1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
|
Index: linux-2.6.25/drivers/usb/host/ohci-ssb.c
===================================================================
--- linux-2.6.25.orig/drivers/usb/host/ohci-ssb.c 2008-04-26 21:56:21.000000000 +0100
+++ linux-2.6.25/drivers/usb/host/ohci-ssb.c 2008-04-26 22:07:53.000000000 +0100
@@ -142,10 +142,59 @@ static int ssb_ohci_attach(struct ssb_de
int err = -ENOMEM;
u32 tmp, flags = 0;
- if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV)
+ /*
+ * THE FOLLOWING COMMENTS PRESERVED FROM GPL SOURCE RELEASE
+ *
+ * The USB core requires a special bit to be set during core
+ * reset to enable host (OHCI) mode. Resetting the SB core in
+ * pcibios_enable_device() is a hack for compatibility with
+ * vanilla usb-ohci so that it does not have to know about
+ * SB. A driver that wants to use the USB core in device mode
+ * should know about SB and should reset the bit back to 0
+ * after calling pcibios_enable_device().
+ */
+
+ if (dev->id.coreid == SSB_DEV_USB11_HOSTDEV) {
flags |= SSB_OHCI_TMSLOW_HOSTMODE;
+ ssb_device_enable(dev, flags);
+ }
+
+ /*
+ * USB 2.0 special considerations:
+ *
+ * 1. Since the core supports both OHCI and EHCI functions, it must
+ * only be reset once.
+ *
+ * 2. In addition to the standard SB reset sequence, the Host Control
+ * Register must be programmed to bring the USB core and various
+ * phy components out of reset.
+ */
+
+ else if (dev->id.coreid == SSB_DEV_USB20_HOST) {
+#warning FIX ME need test for core being up & exit
+ ssb_device_enable(dev, 0);
+ ssb_write32(dev, 0x200, 0x7ff);
+ udelay(1);
+ if (dev->id.revision == 1) { // bug in rev 1
+
+ /* Change Flush control reg */
+ tmp = ssb_read32(dev, 0x400);
+ tmp &= ~8;
+ ssb_write32(dev, 0x400, tmp);
+ tmp = ssb_read32(dev, 0x400);
+ printk("USB20H fcr: 0x%0x\n", tmp);
+
+ /* Change Shim control reg */
+ tmp = ssb_read32(dev, 0x304);
+ tmp &= ~0x100;
+ ssb_write32(dev, 0x304, tmp);
+ tmp = ssb_read32(dev, 0x304);
+ printk("USB20H shim: 0x%0x\n", tmp);
+ }
+ }
+ else
+ ssb_device_enable(dev, 0);
- ssb_device_enable(dev, flags);
hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev,
dev->dev->bus_id);
@@ -235,6 +284,7 @@ static int ssb_ohci_resume(struct ssb_de
static const struct ssb_device_id ssb_ohci_table[] = {
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOSTDEV, SSB_ANY_REV),
SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB11_HOST, SSB_ANY_REV),
+ SSB_DEVICE(SSB_VENDOR_BROADCOM, SSB_DEV_USB20_HOST, SSB_ANY_REV),
SSB_DEVTABLE_END
};
MODULE_DEVICE_TABLE(ssb, ssb_ohci_table);
|
