diff options
Diffstat (limited to 'watch-library/hal/include/hpl_i2c_m_sync.h')
-rw-r--r-- | watch-library/hal/include/hpl_i2c_m_sync.h | 185 |
1 files changed, 0 insertions, 185 deletions
diff --git a/watch-library/hal/include/hpl_i2c_m_sync.h b/watch-library/hal/include/hpl_i2c_m_sync.h deleted file mode 100644 index ce173ae2..00000000 --- a/watch-library/hal/include/hpl_i2c_m_sync.h +++ /dev/null @@ -1,185 +0,0 @@ -/** - * \file - * - * \brief I2C Master Hardware Proxy Layer(HPL) declaration. - * - * Copyright (c) 2014-2018 Microchip Technology Inc. and its subsidiaries. - * - * \asf_license_start - * - * \page License - * - * Subject to your compliance with these terms, you may use Microchip - * software and any derivatives exclusively with Microchip products. - * It is your responsibility to comply with third party license terms applicable - * to your use of third party software (including open source software) that - * may accompany Microchip software. - * - * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, - * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, - * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, - * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE - * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL - * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE - * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE - * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT - * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY - * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, - * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE. - * - * \asf_license_stop - * - */ -#ifndef _HPL_I2C_M_SYNC_H_INCLUDED -#define _HPL_I2C_M_SYNC_H_INCLUDED - -#include <compiler.h> - -#ifdef __cplusplus -extern "C" { -#endif - -/** - * \brief i2c flags - */ -#define I2C_M_RD 0x0001 /* read data, from slave to master */ -#define I2C_M_BUSY 0x0100 -#define I2C_M_TEN 0x0400 /* this is a ten bit chip address */ -#define I2C_M_SEVEN 0x0800 /* this is a seven bit chip address */ -#define I2C_M_FAIL 0x1000 -#define I2C_M_STOP 0x8000 /* if I2C_FUNC_PROTOCOL_MANGLING */ - -/** - * \brief i2c Return codes - */ -#define I2C_OK 0 /* Operation successful */ -#define I2C_ACK -1 /* Received ACK from device on I2C bus */ -#define I2C_NACK -2 /* Received NACK from device on I2C bus */ -#define I2C_ERR_ARBLOST -3 /* Arbitration lost */ -#define I2C_ERR_BAD_ADDRESS -4 /* Bad address */ -#define I2C_ERR_BUS -5 /* Bus error */ -#define I2C_ERR_BUSY -6 /* Device busy */ -#define I2c_ERR_PACKAGE_COLLISION -7 /* Package collision */ - -/** - * \brief i2c I2C Modes - */ -#define I2C_STANDARD_MODE 0x00 -#define I2C_FASTMODE 0x01 -#define I2C_HIGHSPEED_MODE 0x02 - -/** - * \brief i2c master message structure - */ -struct _i2c_m_msg { - uint16_t addr; - volatile uint16_t flags; - int32_t len; - uint8_t * buffer; -}; - -/** - * \brief i2c master service - */ -struct _i2c_m_service { - struct _i2c_m_msg msg; - uint16_t mode; - uint16_t trise; -}; - -/** - * \brief i2c sync master device structure - */ -struct _i2c_m_sync_device { - struct _i2c_m_service service; - void * hw; -}; - -/** - * \name HPL functions - */ - -/** - * \brief Initialize I2C - * - * This function does low level I2C configuration. - * - * \param[in] i2c_dev The pointer to i2c device structure - * \param[in] hw The pointer to hardware instance - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_m_sync_init(struct _i2c_m_sync_device *const i2c_dev, void *const hw); - -/** - * \brief Deinitialize I2C - * - * \param[in] i2c_dev The pointer to i2c device structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_m_sync_deinit(struct _i2c_m_sync_device *const i2c_dev); - -/** - * \brief Enable I2C module - * - * This function does low level I2C enable. - * - * \param[in] i2c_dev The pointer to i2c device structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_m_sync_enable(struct _i2c_m_sync_device *const i2c_dev); - -/** - * \brief Disable I2C module - * - * This function does low level I2C disable. - * - * \param[in] i2c_dev The pointer to i2c device structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_m_sync_disable(struct _i2c_m_sync_device *const i2c_dev); - -/** - * \brief Transfer data by I2C - * - * This function does low level I2C data transfer. - * - * \param[in] i2c_dev The pointer to i2c device structure - * \param[in] msg The pointer to i2c msg structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_m_sync_transfer(struct _i2c_m_sync_device *const i2c_dev, struct _i2c_m_msg *msg); - -/** - * \brief Set baud rate of I2C - * - * This function does low level I2C set baud rate. - * - * \param[in] i2c_dev The pointer to i2c device structure - * \param[in] clkrate The clock rate(KHz) input to i2c module - * \param[in] baudrate The demand baud rate(KHz) of i2c module - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_m_sync_set_baudrate(struct _i2c_m_sync_device *const i2c_dev, uint32_t clkrate, uint32_t baudrate); - -/** - * \brief Send send condition on the I2C bus - * - * This function will generate a stop condition on the I2C bus - * - * \param[in] i2c_dev The pointer to i2c device struct - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_m_sync_send_stop(struct _i2c_m_sync_device *const i2c_dev); - -#ifdef __cplusplus -} -#endif - -#endif |