diff options
Diffstat (limited to 'lib/lufa/Bootloaders/HID/BootloaderHID.txt')
| -rw-r--r-- | lib/lufa/Bootloaders/HID/BootloaderHID.txt | 105 |
1 files changed, 0 insertions, 105 deletions
diff --git a/lib/lufa/Bootloaders/HID/BootloaderHID.txt b/lib/lufa/Bootloaders/HID/BootloaderHID.txt deleted file mode 100644 index e340703c4..000000000 --- a/lib/lufa/Bootloaders/HID/BootloaderHID.txt +++ /dev/null @@ -1,105 +0,0 @@ -/** \file - * - * This file contains special DoxyGen information for the generation of the main page and other special - * documentation pages. It is not a project source file. - */ - -/** \mainpage HID Class USB AVR Bootloader - * - * \section SSec_Compat Demo Compatibility: - * - * The following list indicates what microcontrollers are compatible with this demo. - * - * \li Series 7 USB AVRs (AT90USBxxx7) - * \li Series 6 USB AVRs (AT90USBxxx6) - * \li Series 4 USB AVRs (ATMEGAxxU4) - * \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2) - * - * \section SSec_Info USB Information: - * - * The following table gives a rundown of the USB utilization of this demo. - * - * <table> - * <tr> - * <td><b>USB Mode:</b></td> - * <td>Device</td> - * </tr> - * <tr> - * <td><b>USB Class:</b></td> - * <td>Human Interface Device Class (HID)</td> - * </tr> - * <tr> - * <td><b>USB Subclass:</b></td> - * <td>N/A</td> - * </tr> - * <tr> - * <td><b>Relevant Standards:</b></td> - * <td>USBIF HID Class Standard \n - * Teensy Programming Protocol Specification</td> - * </tr> - * <tr> - * <td><b>Supported USB Speeds:</b></td> - * <td>Low Speed Mode \n - * Full Speed Mode</td> - * </tr> - * </table> - * - * \section SSec_Description Project Description: - * - * This bootloader enumerates to the host as a HID Class device, allowing for device FLASH programming through - * the supplied command line software, which is a modified version of Paul's TeensyHID Command Line loader code - * from PJRC (used with permission). This bootloader is deliberately non-compatible with the proprietary PJRC - * HalfKay bootloader GUI; only the command line interface software accompanying this bootloader will work with it. - * - * Out of the box this bootloader builds for the AT90USB1287 with an 8KB bootloader section size, and will fit - * into 2KB of bootloader space for the Series 2 USB AVRs (ATMEGAxxU2, AT90USBxx2) or 4KB of bootloader space for - * all other models. If you wish to alter this size and/or change the AVR model, you will need to edit the MCU, - * FLASH_SIZE_KB and BOOT_SECTION_SIZE_KB values in the accompanying makefile. - * - * \warning <b>THIS BOOTLOADER IS NOT SECURE.</b> Malicious entities can recover written data, even if the device - * lockbits are set. - * - * \section Sec_Running Running the Bootloader - * - * This bootloader is designed to be started via the \c HWB mechanism of the USB AVRs; ground the \c HWB pin (see device - * datasheet) then momentarily ground \c /RESET to start the bootloader. This assumes the \c HWBE fuse is set and the - * \c BOOTRST fuse is cleared. - * - * \section Sec_Installation Driver Installation - * - * This bootloader uses the HID class driver inbuilt into all modern operating systems, thus no additional drivers - * need to be supplied for correct operation. - * - * \section Sec_HostApp Host Controller Application - * - * Due to licensing issues, the supplied bootloader is compatible with the HalfKay bootloader protocol designed - * by PJRC, but is <b>not compatible with the cross-platform loader GUI</b>. A modified version of the open source - * cross-platform TeensyLoader application is supplied, which can be compiled under most operating systems. The - * command-line loader application should remain compatible with genuine Teensy boards in addition to boards using - * this custom bootloader. - * - * Once compiled, programs can be loaded into the AVR's FLASH memory through the following example command: - * \code - * hid_bootloader_cli -mmcu=at90usb1287 Mouse.hex - * \endcode - * - * \section Sec_KnownIssues Known Issues: - * - * \par After loading an application, it is not run automatically on startup. - * Some USB AVR boards ship with the \c BOOTRST fuse set, causing the bootloader - * to run automatically when the device is reset. This booloader requires the - * \c BOOTRST be disabled and the HWBE fuse used instead to run the bootloader - * when needed. - * - * \section SSec_Options Project Options - * - * The following defines can be found in this demo, which can control the demo behaviour when defined, or changed in value. - * - * <table> - * <tr> - * <td> - * None - * </td> - * </tr> - * </table> - */ |