#  -*- mode: python; -*-
#============================================================================
# Python configuration setup for 'xm create'.
# This script sets the parameters used when a domain is created using 'xm create'.
# You use a separate script for each domain you want to create, or 
# you can set the parameters for the domain on the xm command line.
#============================================================================

#----------------------------------------------------------------------------
# PV GRUB image file.
kernel = "pv-grub.gz"

# Optional provided menu.lst.
#ramdisk = "/boot/guests/menu.lst"

# Sets path to menu.lst
extra = "(hd0,0)/boot/grub/menu.lst"
# can be a TFTP-served path (DHCP will automatically be run)
# extra = "(nd)/netboot/menu.lst"
# can be configured automatically by GRUB's DHCP option 150 (see grub manual)
# extra = ""

# Initial memory allocation (in megabytes) for the new domain.
#
# WARNING: Creating a domain with insufficient memory may cause out of
#          memory errors. The domain needs enough memory to boot kernel
#          and modules. Allocating less than 32MBs is not recommended.
memory = 128

# A name for your domain. All domains must have different names.
name = "ExampleDomain"

# 128-bit UUID for the domain.  The default behavior is to generate a new UUID
# on each call to 'xm create'.
#uuid = "06ed00fe-1162-4fc4-b5d8-11993ee4a8b9"

# List of which CPUS this domain is allowed to use, default Xen picks
#cpus = ""         # leave to Xen to pick
#cpus = "0"        # all vcpus run on CPU0
#cpus = "0-3,5,^1" # all vcpus run on cpus 0,2,3,5
#cpus = ["2", "3"] # VCPU0 runs on CPU2, VCPU1 runs on CPU3

# Number of Virtual CPUS to use, default is 1
#vcpus = 1

#----------------------------------------------------------------------------
# Define network interfaces.

# By default, no network interfaces are configured.  You may have one created
# with sensible defaults using an empty vif clause:
#
# vif = [ '' ]
#
# or optionally override backend, bridge, ip, mac, script, type, or vifname:
#
# vif = [ 'mac=00:16:3e:00:00:11, bridge=xenbr0' ]
#
# or more than one interface may be configured:
#
# vif = [ '', 'bridge=xenbr1' ]

vif = [ '' ]

#----------------------------------------------------------------------------
# Define the disk devices you want the domain to have access to, and
# what you want them accessible as.
# Each disk entry is of the form phy:UNAME,DEV,MODE
# where UNAME is the device, DEV is the device name the domain will see,
# and MODE is r for read-only, w for read-write.

disk = [ 'phy:hda1,hda1,w' ]

#----------------------------------------------------------------------------
# Define frame buffer device.
#
# By default, no frame buffer device is configured.
#
# To create one using the SDL backend and sensible defaults:
#
# vfb = [ 'sdl=1' ]
#
# This uses environment variables XAUTHORITY and DISPLAY.  You
# can override that:
#
# vfb = [ 'sdl=1,xauthority=/home/bozo/.Xauthority,display=:1' ]
#
# To create one using the VNC backend and sensible defaults:
#
# vfb = [ 'vnc=1' ]
#
# The backend listens on 127.0.0.1 port 5900+N by default, where N is
# the domain ID.  You can override both address and N:
#
# vfb = [ 'vnc=1,vnclisten=127.0.0.1,vncdisplay=1' ]
#
# Or you can bind the first unused port above 5900:
#
# vfb = [ 'vnc=1,vnclisten=0.0.0.0,vncunused=1' ]
#
# You can override the password:
#
# vfb = [ 'vnc=1,vncpasswd=MYPASSWD' ]
#
# Empty password disables authentication.  Defaults to the vncpasswd
# configured in xend-config.sxp.

#----------------------------------------------------------------------------
# Configure the behaviour when a domain exits.  There are three 'reasons'
# for a domain to stop: poweroff, reboot, and crash.  For each of these you
# may specify:
#
#   "destroy",        meaning that the domain is cleaned up as normal;
#   "restart",        meaning that a new domain is started in place of the old
#                     one;
#   "preserve",       meaning that no clean-up is done until the domain is
#                     manually destroyed (using xm destroy, for example); or
#   "rename-restart", meaning that the old domain is not cleaned up, but is
#                     renamed and a new domain started in its place.
#
# In the event a domain stops due to a crash, you have the additional options:
#
#   "coredump-destroy", meaning dump the crashed domain's core and then destroy;
#   "coredump-restart', meaning dump the crashed domain's core and the restart.
#
# The default is
#
#   on_poweroff = 'destroy'
#   on_reboot   = 'restart'
#   on_crash    = 'restart'
#
# For backwards compatibility we also support the deprecated option restart
#
# restart = 'onreboot' means on_poweroff = 'destroy'
#                            on_reboot   = 'restart'
#                            on_crash    = 'destroy'
#
# restart = 'always'   means on_poweroff = 'restart'
#                            on_reboot   = 'restart'
#                            on_crash    = 'restart'
#
# restart = 'never'    means on_poweroff = 'destroy'
#                            on_reboot   = 'destroy'
#                            on_crash    = 'destroy'

#on_poweroff = 'destroy'
#on_reboot   = 'restart'
#on_crash    = 'restart'

#-----------------------------------------------------------------------------
#   Configure PVSCSI devices:
#
#vscsi=[ 'PDEV, VDEV' ]
#
#   PDEV   gives physical SCSI device to be attached to specified guest
#          domain by one of the following identifier format.
#          - XX:XX:XX:XX (4-tuples with decimal notation which shows
#                          "host:channel:target:lun")
#          - /dev/sdxx or sdx
#          - /dev/stxx or stx
#          - /dev/sgxx or sgx
#          - result of 'scsi_id -gu -s'.
#            ex. # scsi_id -gu -s /block/sdb
#                  36000b5d0006a0000006a0257004c0000
#
#   VDEV   gives virtual SCSI device by 4-tuples (XX:XX:XX:XX) as 
#          which the specified guest domain recognize.
#

#vscsi = [ '/dev/sdx, 0:0:0:0' ]

#============================================================================