diff options
| -rw-r--r-- | Readme.txt | 16 | ||||
| -rw-r--r-- | firmware/main.c | 9 |
2 files changed, 15 insertions, 10 deletions
@@ -42,12 +42,12 @@ To allow maximum flexibility, micronucleus supports a configuration system. To c Currently, the following configurations are included and tested. Please check the subfolders /firmware/configurations/ for details. Hex files can be found in /releases. -t84_default - ATtiny84A default configuration - 1556 bytes -t841_default - ATtiny841 default configuration - 1608 bytes -t85_default - ATtiny85 default configuration - 1610 bytes -t85_aggressive - ATtiny85 smaller size - critical - 1418 bytes -t167_default - ATtiny167 default (uses xtal) - 1414 bytes -Nanite841 - Nanite841 firmware - 1632 bytes +t84_default - ATtiny84A default configuration - 1560 bytes +t841_default - ATtiny841 default configuration - 1612 bytes +t85_default - ATtiny85 default configuration - 1614 bytes +t85_aggressive - ATtiny85 smaller size - critical - 1422 bytes +t167_default - ATtiny167 default (uses xtal) - 1418 bytes +Nanite841 - Nanite841 firmware - 1634 bytes You can add your own configuration by adding a new folder to /firmware/configurations/. The folder has to contain a customized "Makefile.inc" and "bootloaderconfig.h". Feel free to supply a pull request if you added and tested a previously unsupported device. @@ -102,6 +102,10 @@ Changes connected to a USB3.0 port. - Fixes one bug that could lead to a deadlock if no USB was connected while the bootloader was active and noise was injected into the floating D+ input. + - D- line is released before the user program is started, instead of pulling it down. + This solves various issues where Micronucleus was not recognized after a reset. + Att: This may lead to a "Unknown device" pop-up in Windows, if the user program does + not have USB functionality itself. Credits ======= diff --git a/firmware/main.c b/firmware/main.c index 80b5d3a..ddd03e3 100644 --- a/firmware/main.c +++ b/firmware/main.c @@ -266,7 +266,7 @@ int main(void) { // adjust fastctr for 5ms timeout uint16_t fastctr=(uint16_t)(F_CPU/(1000.0f*15.0f/5.0f)); - uint8_t resetctr=100; + uint8_t resetctr=100; do { if ((USBIN & USBMASK) !=0) resetctr=100; @@ -303,8 +303,6 @@ int main(void) { OSCCAL = osccal_tmp; #endif - - if (command==cmd_exit) { if (!fastctr) break; // Only exit after 5 ms timeout } else { @@ -315,10 +313,12 @@ int main(void) { // This is usbpoll() minus reset logic and double buffering int8_t len; len = usbRxLen - 3; + if(len >= 0){ usbProcessRx(usbRxBuf + 1, len); // only single buffer due to in-order processing usbRxLen = 0; /* mark rx buffer as available */ } + if(usbTxLen & 0x10){ /* transmit system idle */ if(usbMsgLen != USB_NO_MSG){ /* transmit data pending? */ usbBuildTxBlock(); @@ -359,7 +359,8 @@ int main(void) { LED_EXIT(); - usbDeviceDisconnect(); /* Disconnect micronucleus */ + initHardware(); /* Disconnect micronucleus */ + USB_INTR_ENABLE = 0; USB_INTR_CFG = 0; /* also reset config bits */ |