diff options
Diffstat (limited to 'Smol Watch Project/My Project/hal/include/hpl_gpio.h')
| -rw-r--r-- | Smol Watch Project/My Project/hal/include/hpl_gpio.h | 185 |
1 files changed, 0 insertions, 185 deletions
diff --git a/Smol Watch Project/My Project/hal/include/hpl_gpio.h b/Smol Watch Project/My Project/hal/include/hpl_gpio.h deleted file mode 100644 index 5cdd387b..00000000 --- a/Smol Watch Project/My Project/hal/include/hpl_gpio.h +++ /dev/null @@ -1,185 +0,0 @@ -/** - * \file - * - * \brief Port related functionality declaration. - * - * Copyright (c) 2014-2018 Microchip Technology Inc. and its subsidiaries. - * - * \asf_license_start - * - * \page License - * - * Subject to your compliance with these terms, you may use Microchip - * software and any derivatives exclusively with Microchip products. - * It is your responsibility to comply with third party license terms applicable - * to your use of third party software (including open source software) that - * may accompany Microchip software. - * - * THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, - * WHETHER EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, - * INCLUDING ANY IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, - * AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL MICROCHIP BE - * LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE, INCIDENTAL OR CONSEQUENTIAL - * LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND WHATSOEVER RELATED TO THE - * SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS BEEN ADVISED OF THE - * POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE FULLEST EXTENT - * ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN ANY WAY - * RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY, - * THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE. - * - * \asf_license_stop - * - */ - -#ifndef _HPL_GPIO_H_INCLUDED -#define _HPL_GPIO_H_INCLUDED - -/** - * \addtogroup HPL Port - * - * \section hpl_port_rev Revision History - * - v1.0.0 Initial Release - * - *@{ - */ - -#include <compiler.h> - -#ifdef __cplusplus -extern "C" { -#endif -/** - * \brief Macros for the pin and port group, lower 5 - * bits stands for pin number in the group, higher 3 - * bits stands for port group - */ -#define GPIO_PIN(n) (((n)&0x1Fu) << 0) -#define GPIO_PORT(n) ((n) >> 5) -#define GPIO(port, pin) ((((port)&0x7u) << 5) + ((pin)&0x1Fu)) -#define GPIO_PIN_FUNCTION_OFF 0xffffffff - -/** - * \brief PORT pull mode settings - */ -enum gpio_pull_mode { GPIO_PULL_OFF, GPIO_PULL_UP, GPIO_PULL_DOWN }; - -/** - * \brief PORT direction settins - */ -enum gpio_direction { GPIO_DIRECTION_OFF, GPIO_DIRECTION_IN, GPIO_DIRECTION_OUT }; - -/** - * \brief PORT group abstraction - */ - -enum gpio_port { GPIO_PORTA, GPIO_PORTB, GPIO_PORTC, GPIO_PORTD, GPIO_PORTE }; - -/** - * \name HPL functions - */ -//@{ -/** - * \brief Port initialization function - * - * Port initialization function should setup the port module based - * on a static configuration file, this function should normally - * not be called directly, but is a part of hal_init() - */ -void _gpio_init(void); - -/** - * \brief Set direction on port with mask - * - * Set data direction for each pin, or disable the pin - * - * \param[in] port Ports are grouped into groups of maximum 32 pins, - * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc - * \param[in] mask Bit mask where 1 means apply direction setting to the - * corresponding pin - * \param[in] direction GPIO_DIRECTION_OFF = set pin direction to input - * and disable input buffer to disable the pin - * GPIO_DIRECTION_IN = set pin direction to input - * and enable input buffer to enable the pin - * GPIO_DIRECTION_OUT = set pin direction to output - * and disable input buffer - */ -static inline void _gpio_set_direction(const enum gpio_port port, const uint32_t mask, - const enum gpio_direction direction); - -/** - * \brief Set output level on port with mask - * - * Sets output state on pin to high or low with pin masking - * - * \param[in] port Ports are grouped into groups of maximum 32 pins, - * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc - * \param[in] mask Bit mask where 1 means apply direction setting to - * the corresponding pin - * \param[in] level true = pin level is set to 1 - * false = pin level is set to 0 - */ -static inline void _gpio_set_level(const enum gpio_port port, const uint32_t mask, const bool level); - -/** - * \brief Change output level to the opposite with mask - * - * Change pin output level to the opposite with pin masking - * - * \param[in] port Ports are grouped into groups of maximum 32 pins, - * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc - * \param[in] mask Bit mask where 1 means apply direction setting to - * the corresponding pin - */ -static inline void _gpio_toggle_level(const enum gpio_port port, const uint32_t mask); - -/** - * \brief Get input levels on all port pins - * - * Get input level on all port pins, will read IN register if configured to - * input and OUT register if configured as output - * - * \param[in] port Ports are grouped into groups of maximum 32 pins, - * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc - */ -static inline uint32_t _gpio_get_level(const enum gpio_port port); - -/** - * \brief Set pin pull mode - * - * Set pull mode on a single pin - * - * \notice This function will automatically change pin direction to input - * - * \param[in] port Ports are grouped into groups of maximum 32 pins, - * GPIO_PORTA = group 0, GPIO_PORTB = group 1, etc - * \param[in] pin The pin in the group that pull mode should be selected - * for - * \param[in] pull_mode GPIO_PULL_OFF = pull resistor on pin is disabled - * GPIO_PULL_DOWN = pull resistor on pin will pull pin - * level to ground level - * GPIO_PULL_UP = pull resistor on pin will pull pin - * level to VCC - */ -static inline void _gpio_set_pin_pull_mode(const enum gpio_port port, const uint8_t pin, - const enum gpio_pull_mode pull_mode); - -/** - * \brief Set gpio function - * - * Select which function a gpio is used for - * - * \param[in] gpio The gpio to set function for - * \param[in] function The gpio function is given by a 32-bit wide bitfield - * found in the header files for the device - * - */ -static inline void _gpio_set_pin_function(const uint32_t gpio, const uint32_t function); - -#include <hpl_gpio_base.h> -//@} - -#ifdef __cplusplus -} -#endif -/**@}*/ -#endif /* _HPL_GPIO_H_INCLUDED */ |