From 5fc74dbdf8f640a7ca7fb92345ac6fbeaa078d65 Mon Sep 17 00:00:00 2001 From: Pawel Dembicki Date: Tue, 15 Feb 2022 17:39:22 +0100 Subject: [PATCH] ARM: dts: kirkwood: Add Ctera C-200 V1 board Ctera C200 V1 is kirkwood-based 2-Bay NAS. Hardware: - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) - NAND Flash: 256MB (Samsung 216 K9F2G08U0C) - Lan: 1x GBE (Marvell 88E1116R-NNC1) - Storage: 2x SATA HDD 3.5" Slot - USB: 2x USB 2.0 port - Console: Internal J3 connector (1: Vcc, 2: Rx, 3: Tx, 4: GND) - LEDs: 13x GPIO controlled - Buttons: 2x GPIO controlled Signed-off-by: Pawel Dembicki Reviewed-by: Andrew Lunn Signed-off-by: Gregory CLEMENT --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/kirkwood-c200-v1.dts | 310 +++++++++++++++++++++++++ 2 files changed, 311 insertions(+) create mode 100644 arch/arm/boot/dts/kirkwood-c200-v1.dts --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -267,6 +267,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \ dtb-$(CONFIG_MACH_KIRKWOOD) += \ kirkwood-b3.dtb \ kirkwood-blackarmor-nas220.dtb \ + kirkwood-c200-v1.dtb \ kirkwood-cloudbox.dtb \ kirkwood-d2net.dtb \ kirkwood-db-88f6281.dtb \ --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts @@ -0,0 +1,310 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Ctera C200 V1 Board Description + * Copyright 2021-2022 Pawel Dembicki + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include + +/ { + model = "Ctera C200 V1"; + compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + chosen { + bootargs = "console=ttyS0,115200"; + stdout-path = &uart0; + }; + + memory@0 { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&pmx_buttons>; + pinctrl-names = "default"; + + power { + label = "Power Button"; + linux,code = ; + gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; + }; + + reset { + label = "Reset Button"; + linux,code = ; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; + }; + + usb1 { + label = "USB1 Button"; + linux,code = ; + gpios = <&gpio0 28 GPIO_ACTIVE_LOW>; + }; + + usb2 { + label = "USB2 Button"; + linux,code = ; + gpios = <&gpio0 29 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-poweroff { + compatible = "gpio-poweroff"; + pinctrl-0 = <&pmx_poweroff>; + pinctrl-names = "default"; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_leds>; + pinctrl-names = "default"; + + led-0 { + function = LED_FUNCTION_DISK; + function-enumerator = <2>; + color = ; + gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + }; + + led-1 { + function = LED_FUNCTION_DISK; + function-enumerator = <1>; + color = ; + gpios = <&gpio0 15 GPIO_ACTIVE_LOW>; + }; + + led-2 { + function = LED_FUNCTION_DISK; + function-enumerator = <2>; + color = ; + gpios = <&gpio0 16 GPIO_ACTIVE_LOW>; + }; + + led-3 { + function = LED_FUNCTION_DISK; + function-enumerator = <1>; + color = ; + gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; + + led-4 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + + led-5 { + function = LED_FUNCTION_STATUS; + color = ; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + + led-6 { + function = LED_FUNCTION_INDICATOR; + color = ; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + }; + + led-7 { + function = LED_FUNCTION_DISK_ERR; + color = ; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + }; + + led-8 { + function = LED_FUNCTION_DISK_ERR; + color = ; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + }; + + led-9 { + function = LED_FUNCTION_USB; + function-enumerator = <1>; + color = ; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + }; + + led-10 { + function = LED_FUNCTION_USB; + function-enumerator = <1>; + color = ; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "usbport"; + trigger-sources = <&hub_port2>; + }; + + led-11 { + function = LED_FUNCTION_USB; + function-enumerator = <2>; + color = ; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + }; + + led-12 { + function = LED_FUNCTION_USB; + function-enumerator = <2>; + color = ; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + linux,default-trigger = "usbport"; + trigger-sources = <&hub_port1>; + }; + }; +}; + +ð0 { + status = "okay"; +}; + +ð0port { + phy-handle = <ðphy9>; +}; + +&i2c0 { + status = "okay"; + + rtc@30 { + compatible = "s35390a"; + reg = <0x30>; + }; + + lm63@4c { + compatible = "national,lm63"; + reg = <0x4c>; + }; +}; + +&mdio { + status = "okay"; + + ethphy9: ethernet-phy@9 { + reg = <9>; + }; +}; + +&nand { + status = "okay"; + chip-delay = <40>; + + partition@0 { + label = "uboot"; + reg = <0x0000000 0x200000>; + }; + + partition@200000 { + label = "certificate"; + reg = <0x0200000 0x100000>; + }; + + partition@300000 { + label = "preset_cfg"; + reg = <0x0300000 0x100000>; + }; + + partition@400000 { + label = "dev_params"; + reg = <0x0400000 0x100000>; + }; + + partition@500000 { + label = "active_bank"; + reg = <0x0500000 0x0100000>; + }; + + partition@600000 { + label = "magic"; + reg = <0x0600000 0x0100000>; + }; + + partition@700000 { + label = "bank1"; + reg = <0x0700000 0x2800000>; + }; + + partition@2f00000 { + label = "bank2"; + reg = <0x2f00000 0x2800000>; + }; + + /* 0x5700000-0x5a00000 undefined in vendor firmware */ + + partition@5a00000 { + label = "reserved"; + reg = <0x5a00000 0x2000000>; + }; + + partition@7a00000 { + label = "rootfs"; + reg = <0x7a00000 0x8600000>; + }; +}; + +&pinctrl { + /* Buzzer gpios are connected to two pins of buzzer. + * This buzzer require a modulated signal from gpio. + * Leave it as is due lack of proper driver. + */ + pmx_buzzer: pmx-buzzer { + marvell,pins = "mpp12", "mpp13"; + marvell,function = "gpio"; + }; + + pmx_leds: pmx-leds { + marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38", + "mpp39", "mpp40", "mpp42", "mpp43", "mpp44", + "mpp45", "mpp46", "mpp47"; + marvell,function = "gpio"; + }; + + pmx_buttons: pmx-buttons { + marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49"; + marvell,function = "gpio"; + }; + + pmx_poweroff: pmx-poweroff { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; +}; + +&rtc { + status = "disabled"; +}; + +&sata { + status = "okay"; + nr-ports = <2>; +}; + +&uart0 { + status = "okay"; +}; + +&usb0 { + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + + port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + #trigger-source-cells = <0>; + + hub_port1: port@1 { + reg = <1>; + #trigger-source-cells = <0>; + }; + + hub_port2: port@2 { + reg = <2>; + #trigger-source-cells = <0>; + }; + }; +};