diff options
Diffstat (limited to 'Smol Watch Project/My Project/hal/include/hpl_i2c_s_sync.h')
-rw-r--r-- | Smol Watch Project/My Project/hal/include/hpl_i2c_s_sync.h | 184 |
1 files changed, 0 insertions, 184 deletions
diff --git a/Smol Watch Project/My Project/hal/include/hpl_i2c_s_sync.h b/Smol Watch Project/My Project/hal/include/hpl_i2c_s_sync.h deleted file mode 100644 index 93b59345..00000000 --- a/Smol Watch Project/My Project/hal/include/hpl_i2c_s_sync.h +++ /dev/null @@ -1,184 +0,0 @@ -/** - * \file - * - * \brief I2C Slave Hardware Proxy Layer(HPL) declaration. - * - * Copyright (c) 2015-2018 Microchip Technology Inc. and its subsidiaries. - * - * \asf_license_start - * - * \page License - * - * Subject to your compliance with these terms, you may use Microchip - * software and any derivatives exclusively with Microchip products. - * It is your responsibility to comply with third party license terms applicable - * to your use of third party software (including open source software) that - * may accompany Microchip software. - * - * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, - * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, - * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, - * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE - * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL - * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE - * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE - * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT - * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY - * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, - * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE. - * - * \asf_license_stop - * - */ -#ifndef _HPL_I2C_S_SYNC_H_INCLUDED -#define _HPL_I2C_S_SYNC_H_INCLUDED - -#include <compiler.h> - -#ifdef __cplusplus -extern "C" { -#endif - -/** - * \brief I2C Slave status type - */ -typedef uint32_t i2c_s_status_t; - -/** - * \brief i2c slave device structure - */ -struct _i2c_s_sync_device { - void *hw; -}; - -#include <compiler.h> - -/** - * \name HPL functions - */ - -/** - * \brief Initialize synchronous I2C slave - * - * This function does low level I2C configuration. - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_s_sync_init(struct _i2c_s_sync_device *const device, void *const hw); - -/** - * \brief Deinitialize synchronous I2C slave - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_s_sync_deinit(struct _i2c_s_sync_device *const device); - -/** - * \brief Enable I2C module - * - * This function does low level I2C enable. - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_s_sync_enable(struct _i2c_s_sync_device *const device); - -/** - * \brief Disable I2C module - * - * This function does low level I2C disable. - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_s_sync_disable(struct _i2c_s_sync_device *const device); - -/** - * \brief Check if 10-bit addressing mode is on - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Cheking status - * \retval 1 10-bit addressing mode is on - * \retval 0 10-bit addressing mode is off - */ -int32_t _i2c_s_sync_is_10bit_addressing_on(const struct _i2c_s_sync_device *const device); - -/** - * \brief Set I2C slave address - * - * \param[in] device The pointer to i2c slave device structure - * \param[in] address Address to set - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_s_sync_set_address(struct _i2c_s_sync_device *const device, const uint16_t address); - -/** - * \brief Write a byte to the given I2C instance - * - * \param[in] device The pointer to i2c slave device structure - * \param[in] data Data to write - */ -void _i2c_s_sync_write_byte(struct _i2c_s_sync_device *const device, const uint8_t data); - -/** - * \brief Retrieve I2C slave status - * - * \param[in] device The pointer to i2c slave device structure - * - *\return I2C slave status - */ -i2c_s_status_t _i2c_s_sync_get_status(const struct _i2c_s_sync_device *const device); - -/** - * \brief Clear the Data Ready interrupt flag - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Return 0 for success and negative value for error - */ -int32_t _i2c_s_sync_clear_data_ready_flag(const struct _i2c_s_sync_device *const device); - -/** - * \brief Read a byte from the given I2C instance - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Data received via I2C interface. - */ -uint8_t _i2c_s_sync_read_byte(const struct _i2c_s_sync_device *const device); - -/** - * \brief Check if I2C is ready to send next byte - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Status of the ready check. - * \retval true if the I2C is ready to send next byte - * \retval false if the I2C is not ready to send next byte - */ -bool _i2c_s_sync_is_byte_sent(const struct _i2c_s_sync_device *const device); - -/** - * \brief Check if there is data received by I2C - * - * \param[in] device The pointer to i2c slave device structure - * - * \return Status of the data received check. - * \retval true if the I2C has received a byte - * \retval false if the I2C has not received a byte - */ -bool _i2c_s_sync_is_byte_received(const struct _i2c_s_sync_device *const device); - -#ifdef __cplusplus -} -#endif - -#endif /* _HPL_I2C_S_SYNC_H_INCLUDED */ |