diff options
Diffstat (limited to 'Demos/Device/ClassDriver')
85 files changed, 1984 insertions, 265 deletions
diff --git a/Demos/Device/ClassDriver/AudioInput/AudioInput.c b/Demos/Device/ClassDriver/AudioInput/AudioInput.c index 867a09eef..953ecf8b6 100644 --- a/Demos/Device/ClassDriver/AudioInput/AudioInput.c +++ b/Demos/Device/ClassDriver/AudioInput/AudioInput.c @@ -94,7 +94,7 @@ void SetupHardware(void) USB_Init(); /* Start the ADC conversion in free running mode */ - ADC_StartReading(ADC_REFERENCE_AVCC | ADC_RIGHT_ADJUSTED | MIC_IN_ADC_MUX_MASK); + ADC_StartReading(ADC_REFERENCE_AVCC | ADC_RIGHT_ADJUSTED | ADC_GET_CHANNEL_MASK(MIC_IN_ADC_CHANNEL)); } /** ISR to handle the reloading of the data endpoint with the next sample. */ diff --git a/Demos/Device/ClassDriver/AudioInput/AudioInput.h b/Demos/Device/ClassDriver/AudioInput/AudioInput.h index 6bf5e882a..6af4a1efe 100644 --- a/Demos/Device/ClassDriver/AudioInput/AudioInput.h +++ b/Demos/Device/ClassDriver/AudioInput/AudioInput.h @@ -42,21 +42,15 @@ #include <avr/power.h> #include <avr/interrupt.h> - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Buttons.h> #include <LUFA/Drivers/Peripheral/ADC.h> #include <LUFA/Drivers/USB/USB.h> #include "Descriptors.h" + #include "Config/AppConfig.h" /* Macros: */ - /** ADC channel number for the microphone input. */ - #define MIC_IN_ADC_CHANNEL 2 - - /** ADC channel MUX mask for the microphone input. */ - #define MIC_IN_ADC_MUX_MASK ADC_CHANNEL2 - /** Maximum audio sample value for the microphone input. */ #define SAMPLE_MAX_RANGE 0xFFFF diff --git a/Demos/Device/ClassDriver/AudioInput/AudioInput.txt b/Demos/Device/ClassDriver/AudioInput/AudioInput.txt index fea95b0c8..dfa9362c2 100644 --- a/Demos/Device/ClassDriver/AudioInput/AudioInput.txt +++ b/Demos/Device/ClassDriver/AudioInput/AudioInput.txt @@ -72,14 +72,19 @@ * <td><b>Description:</b></td> * </tr> * <tr> + * <td>MIC_IN_ADC_CHANNEL</td> + * <td>AppConfig.h</td> + * <td>Sets the ADC channel used by the demo for the input audio samples from an attached microphone.</td> + * </tr> + * <tr> * <td>USE_TEST_TONE</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, this alters the demo to produce a square wave test tone when the first board button is pressed * instead of sampling the board microphone.</td> * </tr> * <tr> * <td>MICROPHONE_BIASED_TO_HALF_RAIL</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, this alters the demo so that the half VCC bias of the microphone input is subtracted.</td> * </tr> * </table> diff --git a/Demos/Device/ClassDriver/AudioInput/Config/AppConfig.h b/Demos/Device/ClassDriver/AudioInput/Config/AppConfig.h new file mode 100644 index 000000000..7702e259a --- /dev/null +++ b/Demos/Device/ClassDriver/AudioInput/Config/AppConfig.h @@ -0,0 +1,51 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief Application Configuration Header File + * + * This is a header file which is be used to configure some of + * the application's compile time options, as an alternative to + * specifying the compile time constants supplied through a + * makefile or build system. + * + * For information on what each token does, refer to the + * \ref Sec_Options section of the application documentation. + */ + +#ifndef _APP_CONFIG_H_ +#define _APP_CONFIG_H_ + + #define MIC_IN_ADC_CHANNEL 2 + + #define MICROPHONE_BIASED_TO_HALF_RAIL + #define USE_TEST_TONE + +#endif
\ No newline at end of file diff --git a/Demos/Device/ClassDriver/AudioInput/Config/LUFAConfig.h b/Demos/Device/ClassDriver/AudioInput/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/AudioInput/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/AudioInput/Descriptors.h b/Demos/Device/ClassDriver/AudioInput/Descriptors.h index 359a28730..a3f7f261a 100644 --- a/Demos/Device/ClassDriver/AudioInput/Descriptors.h +++ b/Demos/Device/ClassDriver/AudioInput/Descriptors.h @@ -41,6 +41,8 @@ #include <avr/pgmspace.h> + #include "Config/AppConfig.h" + /* Macros: */ /** Endpoint address of the Audio isochronous streaming data IN endpoint. */ #define AUDIO_STREAM_EPADDR (ENDPOINT_DIR_IN | 1) diff --git a/Demos/Device/ClassDriver/AudioInput/makefile b/Demos/Device/ClassDriver/AudioInput/makefile index 61210c0f7..5724da5e6 100644 --- a/Demos/Device/ClassDriver/AudioInput/makefile +++ b/Demos/Device/ClassDriver/AudioInput/makefile @@ -120,14 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" - -LUFA_OPTS += -D MICROPHONE_BIASED_TO_HALF_RAIL -LUFA_OPTS += -D USE_TEST_TONE +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -172,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/AudioOutput/AudioOutput.h b/Demos/Device/ClassDriver/AudioOutput/AudioOutput.h index 9c6a0fb25..19ba276f3 100644 --- a/Demos/Device/ClassDriver/AudioOutput/AudioOutput.h +++ b/Demos/Device/ClassDriver/AudioOutput/AudioOutput.h @@ -44,8 +44,8 @@ #include <stdlib.h> #include "Descriptors.h" + #include "Config/AppConfig.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/USB/USB.h> diff --git a/Demos/Device/ClassDriver/AudioOutput/AudioOutput.txt b/Demos/Device/ClassDriver/AudioOutput/AudioOutput.txt index fbb654366..76445e0e2 100644 --- a/Demos/Device/ClassDriver/AudioOutput/AudioOutput.txt +++ b/Demos/Device/ClassDriver/AudioOutput/AudioOutput.txt @@ -73,17 +73,17 @@ * </tr> * <tr> * <td>AUDIO_OUT_STEREO</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, this outputs the audio samples in stereo to the timer output pins of the microcontroller.</td> * </tr> * <tr> * <td>AUDIO_OUT_MONO</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, this outputs the audio samples in mono to the timer output pin of the microcontroller.</td> * </tr> * <tr> * <td>AUDIO_OUT_PORTC</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, this outputs the audio samples in mono to port C of the microcontroller, for connection to an * external DAC.</td> * </tr> diff --git a/Demos/Device/ClassDriver/AudioOutput/Config/AppConfig.h b/Demos/Device/ClassDriver/AudioOutput/Config/AppConfig.h new file mode 100644 index 000000000..8524166c8 --- /dev/null +++ b/Demos/Device/ClassDriver/AudioOutput/Config/AppConfig.h @@ -0,0 +1,50 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief Application Configuration Header File + * + * This is a header file which is be used to configure some of + * the application's compile time options, as an alternative to + * specifying the compile time constants supplied through a + * makefile or build system. + * + * For information on what each token does, refer to the + * \ref Sec_Options section of the application documentation. + */ + +#ifndef _APP_CONFIG_H_ +#define _APP_CONFIG_H_ + + #define AUDIO_OUT_STEREO +// #define AUDIO_OUT_MONO +// #define AUDIO_OUT_PORTC + +#endif
\ No newline at end of file diff --git a/Demos/Device/ClassDriver/AudioOutput/Config/LUFAConfig.h b/Demos/Device/ClassDriver/AudioOutput/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/AudioOutput/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/AudioOutput/Descriptors.h b/Demos/Device/ClassDriver/AudioOutput/Descriptors.h index d5c8a2b84..4b294b805 100644 --- a/Demos/Device/ClassDriver/AudioOutput/Descriptors.h +++ b/Demos/Device/ClassDriver/AudioOutput/Descriptors.h @@ -41,6 +41,8 @@ #include <avr/pgmspace.h> + #include "Config/AppConfig.h" + /* Macros: */ /** Endpoint address of the Audio isochronous streaming data OUT endpoint. */ #define AUDIO_STREAM_EPADDR (ENDPOINT_DIR_OUT | 1) diff --git a/Demos/Device/ClassDriver/AudioOutput/makefile b/Demos/Device/ClassDriver/AudioOutput/makefile index e4757ddbb..88074f605 100644 --- a/Demos/Device/ClassDriver/AudioOutput/makefile +++ b/Demos/Device/ClassDriver/AudioOutput/makefile @@ -120,15 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" - -LUFA_OPTS += -D AUDIO_OUT_STEREO -#LUFA_OPTS += -D AUDIO_OUT_MONO -#LUFA_OPTS += -D AUDIO_OUT_PORTC +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -173,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/DualVirtualSerial/Config/LUFAConfig.h b/Demos/Device/ClassDriver/DualVirtualSerial/Config/LUFAConfig.h new file mode 100644 index 000000000..f91ef1895 --- /dev/null +++ b/Demos/Device/ClassDriver/DualVirtualSerial/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE + #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/DualVirtualSerial/Descriptors.c b/Demos/Device/ClassDriver/DualVirtualSerial/Descriptors.c index 1a4860ad3..a183b7fcb 100644 --- a/Demos/Device/ClassDriver/DualVirtualSerial/Descriptors.c +++ b/Demos/Device/ClassDriver/DualVirtualSerial/Descriptors.c @@ -37,17 +37,6 @@ #include "Descriptors.h" -/* On some devices, there is a factory set internal serial number which can be automatically sent to the host as - * the device's serial number when the Device Descriptor's .SerialNumStrIndex entry is set to USE_INTERNAL_SERIAL. - * This allows the host to track a device across insertions on different ports, allowing them to retain allocated - * resources like COM port numbers and drivers. On demos using this feature, give a warning on unsupported devices - * so that the user can supply their own serial number descriptor instead or remove the USE_INTERNAL_SERIAL value - * from the Device Descriptor (forcing the host to generate a serial number for each device from the VID, PID and - * port location). - */ -#if (USE_INTERNAL_SERIAL == NO_DESCRIPTOR) - #warning USE_INTERNAL_SERIAL is not available on this AVR - please manually construct a device serial descriptor. -#endif /** Device descriptor structure. This descriptor, located in FLASH memory, describes the overall * device characteristics, including the supported USB version, control endpoint size and the diff --git a/Demos/Device/ClassDriver/DualVirtualSerial/DualVirtualSerial.h b/Demos/Device/ClassDriver/DualVirtualSerial/DualVirtualSerial.h index 320f7dc36..e29fdee3e 100644 --- a/Demos/Device/ClassDriver/DualVirtualSerial/DualVirtualSerial.h +++ b/Demos/Device/ClassDriver/DualVirtualSerial/DualVirtualSerial.h @@ -45,7 +45,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/USB/USB.h> diff --git a/Demos/Device/ClassDriver/DualVirtualSerial/makefile b/Demos/Device/ClassDriver/DualVirtualSerial/makefile index 2065cca1e..064bf1289 100644 --- a/Demos/Device/ClassDriver/DualVirtualSerial/makefile +++ b/Demos/Device/ClassDriver/DualVirtualSerial/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/GenericHID/Config/AppConfig.h b/Demos/Device/ClassDriver/GenericHID/Config/AppConfig.h new file mode 100644 index 000000000..fccd16e3b --- /dev/null +++ b/Demos/Device/ClassDriver/GenericHID/Config/AppConfig.h @@ -0,0 +1,48 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief Application Configuration Header File + * + * This is a header file which is be used to configure some of + * the application's compile time options, as an alternative to + * specifying the compile time constants supplied through a + * makefile or build system. + * + * For information on what each token does, refer to the + * \ref Sec_Options section of the application documentation. + */ + +#ifndef _APP_CONFIG_H_ +#define _APP_CONFIG_H_ + + #define GENERIC_REPORT_SIZE 8 + +#endif
\ No newline at end of file diff --git a/Demos/Device/ClassDriver/GenericHID/Config/LUFAConfig.h b/Demos/Device/ClassDriver/GenericHID/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/GenericHID/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/GenericHID/Descriptors.h b/Demos/Device/ClassDriver/GenericHID/Descriptors.h index 0b9ec8f71..5e2740478 100644 --- a/Demos/Device/ClassDriver/GenericHID/Descriptors.h +++ b/Demos/Device/ClassDriver/GenericHID/Descriptors.h @@ -40,6 +40,8 @@ #include <avr/pgmspace.h> #include <LUFA/Drivers/USB/USB.h> + + #include "Config/AppConfig.h" /* Type Defines: */ /** Type define for the device configuration descriptor structure. This must be defined in the @@ -63,9 +65,6 @@ /** Size in bytes of the Generic HID reporting endpoint. */ #define GENERIC_EPSIZE 8 - /** Size in bytes of the Generic HID reports (including report ID byte). */ - #define GENERIC_REPORT_SIZE 8 - /* Function Prototypes: */ uint16_t CALLBACK_USB_GetDescriptor(const uint16_t wValue, const uint8_t wIndex, diff --git a/Demos/Device/ClassDriver/GenericHID/GenericHID.h b/Demos/Device/ClassDriver/GenericHID/GenericHID.h index ed3bb535c..4c4e33b2a 100644 --- a/Demos/Device/ClassDriver/GenericHID/GenericHID.h +++ b/Demos/Device/ClassDriver/GenericHID/GenericHID.h @@ -44,8 +44,8 @@ #include <string.h> #include "Descriptors.h" - - #include <LUFA/Version.h> + #include "Config/AppConfig.h" + #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/USB/USB.h> diff --git a/Demos/Device/ClassDriver/GenericHID/GenericHID.txt b/Demos/Device/ClassDriver/GenericHID/GenericHID.txt index 483675372..3d72345f3 100644 --- a/Demos/Device/ClassDriver/GenericHID/GenericHID.txt +++ b/Demos/Device/ClassDriver/GenericHID/GenericHID.txt @@ -67,9 +67,9 @@ * </tr> * <tr> * <td>GENERIC_REPORT_SIZE</td> - * <td>Descriptors.h</td> - * <td>This token defines the size of the device reports, both sent and received. The value must be an - * integer ranging from 1 to 255.</td> + * <td>AppConfig.h</td> + * <td>This token defines the size of the device reports, both sent and received (including report ID byte). The value + * must be an integer ranging from 1 to 255.</td> * </tr> * </table> */ diff --git a/Demos/Device/ClassDriver/GenericHID/makefile b/Demos/Device/ClassDriver/GenericHID/makefile index 21d3dcf2c..5ef95e060 100644 --- a/Demos/Device/ClassDriver/GenericHID/makefile +++ b/Demos/Device/ClassDriver/GenericHID/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/Joystick/Config/LUFAConfig.h b/Demos/Device/ClassDriver/Joystick/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/Joystick/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/Joystick/Joystick.h b/Demos/Device/ClassDriver/Joystick/Joystick.h index 4bc505654..8c51ae62b 100644 --- a/Demos/Device/ClassDriver/Joystick/Joystick.h +++ b/Demos/Device/ClassDriver/Joystick/Joystick.h @@ -45,7 +45,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Buttons.h> diff --git a/Demos/Device/ClassDriver/Joystick/makefile b/Demos/Device/ClassDriver/Joystick/makefile index 11eb5f77a..c970747a0 100644 --- a/Demos/Device/ClassDriver/Joystick/makefile +++ b/Demos/Device/ClassDriver/Joystick/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/Keyboard/Config/LUFAConfig.h b/Demos/Device/ClassDriver/Keyboard/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/Keyboard/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/Keyboard/Keyboard.h b/Demos/Device/ClassDriver/Keyboard/Keyboard.h index f79955121..ed6600a32 100644 --- a/Demos/Device/ClassDriver/Keyboard/Keyboard.h +++ b/Demos/Device/ClassDriver/Keyboard/Keyboard.h @@ -46,7 +46,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Buttons.h> diff --git a/Demos/Device/ClassDriver/Keyboard/makefile b/Demos/Device/ClassDriver/Keyboard/makefile index 6c82c4e1b..8b07bb520 100644 --- a/Demos/Device/ClassDriver/Keyboard/makefile +++ b/Demos/Device/ClassDriver/Keyboard/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/KeyboardMouse/Config/LUFAConfig.h b/Demos/Device/ClassDriver/KeyboardMouse/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/KeyboardMouse/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/KeyboardMouse/KeyboardMouse.h b/Demos/Device/ClassDriver/KeyboardMouse/KeyboardMouse.h index 14db865c8..d86a4338b 100644 --- a/Demos/Device/ClassDriver/KeyboardMouse/KeyboardMouse.h +++ b/Demos/Device/ClassDriver/KeyboardMouse/KeyboardMouse.h @@ -41,7 +41,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Buttons.h> diff --git a/Demos/Device/ClassDriver/KeyboardMouse/makefile b/Demos/Device/ClassDriver/KeyboardMouse/makefile index d7c64118f..7d4fc9537 100644 --- a/Demos/Device/ClassDriver/KeyboardMouse/makefile +++ b/Demos/Device/ClassDriver/KeyboardMouse/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/KeyboardMouseMultiReport/Config/LUFAConfig.h b/Demos/Device/ClassDriver/KeyboardMouseMultiReport/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/KeyboardMouseMultiReport/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/KeyboardMouseMultiReport/KeyboardMouseMultiReport.h b/Demos/Device/ClassDriver/KeyboardMouseMultiReport/KeyboardMouseMultiReport.h index 14db865c8..d86a4338b 100644 --- a/Demos/Device/ClassDriver/KeyboardMouseMultiReport/KeyboardMouseMultiReport.h +++ b/Demos/Device/ClassDriver/KeyboardMouseMultiReport/KeyboardMouseMultiReport.h @@ -41,7 +41,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Buttons.h> diff --git a/Demos/Device/ClassDriver/KeyboardMouseMultiReport/makefile b/Demos/Device/ClassDriver/KeyboardMouseMultiReport/makefile index 084a7143e..2909880e4 100644 --- a/Demos/Device/ClassDriver/KeyboardMouseMultiReport/makefile +++ b/Demos/Device/ClassDriver/KeyboardMouseMultiReport/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/MIDI/Config/LUFAConfig.h b/Demos/Device/ClassDriver/MIDI/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/MIDI/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/MIDI/MIDI.h b/Demos/Device/ClassDriver/MIDI/MIDI.h index b4d782726..fe49e89fe 100644 --- a/Demos/Device/ClassDriver/MIDI/MIDI.h +++ b/Demos/Device/ClassDriver/MIDI/MIDI.h @@ -46,7 +46,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/Board/Buttons.h> diff --git a/Demos/Device/ClassDriver/MIDI/makefile b/Demos/Device/ClassDriver/MIDI/makefile index 431e25fdd..e5b0e624a 100644 --- a/Demos/Device/ClassDriver/MIDI/makefile +++ b/Demos/Device/ClassDriver/MIDI/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/MassStorage/Config/AppConfig.h b/Demos/Device/ClassDriver/MassStorage/Config/AppConfig.h new file mode 100644 index 000000000..2582279ea --- /dev/null +++ b/Demos/Device/ClassDriver/MassStorage/Config/AppConfig.h @@ -0,0 +1,50 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief Application Configuration Header File + * + * This is a header file which is be used to configure some of + * the application's compile time options, as an alternative to + * specifying the compile time constants supplied through a + * makefile or build system. + * + * For information on what each token does, refer to the + * \ref Sec_Options section of the application documentation. + */ + +#ifndef _APP_CONFIG_H_ +#define _APP_CONFIG_H_ + + #define TOTAL_LUNS 1 + + #define DISK_READ_ONLY false + +#endif
\ No newline at end of file diff --git a/Demos/Device/ClassDriver/MassStorage/Config/LUFAConfig.h b/Demos/Device/ClassDriver/MassStorage/Config/LUFAConfig.h new file mode 100644 index 000000000..f91ef1895 --- /dev/null +++ b/Demos/Device/ClassDriver/MassStorage/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE + #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/MassStorage/Descriptors.c b/Demos/Device/ClassDriver/MassStorage/Descriptors.c index 5c62f7fb1..36774e804 100644 --- a/Demos/Device/ClassDriver/MassStorage/Descriptors.c +++ b/Demos/Device/ClassDriver/MassStorage/Descriptors.c @@ -37,17 +37,6 @@ #include "Descriptors.h" -/* On some devices, there is a factory set internal serial number which can be automatically sent to the host as - * the device's serial number when the Device Descriptor's .SerialNumStrIndex entry is set to USE_INTERNAL_SERIAL. - * This allows the host to track a device across insertions on different ports, allowing them to retain allocated - * resources like COM port numbers and drivers. On demos using this feature, give a warning on unsupported devices - * so that the user can supply their own serial number descriptor instead or remove the USE_INTERNAL_SERIAL value - * from the Device Descriptor (forcing the host to generate a serial number for each device from the VID, PID and - * port location). - */ -#if (USE_INTERNAL_SERIAL == NO_DESCRIPTOR) - #warning USE_INTERNAL_SERIAL is not available on this AVR - please manually construct a device serial descriptor. -#endif /** Device descriptor structure. This descriptor, located in FLASH memory, describes the overall * device characteristics, including the supported USB version, control endpoint size and the diff --git a/Demos/Device/ClassDriver/MassStorage/Descriptors.h b/Demos/Device/ClassDriver/MassStorage/Descriptors.h index 84879e822..643747b36 100644 --- a/Demos/Device/ClassDriver/MassStorage/Descriptors.h +++ b/Demos/Device/ClassDriver/MassStorage/Descriptors.h @@ -41,6 +41,8 @@ #include <LUFA/Drivers/USB/USB.h> + #include "Config/AppConfig.h" + /* Macros: */ /** Endpoint address of the Mass Storage device-to-host data IN endpoint. */ #define MASS_STORAGE_IN_EPADDR (ENDPOINT_DIR_IN | 3) diff --git a/Demos/Device/ClassDriver/MassStorage/Lib/DataflashManager.h b/Demos/Device/ClassDriver/MassStorage/Lib/DataflashManager.h index 18606eaf1..65c4f60b0 100644 --- a/Demos/Device/ClassDriver/MassStorage/Lib/DataflashManager.h +++ b/Demos/Device/ClassDriver/MassStorage/Lib/DataflashManager.h @@ -41,7 +41,8 @@ #include "../MassStorage.h" #include "../Descriptors.h" - + #include "Config/AppConfig.h" + #include <LUFA/Common/Common.h> #include <LUFA/Drivers/USB/USB.h> #include <LUFA/Drivers/Board/Dataflash.h> @@ -65,6 +66,9 @@ */ #define VIRTUAL_MEMORY_BLOCKS (VIRTUAL_MEMORY_BYTES / VIRTUAL_MEMORY_BLOCK_SIZE) + /** Blocks in each LUN, calculated from the total capacity divided by the total number of Logical Units in the device. */ + #define LUN_MEDIA_BLOCKS (VIRTUAL_MEMORY_BLOCKS / TOTAL_LUNS) + /* Function Prototypes: */ void DataflashManager_WriteBlocks(USB_ClassInfo_MS_Device_t* const MSInterfaceInfo, const uint32_t BlockAddress, diff --git a/Demos/Device/ClassDriver/MassStorage/Lib/SCSI.h b/Demos/Device/ClassDriver/MassStorage/Lib/SCSI.h index d44662382..610d3672c 100644 --- a/Demos/Device/ClassDriver/MassStorage/Lib/SCSI.h +++ b/Demos/Device/ClassDriver/MassStorage/Lib/SCSI.h @@ -45,7 +45,8 @@ #include "../MassStorage.h" #include "../Descriptors.h" #include "DataflashManager.h" - + #include "Config/AppConfig.h" + /* Macros: */ /** Macro to set the current SCSI sense data to the given key, additional sense code and additional sense qualifier. This * is for convenience, as it allows for all three sense values (returned upon request to the host to give information about diff --git a/Demos/Device/ClassDriver/MassStorage/MassStorage.h b/Demos/Device/ClassDriver/MassStorage/MassStorage.h index da01449d0..957a880d9 100644 --- a/Demos/Device/ClassDriver/MassStorage/MassStorage.h +++ b/Demos/Device/ClassDriver/MassStorage/MassStorage.h @@ -47,8 +47,8 @@ #include "Lib/SCSI.h" #include "Lib/DataflashManager.h" + #include "Config/AppConfig.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/USB/USB.h> @@ -68,15 +68,6 @@ /** LED mask for the library LED driver, to indicate that the USB interface is busy. */ #define LEDMASK_USB_BUSY LEDS_LED2 - /** Total number of logical drives within the device - must be non-zero. */ - #define TOTAL_LUNS 1 - - /** Blocks in each LUN, calculated from the total capacity divided by the total number of Logical Units in the device. */ - #define LUN_MEDIA_BLOCKS (VIRTUAL_MEMORY_BLOCKS / TOTAL_LUNS) - - /** Indicates if the disk is write protected or not. */ - #define DISK_READ_ONLY false - /* Function Prototypes: */ void SetupHardware(void); diff --git a/Demos/Device/ClassDriver/MassStorage/MassStorage.txt b/Demos/Device/ClassDriver/MassStorage/MassStorage.txt index 14fdd4abe..5bf7c5570 100644 --- a/Demos/Device/ClassDriver/MassStorage/MassStorage.txt +++ b/Demos/Device/ClassDriver/MassStorage/MassStorage.txt @@ -83,10 +83,15 @@ * </tr> * <tr> * <td>TOTAL_LUNS</td> - * <td>MassStorage.h</td> + * <td>AppConfig.h</td> * <td>Total number of Logical Units (drives) in the device. The total device capacity is shared equally between each drive - * this can be set to any positive non-zero amount.</td> * </tr> + * <tr> + * <td>DISK_READ_ONLY</td> + * <td>AppConfig.h</td> + * <td>Configuration define, indicating if the disk should be write protected or not.</td> + * </tr> * </table> */ diff --git a/Demos/Device/ClassDriver/MassStorage/makefile b/Demos/Device/ClassDriver/MassStorage/makefile index 4bbaded5e..0ee461967 100644 --- a/Demos/Device/ClassDriver/MassStorage/makefile +++ b/Demos/Device/ClassDriver/MassStorage/makefile @@ -172,7 +172,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/Config/AppConfig.h b/Demos/Device/ClassDriver/MassStorageKeyboard/Config/AppConfig.h new file mode 100644 index 000000000..2582279ea --- /dev/null +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/Config/AppConfig.h @@ -0,0 +1,50 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief Application Configuration Header File + * + * This is a header file which is be used to configure some of + * the application's compile time options, as an alternative to + * specifying the compile time constants supplied through a + * makefile or build system. + * + * For information on what each token does, refer to the + * \ref Sec_Options section of the application documentation. + */ + +#ifndef _APP_CONFIG_H_ +#define _APP_CONFIG_H_ + + #define TOTAL_LUNS 1 + + #define DISK_READ_ONLY false + +#endif
\ No newline at end of file diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/Config/LUFAConfig.h b/Demos/Device/ClassDriver/MassStorageKeyboard/Config/LUFAConfig.h new file mode 100644 index 000000000..f91ef1895 --- /dev/null +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE + #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/Descriptors.c b/Demos/Device/ClassDriver/MassStorageKeyboard/Descriptors.c index 6818a7acb..c5d92015e 100644 --- a/Demos/Device/ClassDriver/MassStorageKeyboard/Descriptors.c +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/Descriptors.c @@ -38,17 +38,6 @@ #include "Descriptors.h" -/* On some devices, there is a factory set internal serial number which can be automatically sent to the host as - * the device's serial number when the Device Descriptor's .SerialNumStrIndex entry is set to USE_INTERNAL_SERIAL. - * This allows the host to track a device across insertions on different ports, allowing them to retain allocated - * resources like COM port numbers and drivers. On demos using this feature, give a warning on unsupported devices - * so that the user can supply their own serial number descriptor instead or remove the USE_INTERNAL_SERIAL value - * from the Device Descriptor (forcing the host to generate a serial number for each device from the VID, PID and - * port location). - */ -#if (USE_INTERNAL_SERIAL == NO_DESCRIPTOR) - #warning USE_INTERNAL_SERIAL is not available on this AVR - please manually construct a device serial descriptor. -#endif /** HID class report descriptor. This is a special descriptor constructed with values from the * USBIF HID class specification to describe the reports and capabilities of the HID device. This diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/Descriptors.h b/Demos/Device/ClassDriver/MassStorageKeyboard/Descriptors.h index fb1a3794f..f79cd2ee6 100644 --- a/Demos/Device/ClassDriver/MassStorageKeyboard/Descriptors.h +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/Descriptors.h @@ -42,6 +42,8 @@ #include <LUFA/Drivers/USB/USB.h> + #include "Config/AppConfig.h" + /* Macros: */ /** Endpoint address of the Keyboard HID reporting IN endpoint. */ #define KEYBOARD_EPADDR (ENDPOINT_DIR_IN | 1) diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/Lib/DataflashManager.h b/Demos/Device/ClassDriver/MassStorageKeyboard/Lib/DataflashManager.h index f7552dc4a..68356b2c5 100644 --- a/Demos/Device/ClassDriver/MassStorageKeyboard/Lib/DataflashManager.h +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/Lib/DataflashManager.h @@ -41,7 +41,8 @@ #include "../MassStorageKeyboard.h" #include "../Descriptors.h" - + #include "Config/AppConfig.h" + #include <LUFA/Common/Common.h> #include <LUFA/Drivers/USB/USB.h> #include <LUFA/Drivers/Board/Dataflash.h> @@ -63,6 +64,9 @@ /** Total number of blocks of the virtual memory for reporting to the host as the device's total capacity. */ #define VIRTUAL_MEMORY_BLOCKS (VIRTUAL_MEMORY_BYTES / VIRTUAL_MEMORY_BLOCK_SIZE) + /** Blocks in each LUN, calculated from the total capacity divided by the total number of Logical Units in the device. */ + #define LUN_MEDIA_BLOCKS (VIRTUAL_MEMORY_BLOCKS / TOTAL_LUNS) + /* Function Prototypes: */ void DataflashManager_WriteBlocks(USB_ClassInfo_MS_Device_t* const MSInterfaceInfo, const uint32_t BlockAddress, diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/Lib/SCSI.h b/Demos/Device/ClassDriver/MassStorageKeyboard/Lib/SCSI.h index 5c3d3bf97..55ead069c 100644 --- a/Demos/Device/ClassDriver/MassStorageKeyboard/Lib/SCSI.h +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/Lib/SCSI.h @@ -45,7 +45,8 @@ #include "../MassStorageKeyboard.h" #include "../Descriptors.h" #include "DataflashManager.h" - + #include "Config/AppConfig.h" + /* Macros: */ /** Macro to set the current SCSI sense data to the given key, additional sense code and additional sense qualifier. This * is for convenience, as it allows for all three sense values (returned upon request to the host to give information about diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/MassStorageKeyboard.h b/Demos/Device/ClassDriver/MassStorageKeyboard/MassStorageKeyboard.h index 8f8fa0029..6c0f1d9e1 100644 --- a/Demos/Device/ClassDriver/MassStorageKeyboard/MassStorageKeyboard.h +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/MassStorageKeyboard.h @@ -50,8 +50,8 @@ #include "Lib/SCSI.h" #include "Lib/DataflashManager.h" + #include "Config/AppConfig.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Buttons.h> @@ -73,15 +73,6 @@ /** LED mask for the library LED driver, to indicate that the USB interface is busy. */ #define LEDMASK_USB_BUSY LEDS_LED2 - /** Total number of logical drives within the device - must be non-zero. */ - #define TOTAL_LUNS 1 - - /** Blocks in each LUN, calculated from the total capacity divided by the total number of Logical Units in the device. */ - #define LUN_MEDIA_BLOCKS (VIRTUAL_MEMORY_BLOCKS / TOTAL_LUNS) - - /** Indicates if the disk is write protected or not. */ - #define DISK_READ_ONLY false - /* Function Prototypes: */ void SetupHardware(void); diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/MassStorageKeyboard.txt b/Demos/Device/ClassDriver/MassStorageKeyboard/MassStorageKeyboard.txt index 8c1355c5d..7cdb47279 100644 --- a/Demos/Device/ClassDriver/MassStorageKeyboard/MassStorageKeyboard.txt +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/MassStorageKeyboard.txt @@ -84,10 +84,14 @@ * </tr> * <tr> * <td>TOTAL_LUNS</td> - * <td>MassStorage.h</td> + * <td>AppConfig.h</td> * <td>Total number of Logical Units (drives) in the device. The total device capacity is shared equally between each drive - * this can be set to any positive non-zero amount.</td> * </tr> - * </table> + * <tr> + * <td>DISK_READ_ONLY</td> + * <td>AppConfig.h</td> + * <td>Configuration define, indicating if the disk should be write protected or not.</td> + * </tr> */ diff --git a/Demos/Device/ClassDriver/MassStorageKeyboard/makefile b/Demos/Device/ClassDriver/MassStorageKeyboard/makefile index 101f359a0..a504d0c63 100644 --- a/Demos/Device/ClassDriver/MassStorageKeyboard/makefile +++ b/Demos/Device/ClassDriver/MassStorageKeyboard/makefile @@ -120,12 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" -LUFA_OPTS += -D INTERRUPT_CONTROL_ENDPOINT +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -172,7 +167,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/Mouse/Config/LUFAConfig.h b/Demos/Device/ClassDriver/Mouse/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/Mouse/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/Mouse/Mouse.h b/Demos/Device/ClassDriver/Mouse/Mouse.h index 73f9742a8..4d6c27e51 100644 --- a/Demos/Device/ClassDriver/Mouse/Mouse.h +++ b/Demos/Device/ClassDriver/Mouse/Mouse.h @@ -47,7 +47,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Buttons.h> diff --git a/Demos/Device/ClassDriver/Mouse/makefile b/Demos/Device/ClassDriver/Mouse/makefile index 344b0b591..7c7493d1a 100644 --- a/Demos/Device/ClassDriver/Mouse/makefile +++ b/Demos/Device/ClassDriver/Mouse/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/RNDISEthernet/Config/AppConfig.h b/Demos/Device/ClassDriver/RNDISEthernet/Config/AppConfig.h new file mode 100644 index 000000000..3b1ca5366 --- /dev/null +++ b/Demos/Device/ClassDriver/RNDISEthernet/Config/AppConfig.h @@ -0,0 +1,60 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief Application Configuration Header File + * + * This is a header file which is be used to configure some of + * the application's compile time options, as an alternative to + * specifying the compile time constants supplied through a + * makefile or build system. + * + * For information on what each token does, refer to the + * \ref Sec_Options section of the application documentation. + */ + +#ifndef _APP_CONFIG_H_ +#define _APP_CONFIG_H_ + + #define CLIENT_IP_ADDRESS { 10, 0, 0, 1} + #define SERVER_IP_ADDRESS { 10, 0, 0, 2} + + #define ADAPTER_MAC_ADDRESS {0x02, 0x00, 0x02, 0x00, 0x02, 0x00} + #define SERVER_MAC_ADDRESS {0x00, 0x01, 0x00, 0x01, 0x00, 0x01} + + #define NO_DECODE_ETHERNET + #define NO_DECODE_ARP + #define NO_DECODE_IP + #define NO_DECODE_ICMP + #define NO_DECODE_TCP + #define NO_DECODE_UDP + #define NO_DECODE_DHCP + +#endif diff --git a/Demos/Device/ClassDriver/RNDISEthernet/Config/LUFAConfig.h b/Demos/Device/ClassDriver/RNDISEthernet/Config/LUFAConfig.h new file mode 100644 index 000000000..a1d748267 --- /dev/null +++ b/Demos/Device/ClassDriver/RNDISEthernet/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE +// #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/RNDISEthernet/Descriptors.h b/Demos/Device/ClassDriver/RNDISEthernet/Descriptors.h index 6301b83aa..9baae86e7 100644 --- a/Demos/Device/ClassDriver/RNDISEthernet/Descriptors.h +++ b/Demos/Device/ClassDriver/RNDISEthernet/Descriptors.h @@ -41,6 +41,8 @@ #include <avr/pgmspace.h> + #include "Config/AppConfig.h" + /* Macros: */ /** Endpoint address of the CDC device-to-host notification IN endpoint. */ #define CDC_NOTIFICATION_EPADDR (ENDPOINT_DIR_IN | 3) diff --git a/Demos/Device/ClassDriver/RNDISEthernet/Lib/Ethernet.h b/Demos/Device/ClassDriver/RNDISEthernet/Lib/Ethernet.h index aeebd0ac8..4e91bc268 100644 --- a/Demos/Device/ClassDriver/RNDISEthernet/Lib/Ethernet.h +++ b/Demos/Device/ClassDriver/RNDISEthernet/Lib/Ethernet.h @@ -42,6 +42,8 @@ #include <LUFA/Drivers/USB/USB.h> + #include "Config/AppConfig.h" + #include "EthernetProtocols.h" #include "ProtocolDecoders.h" #include "ICMP.h" @@ -52,12 +54,6 @@ #include "IP.h" /* Macros: */ - /** Physical MAC address of the USB RNDIS network adapter. */ - #define ADAPTER_MAC_ADDRESS {0x02, 0x00, 0x02, 0x00, 0x02, 0x00} - - /** Physical MAC address of the virtual server on the network. */ - #define SERVER_MAC_ADDRESS {0x00, 0x01, 0x00, 0x01, 0x00, 0x01} - /** Physical MAC address of the network broadcast address. */ #define BROADCAST_MAC_ADDRESS {0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF} diff --git a/Demos/Device/ClassDriver/RNDISEthernet/Lib/IP.h b/Demos/Device/ClassDriver/RNDISEthernet/Lib/IP.h index 2ed173f57..d1a709fbd 100644 --- a/Demos/Device/ClassDriver/RNDISEthernet/Lib/IP.h +++ b/Demos/Device/ClassDriver/RNDISEthernet/Lib/IP.h @@ -43,14 +43,9 @@ #include "EthernetProtocols.h" #include "Ethernet.h" #include "ProtocolDecoders.h" + #include "Config/AppConfig.h" /* Macros: */ - /** Protocol IP address of the host (client) machine, once assigned by DHCP. */ - #define CLIENT_IP_ADDRESS { 10, 0, 0, 1} - - /** Protocol IP address of the virtual server machine. */ - #define SERVER_IP_ADDRESS { 10, 0, 0, 2} - /** Protocol IP address of the broadcast address. */ #define BROADCAST_IP_ADDRESS {0xFF, 0xFF, 0xFF, 0xFF} diff --git a/Demos/Device/ClassDriver/RNDISEthernet/Lib/ProtocolDecoders.h b/Demos/Device/ClassDriver/RNDISEthernet/Lib/ProtocolDecoders.h index 2807b6056..bb640928d 100644 --- a/Demos/Device/ClassDriver/RNDISEthernet/Lib/ProtocolDecoders.h +++ b/Demos/Device/ClassDriver/RNDISEthernet/Lib/ProtocolDecoders.h @@ -45,6 +45,7 @@ #include "EthernetProtocols.h" #include "Ethernet.h" + #include "Config/AppConfig.h" /* Function Prototypes: */ void DecodeEthernetFrameHeader(void* InDataStart); diff --git a/Demos/Device/ClassDriver/RNDISEthernet/RNDISEthernet.h b/Demos/Device/ClassDriver/RNDISEthernet/RNDISEthernet.h index 6ff089647..e70fd5d63 100644 --- a/Demos/Device/ClassDriver/RNDISEthernet/RNDISEthernet.h +++ b/Demos/Device/ClassDriver/RNDISEthernet/RNDISEthernet.h @@ -49,8 +49,8 @@ #include "Lib/TCP.h" #include "Lib/ARP.h" #include "Lib/Webserver.h" - - #include <LUFA/Version.h> + #include "Config/AppConfig.h" + #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Peripheral/Serial.h> #include <LUFA/Drivers/USB/USB.h> diff --git a/Demos/Device/ClassDriver/RNDISEthernet/RNDISEthernet.txt b/Demos/Device/ClassDriver/RNDISEthernet/RNDISEthernet.txt index 648fe40f1..ac72d4ae7 100644 --- a/Demos/Device/ClassDriver/RNDISEthernet/RNDISEthernet.txt +++ b/Demos/Device/ClassDriver/RNDISEthernet/RNDISEthernet.txt @@ -84,38 +84,58 @@ * <td><b>Description:</b></td> * </tr> * <tr> + * <td>CLIENT_IP_ADDRESS</td> + * <td>AppConfig.h</td> + * <td>Configures the IP address given to the client (PC) via the DHCP server.</td> + * </tr> + * <tr> + * <td>SERVER_IP_ADDRESS</td> + * <td>AppConfig.h</td> + * <td>Configures the IP address of the virtual server.</td> + * </tr> + * <tr> + * <td>ADAPTER_MAC_ADDRESS</td> + * <td>AppConfig.h</td> + * <td>Configures the MAC address of the RNDIS adapter on the host (PC) side.</td> + * </tr> + * <tr> + * <td>SERVER_MAC_ADDRESS</td> + * <td>AppConfig.h</td> + * <td>Configures the MAC address of the virtual server on the network.</td> + * </tr> + * <tr> * <td>NO_DECODE_ETHERNET</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, received Ethernet headers will not be decoded and printed to the device serial port.</td> * </tr> * <tr> * <td>NO_DECODE_ARP</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, received ARP headers will not be decoded and printed to the device serial port.</td> * </tr> * <tr> * <td>NO_DECODE_IP</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, received IP headers will not be decoded and printed to the device serial port.</td> * </tr> * <tr> * <td>NO_DECODE_ICMP</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, received ICMP headers will not be decoded and printed to the device serial port.</td> * </tr> * <tr> * <td>NO_DECODE_TCP</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, received TCP headers will not be decoded and printed to the device serial port.</td> * </tr> * <tr> * <td>NO_DECODE_UDP</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, received UDP headers will not be decoded and printed to the device serial port.</td> * </tr> * <tr> * <td>NO_DECODE_DHCP</td> - * <td>Makefile LUFA_OPTS</td> + * <td>AppConfig.h</td> * <td>When defined, received DHCP headers will not be decoded and printed to the device serial port.</td> * </tr> * </table> diff --git a/Demos/Device/ClassDriver/RNDISEthernet/makefile b/Demos/Device/ClassDriver/RNDISEthernet/makefile index 4b2642c4e..c53705609 100644 --- a/Demos/Device/ClassDriver/RNDISEthernet/makefile +++ b/Demos/Device/ClassDriver/RNDISEthernet/makefile @@ -120,19 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" - -LUFA_OPTS += -D NO_DECODE_ETHERNET -LUFA_OPTS += -D NO_DECODE_ARP -LUFA_OPTS += -D NO_DECODE_IP -LUFA_OPTS += -D NO_DECODE_ICMP -LUFA_OPTS += -D NO_DECODE_TCP -LUFA_OPTS += -D NO_DECODE_UDP -LUFA_OPTS += -D NO_DECODE_DHCP +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -187,7 +175,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/VirtualSerial/Config/LUFAConfig.h b/Demos/Device/ClassDriver/VirtualSerial/Config/LUFAConfig.h new file mode 100644 index 000000000..f91ef1895 --- /dev/null +++ b/Demos/Device/ClassDriver/VirtualSerial/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE + #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/VirtualSerial/Descriptors.c b/Demos/Device/ClassDriver/VirtualSerial/Descriptors.c index 9dcf4e4d4..0a11dcb79 100644 --- a/Demos/Device/ClassDriver/VirtualSerial/Descriptors.c +++ b/Demos/Device/ClassDriver/VirtualSerial/Descriptors.c @@ -37,17 +37,6 @@ #include "Descriptors.h" -/* On some devices, there is a factory set internal serial number which can be automatically sent to the host as - * the device's serial number when the Device Descriptor's .SerialNumStrIndex entry is set to USE_INTERNAL_SERIAL. - * This allows the host to track a device across insertions on different ports, allowing them to retain allocated - * resources like COM port numbers and drivers. On demos using this feature, give a warning on unsupported devices - * so that the user can supply their own serial number descriptor instead or remove the USE_INTERNAL_SERIAL value - * from the Device Descriptor (forcing the host to generate a serial number for each device from the VID, PID and - * port location). - */ -#if (USE_INTERNAL_SERIAL == NO_DESCRIPTOR) - #warning USE_INTERNAL_SERIAL is not available on this AVR - please manually construct a device serial descriptor. -#endif /** Device descriptor structure. This descriptor, located in FLASH memory, describes the overall * device characteristics, including the supported USB version, control endpoint size and the diff --git a/Demos/Device/ClassDriver/VirtualSerial/VirtualSerial.h b/Demos/Device/ClassDriver/VirtualSerial/VirtualSerial.h index ce7de149f..3baeafebd 100644 --- a/Demos/Device/ClassDriver/VirtualSerial/VirtualSerial.h +++ b/Demos/Device/ClassDriver/VirtualSerial/VirtualSerial.h @@ -46,7 +46,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/USB/USB.h> diff --git a/Demos/Device/ClassDriver/VirtualSerial/makefile b/Demos/Device/ClassDriver/VirtualSerial/makefile index fc6dc146d..e00235113 100644 --- a/Demos/Device/ClassDriver/VirtualSerial/makefile +++ b/Demos/Device/ClassDriver/VirtualSerial/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Config/AppConfig.h b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Config/AppConfig.h new file mode 100644 index 000000000..2582279ea --- /dev/null +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Config/AppConfig.h @@ -0,0 +1,50 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief Application Configuration Header File + * + * This is a header file which is be used to configure some of + * the application's compile time options, as an alternative to + * specifying the compile time constants supplied through a + * makefile or build system. + * + * For information on what each token does, refer to the + * \ref Sec_Options section of the application documentation. + */ + +#ifndef _APP_CONFIG_H_ +#define _APP_CONFIG_H_ + + #define TOTAL_LUNS 1 + + #define DISK_READ_ONLY false + +#endif
\ No newline at end of file diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Config/LUFAConfig.h b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Config/LUFAConfig.h new file mode 100644 index 000000000..f91ef1895 --- /dev/null +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE + #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Descriptors.c b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Descriptors.c index cfccac02b..607a2b02d 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Descriptors.c +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Descriptors.c @@ -37,17 +37,6 @@ #include "Descriptors.h" -/* On some devices, there is a factory set internal serial number which can be automatically sent to the host as - * the device's serial number when the Device Descriptor's .SerialNumStrIndex entry is set to USE_INTERNAL_SERIAL. - * This allows the host to track a device across insertions on different ports, allowing them to retain allocated - * resources like COM port numbers and drivers. On demos using this feature, give a warning on unsupported devices - * so that the user can supply their own serial number descriptor instead or remove the USE_INTERNAL_SERIAL value - * from the Device Descriptor (forcing the host to generate a serial number for each device from the VID, PID and - * port location). - */ -#if (USE_INTERNAL_SERIAL == NO_DESCRIPTOR) - #warning USE_INTERNAL_SERIAL is not available on this AVR - please manually construct a device serial descriptor. -#endif /** Device descriptor structure. This descriptor, located in FLASH memory, describes the overall * device characteristics, including the supported USB version, control endpoint size and the diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Descriptors.h b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Descriptors.h index 544a2b5c0..e2d856267 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Descriptors.h +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Descriptors.h @@ -41,6 +41,8 @@ #include <LUFA/Drivers/USB/USB.h> + #include "Config/AppConfig.h" + /* Macros: */ /** Endpoint address of the CDC device-to-host notification IN endpoint. */ #define CDC_NOTIFICATION_EPADDR (ENDPOINT_DIR_IN | 1) diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Lib/DataflashManager.h b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Lib/DataflashManager.h index 1d1238658..e9e2ef97f 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Lib/DataflashManager.h +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Lib/DataflashManager.h @@ -41,6 +41,7 @@ #include "../VirtualSerialMassStorage.h" #include "../Descriptors.h" + #include "Config/AppConfig.h" #include <LUFA/Common/Common.h> #include <LUFA/Drivers/USB/USB.h> @@ -65,6 +66,9 @@ */ #define VIRTUAL_MEMORY_BLOCKS (VIRTUAL_MEMORY_BYTES / VIRTUAL_MEMORY_BLOCK_SIZE) + /** Blocks in each LUN, calculated from the total capacity divided by the total number of Logical Units in the device. */ + #define LUN_MEDIA_BLOCKS (VIRTUAL_MEMORY_BLOCKS / TOTAL_LUNS) + /* Function Prototypes: */ void DataflashManager_WriteBlocks(USB_ClassInfo_MS_Device_t* const MSInterfaceInfo, const uint32_t BlockAddress, diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Lib/SCSI.h b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Lib/SCSI.h index 83d5646c4..01614cc1c 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMassStorage/Lib/SCSI.h +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/Lib/SCSI.h @@ -45,7 +45,8 @@ #include "../VirtualSerialMassStorage.h" #include "../Descriptors.h" #include "DataflashManager.h" - + #include "Config/AppConfig.h" + /* Macros: */ /** Macro to set the current SCSI sense data to the given key, additional sense code and additional sense qualifier. This * is for convenience, as it allows for all three sense values (returned upon request to the host to give information about diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/VirtualSerialMassStorage.h b/Demos/Device/ClassDriver/VirtualSerialMassStorage/VirtualSerialMassStorage.h index 486351b2f..3d17971d5 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMassStorage/VirtualSerialMassStorage.h +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/VirtualSerialMassStorage.h @@ -47,8 +47,8 @@ #include "Lib/SCSI.h" #include "Lib/DataflashManager.h" + #include "Config/AppConfig.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/USB/USB.h> @@ -69,15 +69,6 @@ /** LED mask for the library LED driver, to indicate that the USB interface is busy. */ #define LEDMASK_USB_BUSY LEDS_LED2 - /** Total number of logical drives within the device - must be non-zero. */ - #define TOTAL_LUNS 1 - - /** Blocks in each LUN, calculated from the total capacity divided by the total number of Logical Units in the device. */ - #define LUN_MEDIA_BLOCKS (VIRTUAL_MEMORY_BLOCKS / TOTAL_LUNS) - - /** Indicates if the disk is write protected or not. */ - #define DISK_READ_ONLY false - /* Function Prototypes: */ void SetupHardware(void); void CheckJoystickMovement(void); diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/VirtualSerialMassStorage.txt b/Demos/Device/ClassDriver/VirtualSerialMassStorage/VirtualSerialMassStorage.txt index b616ad72b..042244119 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMassStorage/VirtualSerialMassStorage.txt +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/VirtualSerialMassStorage.txt @@ -77,10 +77,14 @@ * </tr> * <tr> * <td>TOTAL_LUNS</td> - * <td>MassStorage.h</td> + * <td>AppConfig.h</td> * <td>Total number of Logical Units (drives) in the device. The total device capacity is shared equally between each drive - * this can be set to any positive non-zero amount.</td> * </tr> - * </table> + * <tr> + * <td>DISK_READ_ONLY</td> + * <td>AppConfig.h</td> + * <td>Configuration define, indicating if the disk should be write protected or not.</td> + * </tr> */ diff --git a/Demos/Device/ClassDriver/VirtualSerialMassStorage/makefile b/Demos/Device/ClassDriver/VirtualSerialMassStorage/makefile index cac2baf70..57b78a87e 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMassStorage/makefile +++ b/Demos/Device/ClassDriver/VirtualSerialMassStorage/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -171,7 +167,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. diff --git a/Demos/Device/ClassDriver/VirtualSerialMouse/Config/LUFAConfig.h b/Demos/Device/ClassDriver/VirtualSerialMouse/Config/LUFAConfig.h new file mode 100644 index 000000000..f91ef1895 --- /dev/null +++ b/Demos/Device/ClassDriver/VirtualSerialMouse/Config/LUFAConfig.h @@ -0,0 +1,93 @@ +/* + LUFA Library + Copyright (C) Dean Camera, 2012. + + dean [at] fourwalledcubicle [dot] com + www.lufa-lib.org +*/ + +/* + Copyright 2012 Dean Camera (dean [at] fourwalledcubicle [dot] com) + + Permission to use, copy, modify, distribute, and sell this + software and its documentation for any purpose is hereby granted + without fee, provided that the above copyright notice appear in + all copies and that both that the copyright notice and this + permission notice and warranty disclaimer appear in supporting + documentation, and that the name of the author not be used in + advertising or publicity pertaining to distribution of the + software without specific, written prior permission. + + The author disclaim all warranties with regard to this + software, including all implied warranties of merchantability + and fitness. In no event shall the author be liable for any + special, indirect or consequential damages or any damages + whatsoever resulting from loss of use, data or profits, whether + in an action of contract, negligence or other tortious action, + arising out of or in connection with the use or performance of + this software. +*/ + +/** \file + * \brief LUFA Library Configuration Header File + * + * This header file is used to configure LUFA's compile time options, + * as an alternative to the compile time constants supplied through + * a makefile. + * + * For information on what each token does, refer to the LUFA + * manual section "Summary of Compile Tokens". + */ + +#ifndef _LUFA_CONFIG_H_ +#define _LUFA_CONFIG_H_ + + #if (ARCH == ARCH_AVR8) + + /* Non-USB Related Configuration Tokens: */ +// #define DISABLE_TERMINAL_CODES + + /* USB Class Driver Related Tokens: */ +// #define HID_HOST_BOOT_PROTOCOL_ONLY +// #define HID_STATETABLE_STACK_DEPTH {Insert Value Here} +// #define HID_USAGE_STACK_DEPTH {Insert Value Here} +// #define HID_MAX_COLLECTIONS {Insert Value Here} +// #define HID_MAX_REPORTITEMS {Insert Value Here} +// #define HID_MAX_REPORT_IDS {Insert Value Here} +// #define NO_CLASS_DRIVER_AUTOFLUSH + + /* General USB Driver Related Tokens: */ +// #define ORDERED_EP_CONFIG + #define USE_STATIC_OPTIONS (USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL) + #define USB_DEVICE_ONLY +// #define USB_HOST_ONLY +// #define USB_STREAM_TIMEOUT_MS {Insert Value Here} +// #define NO_LIMITED_CONTROLLER_CONNECT +// #define NO_SOF_EVENTS + + /* USB Device Mode Driver Related Tokens: */ +// #define USE_RAM_DESCRIPTORS + #define USE_FLASH_DESCRIPTORS +// #define USE_EEPROM_DESCRIPTORS +// #define NO_INTERNAL_SERIAL + #define FIXED_CONTROL_ENDPOINT_SIZE 8 +// #define DEVICE_STATE_AS_GPIOR {Insert Value Here} + #define FIXED_NUM_CONFIGURATIONS 1 +// #define CONTROL_ONLY_DEVICE + #define INTERRUPT_CONTROL_ENDPOINT +// #define NO_DEVICE_REMOTE_WAKEUP +// #define NO_DEVICE_SELF_POWER + + /* USB Host Mode Driver Related Tokens: */ +// #define HOST_STATE_AS_GPIOR {Insert Value Here} +// #define USB_HOST_TIMEOUT_MS {Insert Value Here} +// #define HOST_DEVICE_SETTLE_DELAY_MS {Insert Value Here} +// #define NO_AUTO_VBUS_MANAGEMENT +// #define INVERTED_VBUS_ENABLE_LINE + + #else + + #error Unsupported architecture for this LUFA configuration file. + + #endif +#endif diff --git a/Demos/Device/ClassDriver/VirtualSerialMouse/Descriptors.c b/Demos/Device/ClassDriver/VirtualSerialMouse/Descriptors.c index 999712185..3fb00a1a1 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMouse/Descriptors.c +++ b/Demos/Device/ClassDriver/VirtualSerialMouse/Descriptors.c @@ -37,17 +37,6 @@ #include "Descriptors.h" -/* On some devices, there is a factory set internal serial number which can be automatically sent to the host as - * the device's serial number when the Device Descriptor's .SerialNumStrIndex entry is set to USE_INTERNAL_SERIAL. - * This allows the host to track a device across insertions on different ports, allowing them to retain allocated - * resources like COM port numbers and drivers. On demos using this feature, give a warning on unsupported devices - * so that the user can supply their own serial number descriptor instead or remove the USE_INTERNAL_SERIAL value - * from the Device Descriptor (forcing the host to generate a serial number for each device from the VID, PID and - * port location). - */ -#if (USE_INTERNAL_SERIAL == NO_DESCRIPTOR) - #warning USE_INTERNAL_SERIAL is not available on this AVR - please manually construct a device serial descriptor. -#endif /** HID class report descriptor. This is a special descriptor constructed with values from the * USBIF HID class specification to describe the reports and capabilities of the HID device. This diff --git a/Demos/Device/ClassDriver/VirtualSerialMouse/VirtualSerialMouse.h b/Demos/Device/ClassDriver/VirtualSerialMouse/VirtualSerialMouse.h index 22f86e590..7a5c1d762 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMouse/VirtualSerialMouse.h +++ b/Demos/Device/ClassDriver/VirtualSerialMouse/VirtualSerialMouse.h @@ -45,7 +45,6 @@ #include "Descriptors.h" - #include <LUFA/Version.h> #include <LUFA/Drivers/Board/LEDs.h> #include <LUFA/Drivers/Board/Joystick.h> #include <LUFA/Drivers/Board/Buttons.h> diff --git a/Demos/Device/ClassDriver/VirtualSerialMouse/makefile b/Demos/Device/ClassDriver/VirtualSerialMouse/makefile index 57107acfe..592c91513 100644 --- a/Demos/Device/ClassDriver/VirtualSerialMouse/makefile +++ b/Demos/Device/ClassDriver/VirtualSerialMouse/makefile @@ -120,11 +120,7 @@ LUFA_PATH = ../../../.. # LUFA library compile-time options and predefined tokens -LUFA_OPTS = -D USB_DEVICE_ONLY -LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8 -LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1 -LUFA_OPTS += -D USE_FLASH_DESCRIPTORS -LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)" +LUFA_OPTS = -D USE_LUFA_CONFIG_HEADER # Create the LUFA source path variables by including the LUFA root makefile @@ -169,7 +165,7 @@ DEBUG = dwarf-2 # Each directory must be seperated by a space. # Use forward slashes for directory separators. # For a directory that has spaces, enclose it in quotes. -EXTRAINCDIRS = $(LUFA_PATH)/ +EXTRAINCDIRS = $(LUFA_PATH)/ Config/ # Compiler flag to set the C Standard level. |