1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
|
From 11e5c941ff3d09701e57d26b068f634fae29265c Mon Sep 17 00:00:00 2001
From: Erik Sejr <erik@eriks.ssimicro.com>
Date: Tue, 7 Jun 2016 20:58:17 -0400
Subject: [PATCH 381/381] Add ads1015 overlay
See: https://github.com/raspberrypi/linux/pull/1520
---
arch/arm/boot/dts/overlays/Makefile | 1 +
arch/arm/boot/dts/overlays/README | 22 ++++++
arch/arm/boot/dts/overlays/ads1015-overlay.dts | 98 ++++++++++++++++++++++++++
3 files changed, 121 insertions(+)
create mode 100644 arch/arm/boot/dts/overlays/ads1015-overlay.dts
--- a/arch/arm/boot/dts/overlays/Makefile
+++ b/arch/arm/boot/dts/overlays/Makefile
@@ -13,6 +13,7 @@ ifeq ($(CONFIG_ARCH_BCM2835),y)
endif
dtbo-$(RPI_DT_OVERLAYS) += adau1977-adc.dtbo
+dtbo-$(RPI_DT_OVERLAYS) += ads1015.dtbo
dtbo-$(RPI_DT_OVERLAYS) += ads7846.dtbo
dtbo-$(RPI_DT_OVERLAYS) += akkordion-iqdacplus.dtbo
dtbo-$(RPI_DT_OVERLAYS) += at86rf233.dtbo
--- a/arch/arm/boot/dts/overlays/README
+++ b/arch/arm/boot/dts/overlays/README
@@ -168,6 +168,28 @@ Load: dtoverlay=adau1977-adc
Params: <None>
+Name: ads1015
+Info: Overlay for activation of Texas Instruments ADS1015 ADC over I2C
+Load: dtoverlay=ads1015,<param>=<val>
+Params: addr I2C bus address of device. Set based on how the
+ addr pin is wired. (default=0x48 assumes addr
+ is pulled to GND)
+ cha_enable Enable virtual channel a. (default=true)
+ cha_cfg Set the configuration for virtual channel a.
+ (default=4 configures this channel for the
+ voltage at A0 with respect to GND)
+ cha_datarate Set the datarate (samples/sec) for this channel.
+ (default=4 sets 1600 sps)
+ cha_gain Set the gain of the Programmable Gain
+ Amplifier for this channel. (default=2 sets the
+ full scale of the channel to 2.048 Volts)
+
+ Channel (ch) parameters can be set for each enabled channel.
+ A maximum of 4 channels can be enabled (letters a thru d).
+ For more information refer to the device datasheet at:
+ http://www.ti.com/lit/ds/symlink/ads1015.pdf
+
+
Name: ads7846
Info: ADS7846 Touch controller
Load: dtoverlay=ads7846,<param>=<val>
--- /dev/null
+++ b/arch/arm/boot/dts/overlays/ads1015-overlay.dts
@@ -0,0 +1,98 @@
+/*
+ * 2016 - Erik Sejr
+ */
+/dts-v1/;
+/plugin/;
+
+/ {
+ compatible = "brcm,bcm2708";
+ /* ----------- ADS1015 ------------ */
+ fragment@0 {
+ target = <&i2c_arm>;
+ __overlay__ {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+ ads1015: ads1015 {
+ compatible = "ti,ads1015";
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x48>;
+ };
+ };
+ };
+
+ fragment@1 {
+ target-path = "i2c_arm/ads1015";
+ __overlay__ {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ channel_a: channel_a {
+ reg = <4>;
+ ti,gain = <2>;
+ ti,datarate = <4>;
+ };
+ };
+ };
+
+ fragment@2 {
+ target-path = "i2c_arm/ads1015";
+ __dormant__ {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ channel_b: channel_b {
+ reg = <5>;
+ ti,gain = <2>;
+ ti,datarate = <4>;
+ };
+ };
+ };
+
+ fragment@3 {
+ target-path = "i2c_arm/ads1015";
+ __dormant__ {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ channel_c: channel_c {
+ reg = <6>;
+ ti,gain = <2>;
+ ti,datarate = <4>;
+ };
+ };
+ };
+
+ fragment@4 {
+ target-path = "i2c_arm/ads1015";
+ __dormant__ {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ channel_d: channel_d {
+ reg = <7>;
+ ti,gain = <2>;
+ ti,datarate = <4>;
+ };
+ };
+ };
+
+ __overrides__ {
+ addr = <&ads1015>,"reg:0";
+ cha_enable = <0>,"=1";
+ cha_cfg = <&channel_a>,"reg:0";
+ cha_gain = <&channel_a>,"ti,gain:0";
+ cha_datarate = <&channel_a>,"ti,datarate:0";
+ chb_enable = <0>,"=2";
+ chb_cfg = <&channel_b>,"reg:0";
+ chb_gain = <&channel_b>,"ti,gain:0";
+ chb_datarate = <&channel_b>,"ti,datarate:0";
+ chc_enable = <0>,"=3";
+ chc_cfg = <&channel_c>,"reg:0";
+ chc_gain = <&channel_c>,"ti,gain:0";
+ chc_datarate = <&channel_c>,"ti,datarate:0";
+ chd_enable = <0>,"=4";
+ chd_cfg = <&channel_d>,"reg:0";
+ chd_gain = <&channel_d>,"ti,gain:0";
+ chd_datarate = <&channel_d>,"ti,datarate:0";
+ };
+
+};
|
