1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
|
From 120357ea176e420d313cf8cf2ff35fbe233d3bab Mon Sep 17 00:00:00 2001
From: Uenal Mutlu <um@mutluit.com>
Date: Mon, 13 May 2019 16:24:10 +0200
Subject: [PATCH] drivers: ata: ahci_sunxi: Increased SATA/AHCI DMA TX/RX FIFOs
Increasing the SATA/AHCI DMA TX/RX FIFOs (P0DMACR.TXTS and .RXTS, ie.
TX_TRANSACTION_SIZE and RX_TRANSACTION_SIZE) from default 0x0 each
to 0x3 each, gives a write performance boost of 120 MiB/s to 132 MiB/s
from lame 36 MiB/s to 45 MiB/s previously.
Read performance is above 200 MiB/s.
[tested on SSD using dd bs=4K/8K/12K/16K/20K/24K/32K: peak-perf at 12K]
Tested on the SBCs Banana Pi R1 (aka Lamobo R1) and Banana Pi M1 which
are based on the Allwinner A20 32bit-SoC (ARMv7-a / arm-linux-gnueabihf).
These devices are RaspberryPi-like small devices.
This problem of slow SATA write-speed with these small devices lasts
for about 7 years now (beginning with the A10 SoC). Many commentators
throughout the years wrongly assumed the slow write speed was a
hardware limitation. This patch finally solves the problem, which
in fact was just a hard-to-find software problem due to lack of
SATA/AHCI documentation by the SoC-maker Allwinner Technology.
Lists of the affected sunxi and other boards and SoCs with SATA using
the ahci_sunxi driver:
$ grep -i -e "^&ahci" arch/arm/boot/dts/sun*dts
and http://linux-sunxi.org/SATA#Devices_with_SATA_ports
See also http://linux-sunxi.org/Category:Devices_with_SATA_port
Tested-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Uenal Mutlu <um@mutluit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
---
drivers/ata/ahci_sunxi.c | 47 ++++++++++++++++++++++++++++++++++++++--
1 file changed, 45 insertions(+), 2 deletions(-)
--- a/drivers/ata/ahci_sunxi.c
+++ b/drivers/ata/ahci_sunxi.c
@@ -157,8 +157,51 @@ static void ahci_sunxi_start_engine(stru
void __iomem *port_mmio = ahci_port_base(ap);
struct ahci_host_priv *hpriv = ap->host->private_data;
- /* Setup DMA before DMA start */
- sunxi_clrsetbits(hpriv->mmio + AHCI_P0DMACR, 0x0000ff00, 0x00004400);
+ /* Setup DMA before DMA start
+ *
+ * NOTE: A similar SoC with SATA/AHCI by Texas Instruments documents
+ * this Vendor Specific Port (P0DMACR, aka PxDMACR) in its
+ * User's Guide document (TMS320C674x/OMAP-L1x Processor
+ * Serial ATA (SATA) Controller, Literature Number: SPRUGJ8C,
+ * March 2011, Chapter 4.33 Port DMA Control Register (P0DMACR),
+ * p.68, https://www.ti.com/lit/ug/sprugj8c/sprugj8c.pdf)
+ * as equivalent to the following struct:
+ *
+ * struct AHCI_P0DMACR_t
+ * {
+ * unsigned TXTS : 4;
+ * unsigned RXTS : 4;
+ * unsigned TXABL : 4;
+ * unsigned RXABL : 4;
+ * unsigned Reserved : 16;
+ * };
+ *
+ * TXTS: Transmit Transaction Size (TX_TRANSACTION_SIZE).
+ * This field defines the DMA transaction size in DWORDs for
+ * transmit (system bus read, device write) operation. [...]
+ *
+ * RXTS: Receive Transaction Size (RX_TRANSACTION_SIZE).
+ * This field defines the Port DMA transaction size in DWORDs
+ * for receive (system bus write, device read) operation. [...]
+ *
+ * TXABL: Transmit Burst Limit.
+ * This field allows software to limit the VBUSP master read
+ * burst size. [...]
+ *
+ * RXABL: Receive Burst Limit.
+ * Allows software to limit the VBUSP master write burst
+ * size. [...]
+ *
+ * Reserved: Reserved.
+ *
+ *
+ * NOTE: According to the above document, the following alternative
+ * to the code below could perhaps be a better option
+ * (or preparation) for possible further improvements later:
+ * sunxi_clrsetbits(hpriv->mmio + AHCI_P0DMACR, 0x0000ffff,
+ * 0x00000033);
+ */
+ sunxi_clrsetbits(hpriv->mmio + AHCI_P0DMACR, 0x0000ffff, 0x00004433);
/* Start DMA */
sunxi_setbits(port_mmio + PORT_CMD, PORT_CMD_START);
|
