From add2d65962977caf23ca2fa21a2457d31b636574 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Marek=20Beh=C3=BAn?= Date: Mon, 16 Nov 2020 13:24:22 +0100 Subject: ARM: dts: turris-omnia: add SFP node MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Turris Omnia has an SFP cage that, together with WAN PHY, is connected to eth2 SerDes via a SerDes multiplexor. When a SFP module is present, the multiplexor switches the SerDes signal from PHY to SFP. Describe the SFP cage, but leave it disabled. Until phylink has support for such configuration, we are leaving it to U-Boot to enable SFP and disable WAN PHY at boot time depending on whether a SFP module is present. Signed-off-by: Marek Behún Fixes: 26ca8b52d6e1 ("ARM: dts: add support for Turris Omnia") Reviewed-by: Andrew Lunn Cc: Russell King - ARM Linux admin Cc: linux-arm-kernel@lists.infradead.org Cc: Uwe Kleine-König Cc: Jason Cooper Cc: Gregory CLEMENT Cc: Andreas Färber Cc: Rob Herring Cc: devicetree@vger.kernel.org Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/armada-385-turris-omnia.dts | 30 ++++++++++++++++++++++++++- 1 file changed, 29 insertions(+), 1 deletion(-) --- a/arch/arm/boot/dts/armada-385-turris-omnia.dts +++ b/arch/arm/boot/dts/armada-385-turris-omnia.dts @@ -82,6 +82,24 @@ }; }; }; + + sfp: sfp { + compatible = "sff,sfp"; + i2c-bus = <&sfp_i2c>; + tx-fault-gpios = <&pcawan 0 GPIO_ACTIVE_HIGH>; + tx-disable-gpios = <&pcawan 1 GPIO_ACTIVE_HIGH>; + rate-select0-gpios = <&pcawan 2 GPIO_ACTIVE_HIGH>; + los-gpios = <&pcawan 3 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&pcawan 4 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <3000>; + + /* + * For now this has to be enabled at boot time by U-Boot when + * a SFP module is present. Read more in the comment in the + * eth2 node below. + */ + status = "disabled"; + }; }; &bm { @@ -126,10 +144,20 @@ /* WAN port */ ð2 { + /* + * eth2 is connected via a multiplexor to both the SFP cage and to + * ethernet-phy@1. The multiplexor switches the signal to SFP cage when + * a SFP module is present, as determined by the mode-def0 GPIO. + * + * Until kernel supports this configuration properly, in case SFP module + * is present, U-Boot has to enable the sfp node above, remove phy + * handle and add managed = "in-band-status" property. + */ status = "okay"; phy-mode = "sgmii"; phy = <&phy1>; phys = <&comphy5 2>; + sfp = <&sfp>; buffer-manager = <&bm>; bm,pool-long = <2>; bm,pool-short = <3>; @@ -195,7 +223,7 @@ /* routed to PCIe2 connector (CN62A) */ }; - i2c@4 { + sfp_i2c: i2c@4 { #address-cells = <1>; #size-cells = <0>; reg = <4>;