1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
|
From 8b4d2f080afbd4280ecca0f4b3ceea943a7a86d0 Mon Sep 17 00:00:00 2001
From: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Date: Thu, 23 Mar 2023 11:39:13 +0530
Subject: [PATCH] wifi: ath11k: Optimize 6 GHz scan time
Currently, time taken to scan all supported channels on WCN6750
is ~8 seconds and connection time is almost 10 seconds. WCN6750
supports three Wi-Fi bands (i.e., 2.4/5/6 GHz) and the numbers of
channels for scan come around ~100 channels (default case).
Since the chip doesn't have support for DBS (Dual Band Simultaneous),
scans cannot be parallelized resulting in longer scan times.
Among the 100 odd channels, ~60 channels are in 6 GHz band. Therefore,
optimizing the scan for 6 GHz channels will bring down the overall
scan time.
WCN6750 firmware has support to scan a 6 GHz channel based on co-located
AP information i.e., RNR IE which is found in the legacy 2.4/5 GHz scan
results. When a scan request with all supported channel list is enqueued
to the firmware, then based on WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND
scan channel flag, firmware will scan only those 6 GHz channels for which
RNR IEs are found in the legacy scan results.
In the proposed design, based on NL80211_SCAN_FLAG_COLOCATED_6GHZ scan
flag, driver will set the WMI_SCAN_CHAN_FLAG_SCAN_ONLY_IF_RNR_FOUND flag
for non-PSC channels. Since there is high probability to find 6 GHz APs
on PSC channels, these channels are always scanned. Only non-PSC channels
are selectively scanned based on cached RNR information from the legacy
scan results.
If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set in the scan flags,
then scan will happen on all supported channels (default behavior).
With these optimizations, scan time is improved by 1.5-1.8 seconds on
WCN6750. Similar savings have been observed on WCN6855.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.16
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230323060913.10097-1-quic_mpubbise@quicinc.com
---
drivers/net/wireless/ath/ath11k/mac.c | 25 +++++++++++++++++++++++--
drivers/net/wireless/ath/ath11k/wmi.h | 4 ++++
2 files changed, 27 insertions(+), 2 deletions(-)
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -3819,8 +3819,29 @@ static int ath11k_mac_op_hw_scan(struct
goto exit;
}
- for (i = 0; i < arg->num_chan; i++)
- arg->chan_list[i] = req->channels[i]->center_freq;
+ for (i = 0; i < arg->num_chan; i++) {
+ if (test_bit(WMI_TLV_SERVICE_SCAN_CONFIG_PER_CHANNEL,
+ ar->ab->wmi_ab.svc_map)) {
+ arg->chan_list[i] =
+ u32_encode_bits(req->channels[i]->center_freq,
+ WMI_SCAN_CONFIG_PER_CHANNEL_MASK);
+
+ /* If NL80211_SCAN_FLAG_COLOCATED_6GHZ is set in scan
+ * flags, then scan all PSC channels in 6 GHz band and
+ * those non-PSC channels where RNR IE is found during
+ * the legacy 2.4/5 GHz scan.
+ * If NL80211_SCAN_FLAG_COLOCATED_6GHZ is not set,
+ * then all channels in 6 GHz will be scanned.
+ */
+ if (req->channels[i]->band == NL80211_BAND_6GHZ &&
+ req->flags & NL80211_SCAN_FLAG_COLOCATED_6GHZ &&
+ !cfg80211_channel_is_psc(req->channels[i]))
+ arg->chan_list[i] |=
+ WMI_SCAN_CH_FLAG_SCAN_ONLY_IF_RNR_FOUND;
+ } else {
+ arg->chan_list[i] = req->channels[i]->center_freq;
+ }
+ }
}
if (req->flags & NL80211_SCAN_FLAG_RANDOM_ADDR) {
--- a/drivers/net/wireless/ath/ath11k/wmi.h
+++ b/drivers/net/wireless/ath/ath11k/wmi.h
@@ -2100,6 +2100,7 @@ enum wmi_tlv_service {
/* The second 128 bits */
WMI_MAX_EXT_SERVICE = 256,
+ WMI_TLV_SERVICE_SCAN_CONFIG_PER_CHANNEL = 265,
WMI_TLV_SERVICE_REG_CC_EXT_EVENT_SUPPORT = 281,
WMI_TLV_SERVICE_BIOS_SAR_SUPPORT = 326,
@@ -3249,6 +3250,9 @@ struct wmi_start_scan_cmd {
#define WMI_SCAN_DWELL_MODE_SHIFT 21
#define WMI_SCAN_FLAG_EXT_PASSIVE_SCAN_START_TIME_ENHANCE 0x00000800
+#define WMI_SCAN_CONFIG_PER_CHANNEL_MASK GENMASK(19, 0)
+#define WMI_SCAN_CH_FLAG_SCAN_ONLY_IF_RNR_FOUND BIT(20)
+
enum {
WMI_SCAN_DWELL_MODE_DEFAULT = 0,
WMI_SCAN_DWELL_MODE_CONSERVATIVE = 1,
|
