rename project files

3 files changed, 0 insertions, 225 deletions

diff --git a/apps/Sensor Watch Starter Project/app.c b/apps/Sensor Watch Starter Project/app.c
deleted file mode 100644
index fa887bae..00000000
--- a/apps/Sensor Watch Starter Project/app.c
+++ /dev/null
@@ -1,198 +0,0 @@
-#include <stdio.h>
-#include <string.h>
-#include "watch.h"
-
-//////////////////////////////////////////////////////////////////////////////////////////
-// This section sets up types and storage for our application state.
-// You can tear this out and replace it with whatever you want.
-typedef enum ApplicationMode {
-    MODE_HELLO = 0,
-    MODE_THERE
-} ApplicationMode;
-
-typedef enum LightColor {
-    COLOR_RED = 0,
-    COLOR_GREEN,
-    COLOR_YELLOW
-} LightColor;
-
-typedef struct ApplicationState {
-    ApplicationMode mode;
-    LightColor color;
-    bool light_on;
-    bool beep;
-    uint8_t wake_count;
-    bool enter_sleep_mode;
-} ApplicationState;
-
-ApplicationState application_state;
-
-
-//////////////////////////////////////////////////////////////////////////////////////////
-// This section defines the callbacks for our button press events (implemented at bottom).
-// Add any other callbacks you may need either here or in another file.
-void cb_light_pressed();
-void cb_mode_pressed();
-void cb_alarm_pressed();
-
-
-//////////////////////////////////////////////////////////////////////////////////////////
-// This section contains the required functions for any watch app. You should tear out
-// all the code in these functions when writing your app, but you must implement all
-// of the functions, even if they are empty stubs. You can also replace the documentation
-// lines with documentation that describes what your functions do!
-
-/**
- * @brief the app_init function is called before anything else. Use it to set up any
- * internal data structures or application state required by your app.
- */
-void app_init() {
-    memset(&application_state, 0, sizeof(application_state));
-}
-
-/**
- * @brief the app_wake_from_backup function is only called if your app is waking from
- * the ultra-low power BACKUP sleep mode. You may have chosen to store some state in the
- * RTC's backup registers prior to entering this mode. You may restore that state here.
- *
- * @see watch_enter_deep_sleep()
- */
-void app_wake_from_backup() {
-    // This app does not support BACKUP mode.
-}
-
-/**
- * @brief the app_setup function is like setup() in Arduino. It is called once when the
- * program begins. You should set pin modes and enable any peripherals you want to
- * set up (real-time clock, I2C, etc.) Depending on your application, you may or may not
- * want to configure sensors on your sensor board here. For example, a low-power
- * accelerometer that will run at all times should be configured here, whereas you may
- * want to enable a more power-hungry environmental sensor only when you need it.
- *
- * @note If your app enters the Sleep or Deep Sleep modes, this function will be called
- * again on wake, since those modes will have disabled all pins and peripherals; you'll
- * likely need to set them up again. This function will also be called again if your app
- * entered the ultra-low power BACKUP mode, since BACKUP mode will have done all that and
- * also wiped out the system RAM. Note that when this is called after waking from sleep,
- * the RTC will still be configured with the correct date and time.
- */
-void app_setup() {
-    watch_enable_leds();
-    watch_enable_buzzer();
-
-    watch_enable_external_interrupts();
-    // This starter app demonstrates three different ways of using the button interrupts.
-    // The BTN_MODE interrupt only triggers on a rising edge, so the mode changes once per press.
-    watch_register_interrupt_callback(BTN_MODE, cb_mode_pressed, INTERRUPT_TRIGGER_RISING);
-    // The BTN_LIGHT interrupt triggers on both rising and falling edges. The callback then checks
-    // the pin state when triggered: on a button down event, it increments the color and turns the
-    // LED on, whereas on a button up event, it turns the light off.
-    watch_register_interrupt_callback(BTN_LIGHT, cb_light_pressed, INTERRUPT_TRIGGER_BOTH);
-    // The BTN_ALARM callback is on an external wake pin; we can avoid using the EIC for this pin
-    // by using the extwake interrupt — but note that it can only trigger on either a rising or
-    // a falling edge, not both.
-    watch_register_extwake_callback(BTN_ALARM, cb_alarm_pressed, true);
-
-    watch_enable_display();
-}
-
-/**
- * @brief the app_prepare_for_standby function is called before the watch goes into STANDBY mode.
- * In STANDBY mode, most peripherals are shut down, and no code will run until the watch receives
- * an interrupt (generally either the 1Hz tick or a press on one of the buttons).
- */
-void app_prepare_for_standby() {
-}
-
-/**
- * @brief the app_wake_from_standby function is called after the watch wakes from STANDBY mode,
- * but before your main app_loop.
- */
-void app_wake_from_standby() {
-    application_state.wake_count++;
-}
-
-/**
- * @brief the app_loop function is called once on app startup and then again each time the
- * watch exits STANDBY mode.
- */
-bool app_loop() {
-    if (application_state.beep) {
-        watch_buzzer_play_note(BUZZER_NOTE_C7, 50);
-        application_state.beep = false;
-    }
-
-    // set the LED to a color
-    if (application_state.light_on) {
-        switch (application_state.color) {
-            case COLOR_RED:
-                watch_set_led_red();
-                break;
-            case COLOR_GREEN:
-                watch_set_led_green();
-                break;
-            case COLOR_YELLOW:
-                watch_set_led_yellow();
-                break;
-        }
-    } else {
-        watch_set_led_off();
-    }
-
-    // Display the number of times we've woken up (modulo 32 to fit in 2 digits at top right)
-    char buf[3] = {0};
-    sprintf(buf, "%2d", application_state.wake_count % 32);
-    watch_display_string(buf, 2);
-
-    // display "Hello there" text
-    switch (application_state.mode) {
-        case MODE_HELLO:
-            watch_display_string("Hello", 5);
-            break;
-        case MODE_THERE:
-            watch_display_string("there", 5);
-            break;
-    }
-
-    if (application_state.enter_sleep_mode) {
-        // wait a moment for the user's finger to be off the button
-        delay_ms(250);
-
-        // nap time :)
-        watch_enter_deep_sleep_mode();
-
-        // we just woke up; wait a moment again for the user's finger to be off the button...
-        delay_ms(250);
-
-        // and prevent ourselves from going right back to sleep.
-        application_state.enter_sleep_mode = false;
-
-        // finally, after sleep, return false so that our app loop runs again and updates the display.
-        return false;
-    }
-
-    return true;
-}
-
-
-//////////////////////////////////////////////////////////////////////////////////////////
-// Implementations for our callback functions. Replace these with whatever functionality
-// your app requires.
-void cb_light_pressed() {
-    // always turn the light off when the pin goes low
-    if (watch_get_pin_level(BTN_LIGHT) == 0) {
-        application_state.light_on = false;
-        return;
-    }
-    application_state.color = (application_state.color + 1) % 3;
-    application_state.light_on = true;
-}
-
-void cb_mode_pressed() {
-    application_state.mode = (application_state.mode + 1) % 2;
-    application_state.beep = true;
-}
-
-void cb_alarm_pressed() {
-    application_state.enter_sleep_mode = true;
-}
diff --git a/apps/Sensor Watch Starter Project/make/.gitignore b/apps/Sensor Watch Starter Project/make/.gitignore
deleted file mode 100755
index 3722ac63..00000000
--- a/apps/Sensor Watch Starter Project/make/.gitignore
+++ /dev/null
@@ -1 +0,0 @@
-build/

diff --git a/apps/Sensor Watch Starter Project/make/Makefile b/apps/Sensor Watch Starter Project/make/Makefile
deleted file mode 100755
index 09a59a05..00000000
--- a/apps/Sensor Watch Starter Project/make/Makefile
+++ /dev/null
@@ -1,26 +0,0 @@
-# Leave these lines at the top of the file.
-# TOP should get us to the root of the project...
-TOP = ../../..
-# ...and make.mk has all the watch library sources and includes.
-include $(TOP)/make.mk
-
-# If you add any other subdirectories with header files you wish to include, add them after ../
-# Note that you will need to add a backslash at the end of any line you wish to continue, i.e.
-# INCLUDES += \
-#   -I../ \
-#   -I../drivers/ \
-#   -I../utils/
-INCLUDES += \
-  -I../ \
-
-# If you add any other source files you wish to compile, add them after ../app.c
-# Note that you will need to add a backslash at the end of any line you wish to continue, i.e.
-# SRCS += \
-#   ../app.c \
-#   ../drivers/bmp280.c \
-#   ../utils/temperature.c
-SRCS += \
-  ../app.c \
-
-# Leave this line at the bottom of the file; rules.mk has all the targets for making your project.
-include $(TOP)/rules.mk