1 files changed, 0 insertions, 60 deletions
diff --git a/tinyusb/hw/bsp/nutiny_sdk_nuc505/board.mk b/tinyusb/hw/bsp/nutiny_sdk_nuc505/board.mk
deleted file mode 100755
index e8514347..00000000
--- a/tinyusb/hw/bsp/nutiny_sdk_nuc505/board.mk
+++ /dev/null
@@ -1,60 +0,0 @@
-DEPS_SUBMODULES += hw/mcu/nuvoton
-
-CFLAGS += \
-  -flto \
-  -mthumb \
-  -mabi=aapcs-linux \
-  -mcpu=cortex-m4 \
-  -mfloat-abi=hard \
-  -mfpu=fpv4-sp-d16 \
-  -DCFG_TUSB_MCU=OPT_MCU_NUC505
-
-# All source paths should be relative to the top level.
-LD_FILE = hw/bsp/$(BOARD)/nuc505_flashtoram.ld
-
-SRC_C += \
-  src/portable/nuvoton/nuc505/dcd_nuc505.c \
-  hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Source/system_NUC505Series.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/adc.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/clk.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/gpio.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/i2c.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/i2s.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/pwm.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/rtc.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/spi.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/spim.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/sys.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/timer.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/uart.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/wdt.c \
-  hw/mcu/nuvoton/nuc505/StdDriver/src/wwdt.c
-
-SRC_S += \
-  hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Source/GCC/startup_NUC505Series.S
-
-INC += \
-  $(TOP)/hw/mcu/nuvoton/nuc505/Device/Nuvoton/NUC505Series/Include \
-  $(TOP)/hw/mcu/nuvoton/nuc505/StdDriver/inc \
-  $(TOP)/hw/mcu/nuvoton/nuc505/CMSIS/Include
-
-# For freeRTOS port source
-FREERTOS_PORT = ARM_CM4F
-
-# For flash-jlink target
-JLINK_DEVICE = NUC505YO13Y
-
-# Note
-# To be able to program the SPI flash, it need to boot with ICP mode "1011". 
-# However, in ICP mode, opencod cannot establish connection to the mcu. 
-# Therefore, there is no easy command line flash for NUC505
-# It is probably better to just use Nuvoton NuMicro ICP programming on windows to program the board
-# - 1111 "SPI" (run from internal flash)
-# - 1110 "USB" (mass storage emulator that accepts a .bin file)
-# - 0111 "ICE-SPI" (allow external debugger access, but may not be programmable)
-# - 1011 ICP mode (programmable via NuMicro ICP programming tool)
-
-# Flash using Nuvoton's openocd fork at https://github.com/OpenNuvoton/OpenOCD-Nuvoton
-# Please compile and install it from github source
-flash: $(BUILD)/$(PROJECT).elf
-	openocd -f interface/nulink.cfg -f target/numicroM4.cfg -c "program $< reset exit"