1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
From 74631102645df8984acbdf67b731e4d437f27fed Mon Sep 17 00:00:00 2001
From: Linus Walleij <linus.walleij@linaro.org>
Date: Thu, 11 Oct 2018 20:06:23 +0200
Subject: [PATCH 08/18] ARM: dts: Enable Gemini flash access
Some Gemini platforms have a parallel NOR flash which conflicts
with use cases reusing some of the flash lines (such as CE1)
for GPIO.
Fix this on the D-Link DIR-685 and Itian SQ201 by creating
"enabled" and "disabled" states for the flash pin control
handle, and rely on the flash handling code to switch this
in and out when accessed so these lines can be used
for GPIO when flash is not accessed, and enable flash
access.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/gemini-dlink-dir-685.dts | 35 +++++++++++++++-------
arch/arm/boot/dts/gemini-sq201.dts | 31 ++++++++++---------
2 files changed, 41 insertions(+), 25 deletions(-)
--- a/arch/arm/boot/dts/gemini-dlink-dir-685.dts
+++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts
@@ -64,7 +64,6 @@
gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>;
gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>;
gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>;
- /* Collides with pflash CE1, not so cool */
cs-gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
num-chipselects = <1>;
@@ -253,15 +252,18 @@
soc {
flash@30000000 {
/*
- * Flash access is by default disabled, because it
- * collides with the Chip Enable signal for the display
- * panel, that reuse the parallel flash Chip Select 1
- * (CS1). Enabling flash makes graphics stop working.
- *
- * We might be able to hack around this by letting
- * GPIO poke around in the flash controller registers.
+ * Flash access collides with the Chip Enable signal for
+ * the display panel, that reuse the parallel flash Chip
+ * Select 1 (CS1). We switch the pin control state so we
+ * enable these pins for flash access only when we need
+ * then, and when disabled they can be used for GPIO which
+ * is what the display panel needs.
*/
- /* status = "okay"; */
+ status = "okay";
+ pinctrl-names = "enabled", "disabled";
+ pinctrl-0 = <&pflash_default_pins>;
+ pinctrl-1 = <&pflash_disabled_pins>;
+
/* 32MB of flash */
reg = <0x30000000 0x02000000>;
@@ -327,7 +329,6 @@
"gpio0cgrp",
"gpio0egrp",
"gpio0fgrp",
- "gpio0ggrp",
"gpio0hgrp";
};
};
@@ -342,6 +343,18 @@
groups = "gpio1bgrp";
};
};
+ /*
+ * These GPIO groups will be mapped in over some
+ * of the flash pins when the flash is not in
+ * active use.
+ */
+ pflash_disabled_pins: pinctrl-pflash-disabled {
+ mux {
+ function = "gpio0";
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+ "gpio0kgrp";
+ };
+ };
pinctrl-gmii {
mux {
function = "gmii";
@@ -430,7 +443,7 @@
};
display-controller@6a000000 {
- status = "okay";
+ status = "disabled";
port@0 {
reg = <0>;
--- a/arch/arm/boot/dts/gemini-sq201.dts
+++ b/arch/arm/boot/dts/gemini-sq201.dts
@@ -41,14 +41,12 @@
compatible = "gpio-leds";
led-green-info {
label = "sq201:green:info";
- /* Conflict with parallel flash */
gpios = <&gpio0 20 GPIO_ACTIVE_HIGH>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
led-green-usb {
label = "sq201:green:usb";
- /* Conflict with parallel and NAND flash */
gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
default-state = "off";
linux,default-trigger = "usb-host";
@@ -126,15 +124,10 @@
soc {
flash@30000000 {
- /*
- * Flash access can be enabled, with the side effect
- * of disabling access to GPIO LED on GPIO0[20] which
- * reuse one of the parallel flash chip select lines.
- * Also the default firmware on the machine has the
- * problem that since it uses the flash, the two LEDS
- * on the right become numb.
- */
- /* status = "okay"; */
+ status = "okay";
+ pinctrl-names = "enabled", "disabled";
+ pinctrl-0 = <&pflash_default_pins>;
+ pinctrl-1 = <&pflash_disabled_pins>;
/* 16MB of flash */
reg = <0x30000000 0x01000000>;
@@ -184,9 +177,7 @@
mux {
function = "gpio0";
groups = "gpio0fgrp",
- "gpio0ggrp",
- "gpio0hgrp",
- "gpio0kgrp";
+ "gpio0hgrp";
};
};
/*
@@ -199,6 +190,18 @@
groups = "gpio1dgrp";
};
};
+ /*
+ * These GPIO groups will be mapped in over some
+ * of the flash pins when the flash is not in
+ * active use.
+ */
+ pflash_disabled_pins: pinctrl-pflash-disabled {
+ mux {
+ function = "gpio0";
+ groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp",
+ "gpio0kgrp";
+ };
+ };
pinctrl-gmii {
mux {
function = "gmii";
|
