1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
|
--- a/arch/arm/boot/dts/kirkwood-linksys-viper.dts
+++ b/arch/arm/boot/dts/kirkwood-linksys-viper.dts
@@ -67,9 +67,23 @@
};
};
- dsa {
- status = "disabled";
+ switches {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mvsw61xx@10 {
+ compatible = "marvell,88e6171";
+ status = "okay";
+ reg = <0x10>;
+
+ mii-bus = <&mdio>;
+ cpu-port-0 = <5>;
+ cpu-port-1 = <6>;
+ is-indirect;
+ };
+ };
+ dsa {
compatible = "marvell,dsa";
#address-cells = <2>;
#size-cells = <0>;
@@ -161,22 +175,22 @@
};
partition@200000 {
- label = "kernel";
+ label = "kernel1";
reg = <0x200000 0x2A0000>;
};
partition@4a0000 {
- label = "rootfs";
+ label = "rootfs1";
reg = <0x4A0000 0x1760000>;
};
partition@1c00000 {
- label = "alt_kernel";
+ label = "kernel2";
reg = <0x1C00000 0x2A0000>;
};
partition@1ea0000 {
- label = "alt_rootfs";
+ label = "rootfs2";
reg = <0x1EA0000 0x1760000>;
};
@@ -207,53 +221,6 @@
&mdio {
status = "okay";
-
- switch@10 {
- compatible = "marvell,mv88e6085";
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <16>;
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- reg = <0>;
- label = "ethernet1";
- };
-
- port@1 {
- reg = <1>;
- label = "ethernet2";
- };
-
- port@2 {
- reg = <2>;
- label = "ethernet3";
- };
-
- port@3 {
- reg = <3>;
- label = "ethernet4";
- };
-
- port@4 {
- reg = <4>;
- label = "internet";
- };
-
- port@5 {
- reg = <5>;
- label = "cpu";
- ethernet = <ð0port>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
- };
};
&uart0 {
@@ -272,10 +239,14 @@
};
/* eth1 is connected to the switch at port 6. However DSA only supports a
- * single CPU port. So leave this port disabled to avoid confusion.
+ * single CPU port. Upstream uses DSA so they disable this port to avoid confusion.
*/
ð1 {
- status = "disabled";
+ status = "okay";
+ ethernet1-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
};
/* There is no battery on the board, so the RTC does not keep
|
