SPIBAR + 60h) to PBR[2] (SPIBAR + 68h). SPIBAR + 6Ch and following are not defined, but we were printing them as PBR[3] anyway. i could not find any references to PBR[3] in documentation of other related chips (NM10, atom e6xx) either, hence kill it. Corresponding to flashrom svn r1381. Signed-off-by: Stefan Tauner <stefan.tauner@alumni.tuwien.ac.at> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006@gmx.net>
generated by cgit v1.2.3 (git 2.25.1) at 2025-04-25 00:38:40 +0000