diff options
Diffstat (limited to 'Smol Watch Project/My Project/Config/hpl_rtc_config.h')
| -rw-r--r-- | Smol Watch Project/My Project/Config/hpl_rtc_config.h | 318 |
1 files changed, 0 insertions, 318 deletions
diff --git a/Smol Watch Project/My Project/Config/hpl_rtc_config.h b/Smol Watch Project/My Project/Config/hpl_rtc_config.h deleted file mode 100644 index 9085ca37..00000000 --- a/Smol Watch Project/My Project/Config/hpl_rtc_config.h +++ /dev/null @@ -1,318 +0,0 @@ -/* Auto-generated config file hpl_rtc_config.h */ -#ifndef HPL_RTC_CONFIG_H -#define HPL_RTC_CONFIG_H - -// <<< Use Configuration Wizard in Context Menu >>> - -// <h> Basic settings - -#ifndef CONF_RTC_ENABLE -#define CONF_RTC_ENABLE 1 -#endif - -// <q> Force reset RTC on initialization -// <i> Force RTC to reset on initialization. -// <i> Note that the previous power down data in RTC is lost if it's enabled. -// <id> rtc_arch_init_reset -#ifndef CONF_RTC_INIT_RESET -#define CONF_RTC_INIT_RESET 0 -#endif - -// <o> Prescaler configuration -// <0x0=>OFF(Peripheral clock divided by 1) -// <0x1=>Peripheral clock divided by 1 -// <0x2=>Peripheral clock divided by 2 -// <0x3=>Peripheral clock divided by 4 -// <0x4=>Peripheral clock divided by 8 -// <0x5=>Peripheral clock divided by 16 -// <0x6=>Peripheral clock divided by 32 -// <0x7=>Peripheral clock divided by 64 -// <0x8=>Peripheral clock divided by 128 -// <0x9=>Peripheral clock divided by 256 -// <0xA=>Peripheral clock divided by 512 -// <0xB=>Peripheral clock divided by 1024 -// <i> These bits define the RTC clock relative to the peripheral clock -// <id> rtc_arch_prescaler -#ifndef CONF_RTC_PRESCALER - -#define CONF_RTC_PRESCALER 0xb - -#endif - -#ifndef CONF_RTC_COMP_VAL - -#define CONF_RTC_COMP_VAL 0 - -#endif - -// <e> RTC Tamper Input 0 settings -// <id> tamper_input_0_settings -#ifndef CONF_TAMPER_INPUT_0_SETTINGS -#define CONF_TAMPER_INPUT_0_SETTINGS 0 -#endif - -// <q> Tamper Level Settings -// <i> Indicates Tamper input 0 level -// <id> tamper_level_0 -#ifndef CONF_RTC_TAMP_LVL_0 -#define CONF_RTC_TAMP_LVL_0 0 -#endif - -// <o> RTC Tamper Input Action -// <0x0=>OFF(Disabled) -// <0x1=>Wake and Set Tamper Flag -// <0x2=>Capture Timestamp and Set Tamper Flag -// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. -// <i> These bits define the RTC Tamper Input Action to be performed -// <id> rtc_tamper_input_action_0 -#ifndef CONF_RTC_TAMPER_INACT_0 -#define CONF_RTC_TAMPER_INACT_0 0 -#endif - -// <q> Debounce Enable for Tamper Input -// <i> Indicates Debounce should be enabled for Tamper input 0 -// <id> tamper_debounce_enable_0 -#ifndef CONF_RTC_TAMP_DEBNC_0 -#define CONF_RTC_TAMP_DEBNC_0 0 -#endif - -// </e> - -// <e> RTC Tamper Input 1 settings -// <id> tamper_input_1_settings -#ifndef CONF_TAMPER_INPUT_1_SETTINGS -#define CONF_TAMPER_INPUT_1_SETTINGS 0 -#endif - -// <q> Tamper Level Settings -// <i> Indicates Tamper input 1 level -// <id> tamper_level_1 -#ifndef CONF_RTC_TAMP_LVL_1 -#define CONF_RTC_TAMP_LVL_1 0 -#endif - -// <o> RTC Tamper Input Action -// <0x0=>OFF(Disabled) -// <0x1=>Wake and Set Tamper Flag -// <0x2=>Capture Timestamp and Set Tamper Flag -// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. -// <i> These bits define the RTC Tamper Input Action to be performed -// <id> rtc_tamper_input_action_1 -#ifndef CONF_RTC_TAMPER_INACT_1 -#define CONF_RTC_TAMPER_INACT_1 0 -#endif - -// <q> Debounce Enable for Tamper Input -// <i> Indicates Debounce should be enabled for Tamper input 1 -// <id> tamper_debounce_enable_1 -#ifndef CONF_RTC_TAMP_DEBNC_1 -#define CONF_RTC_TAMP_DEBNC_1 0 -#endif - -// </e> - -// <e> RTC Tamper Input 2 settings -// <id> tamper_input_2_settings -#ifndef CONF_TAMPER_INPUT_2_SETTINGS -#define CONF_TAMPER_INPUT_2_SETTINGS 0 -#endif - -// <q> Tamper Level Settings -// <i> Indicates Tamper input 2 level -// <id> tamper_level_2 -#ifndef CONF_RTC_TAMP_LVL_2 -#define CONF_RTC_TAMP_LVL_2 0 -#endif - -// <o> RTC Tamper Input Action -// <0x0=>OFF(Disabled) -// <0x1=>Wake and Set Tamper Flag -// <0x2=>Capture Timestamp and Set Tamper Flag -// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. -// <i> These bits define the RTC Tamper Input Action to be performed -// <id> rtc_tamper_input_action_2 -#ifndef CONF_RTC_TAMPER_INACT_2 -#define CONF_RTC_TAMPER_INACT_2 0 -#endif - -// <q> Debounce Enable for Tamper Input -// <i> Indicates Debounce should be enabled for Tamper input 2 -// <id> tamper_debounce_enable_2 -#ifndef CONF_RTC_TAMP_DEBNC_2 -#define CONF_RTC_TAMP_DEBNC_2 0 -#endif - -// </e> - -// <e> RTC Tamper Input 3 settings -// <id> tamper_input_3_settings -#ifndef CONF_TAMPER_INPUT_3_SETTINGS -#define CONF_TAMPER_INPUT_3_SETTINGS 0 -#endif - -// <q> Tamper Level Settings -// <i> Indicates Tamper input 3 level -// <id> tamper_level_3 -#ifndef CONF_RTC_TAMP_LVL_3 -#define CONF_RTC_TAMP_LVL_3 0 -#endif - -// <o> RTC Tamper Input Action -// <0x0=>OFF(Disabled) -// <0x1=>Wake and Set Tamper Flag -// <0x2=>Capture Timestamp and Set Tamper Flag -// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. -// <i> These bits define the RTC Tamper Input Action to be performed -// <id> rtc_tamper_input_action_3 -#ifndef CONF_RTC_TAMPER_INACT_3 -#define CONF_RTC_TAMPER_INACT_3 0 -#endif - -// <q> Debounce Enable for Tamper Input -// <i> Indicates Debounce should be enabled for Tamper input 3 -// <id> tamper_debounce_enable_3 -#ifndef CONF_RTC_TAMP_DEBNC_3 -#define CONF_RTC_TAMP_DEBNC_3 0 -#endif - -// </e> - -// <e> RTC Tamper Input 4 settings -// <id> tamper_input_4_settings -#ifndef CONF_TAMPER_INPUT_4_SETTINGS -#define CONF_TAMPER_INPUT_4_SETTINGS 0 -#endif - -// <q> Tamper Level Settings -// <i> Indicates Tamper input 4 level -// <id> tamper_level_4 -#ifndef CONF_RTC_TAMP_LVL_4 -#define CONF_RTC_TAMP_LVL_4 0 -#endif - -// <o> RTC Tamper Input Action -// <0x0=>OFF(Disabled) -// <0x1=>Wake and Set Tamper Flag -// <0x2=>Capture Timestamp and Set Tamper Flag -// <0x3=>Active Layer Mode.IN and OUT pin is used.Timestamp is also captured. -// <i> These bits define the RTC Tamper Input Action to be performed -// <id> rtc_tamper_input_action_4 -#ifndef CONF_RTC_TAMPER_INACT_4 -#define CONF_RTC_TAMPER_INACT_4 0 -#endif - -// <q> Debounce Enable for Tamper Input -// <i> Indicates Debounce should be enabled for Tamper input 4 -// <id> tamper_debounce_enable_4 -#ifndef CONF_RTC_TAMP_DEBNC_4 -#define CONF_RTC_TAMP_DEBNC_4 0 -#endif - -// </e> - -// <o> RTC Tamper Active Layer Frequency Prescalar -// <0x0=>DIV2 CLK_RTC_OUT is CLK_RTC /2 -// <0x1=>DIV4 CLK_RTC_OUT is CLK_RTC /4 -// <0x2=>DIV8 CLK_RTC_OUT is CLK_RTC /8 -// <0x3=>DIV16 CLK_RTC_OUT is CLK_RTC /16 -// <0x4=>DIV32 CLK_RTC_OUT is CLK_RTC /32 -// <0x5=>DIV64 CLK_RTC_OUT is CLK_RTC /64 -// <0x6=>DIV128 CLK_RTC_OUT is CLK_RTC /128 -// <0x7=>DIV256 CLK_RTC_OUT is CLK_RTC /256 -// <i> These bits define the RTC Tamper Active Layer Frequecny Prescalar -// <id> rtc_tamper_active_layer_frequency_prescalar -#ifndef CONF_RTC_TAMP_ACT_LAYER_FREQ_PRES -#define CONF_RTC_TAMP_ACT_LAYER_FREQ_PRES 0 -#endif - -// <o> RTC Tamper Debounce Frequency Prescalar -// <0x0=>DIV2 CLK_RTC_DEB is CLK_RTC /2 -// <0x1=>DIV4 CLK_RTC_DEB is CLK_RTC /4 -// <0x2=>DIV8 CLK_RTC_DEB is CLK_RTC /8 -// <0x3=>DIV16 CLK_RTC_DEB is CLK_RTC /16 -// <0x4=>DIV32 CLK_RTC_DEB is CLK_RTC /32 -// <0x5=>DIV64 CLK_RTC_DEB is CLK_RTC /64 -// <0x6=>DIV128 CLK_RTC_DEB is CLK_RTC /128 -// <0x7=>DIV256 CLK_RTC_DEB is CLK_RTC /256 -// <i> These bits define the RTC Debounce Frequency Prescalar -// <id> rtc_tamper_debounce_frequency_prescalar -#ifndef CONF_RTC_TAMP_DEBF_PRES -#define CONF_RTC_TAMP_DEBF_PRES 0 -#endif - -// <e> Event control -// <id> rtc_event_control -#ifndef CONF_RTC_EVENT_CONTROL_ENABLE -#define CONF_RTC_EVENT_CONTROL_ENABLE 0 -#endif - -// <q> Periodic Interval 0 Event Output -// <i> This bit indicates whether Periodic interval 0 event is enabled and will be generated -// <id> rtc_pereo0 -#ifndef CONF_RTC_PEREO0 -#define CONF_RTC_PEREO0 0 -#endif -// <q> Periodic Interval 1 Event Output -// <i> This bit indicates whether Periodic interval 1 event is enabled and will be generated -// <id> rtc_pereo1 -#ifndef CONF_RTC_PEREO1 -#define CONF_RTC_PEREO1 0 -#endif -// <q> Periodic Interval 2 Event Output -// <i> This bit indicates whether Periodic interval 2 event is enabled and will be generated -// <id> rtc_pereo2 -#ifndef CONF_RTC_PEREO2 -#define CONF_RTC_PEREO2 0 -#endif -// <q> Periodic Interval 3 Event Output -// <i> This bit indicates whether Periodic interval 3 event is enabled and will be generated -// <id> rtc_pereo3 -#ifndef CONF_RTC_PEREO3 -#define CONF_RTC_PEREO3 0 -#endif -// <q> Periodic Interval 4 Event Output -// <i> This bit indicates whether Periodic interval 4 event is enabled and will be generated -// <id> rtc_pereo4 -#ifndef CONF_RTC_PEREO4 -#define CONF_RTC_PEREO4 0 -#endif -// <q> Periodic Interval 5 Event Output -// <i> This bit indicates whether Periodic interval 5 event is enabled and will be generated -// <id> rtc_pereo5 -#ifndef CONF_RTC_PEREO5 -#define CONF_RTC_PEREO5 0 -#endif -// <q> Periodic Interval 6 Event Output -// <i> This bit indicates whether Periodic interval 6 event is enabled and will be generated -// <id> rtc_pereo6 -#ifndef CONF_RTC_PEREO6 -#define CONF_RTC_PEREO6 0 -#endif -// <q> Periodic Interval 7 Event Output -// <i> This bit indicates whether Periodic interval 7 event is enabled and will be generated -// <id> rtc_pereo7 -#ifndef CONF_RTC_PEREO7 -#define CONF_RTC_PEREO7 0 -#endif - -// <q> Compare 0 Event Output -// <i> This bit indicates whether Compare O event is enabled and will be generated -// <id> rtc_cmpeo0 -#ifndef CONF_RTC_COMPE0 -#define CONF_RTC_COMPE0 0 -#endif - -// <q> Overflow Event Output -// <i> This bit indicates whether Overflow event is enabled and will be generated -// <id> rtc_ovfeo -#ifndef CONF_RTC_OVFEO -#define CONF_RTC_OVFEO 0 -#endif - -// </e> - -// </h> - -// <<< end of configuration section >>> - -#endif // HPL_RTC_CONFIG_H |