/dts-v1/;

#include "kirkwood.dtsi"
#include "kirkwood-6281.dtsi"

/ {
	model = "Seagate GoFlex Home";
	compatible = "seagate,goflexhome", "marvell,kirkwood-88f6281", "marvell,kirkwood";

	aliases {
		led-boot = &led_health;
		led-failsafe = &led_fault;
		led-running = &led_health;
		led-upgrade = &led_fault;
	};

	memory@0 {
		device_type = "memory";
		reg = <0x00000000 0x8000000>;
	};

	chosen {
		bootargs = "console=ttyS0,115200n8 earlyprintk root=/dev/sda1 rootdelay=10";
		stdout-path = &uart0;
	};

	ocp@f1000000 {
		pinctrl: pin-controller@10000 {
			pmx_usb_power_enable: pmx-usb-power-enable {
				marvell,pins = "mpp29";
				marvell,function = "gpio";
			};

			pmx_led_white: pmx-led-white {
				marvell,pins = "mpp40";
				marvell,function = "gpio";
			};

			pmx_led_green: pmx-led_green {
				marvell,pins = "mpp46";
				marvell,function = "gpio";
			};

			pmx_led_orange: pmx-led-orange {
				marvell,pins = "mpp47";
				marvell,function = "gpio";
			};
		};

		serial@12000 {
			status = "okay";
		};

		sata@80000 {
			status = "okay";
			nr-ports = <2>;
		};
	};

	gpio-leds {
		compatible = "gpio-leds";

		led_health: health {
			label = "status:green:health";
			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
			default-state = "on";
		};

		led_fault: fault {
			label = "status:orange:fault";
			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
		};

		misc {
			label = "status:white:misc";
			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
			linux,default-trigger = "disk-activity";
		};
	};

	regulators {
		compatible = "simple-bus";

		#address-cells = <1>;
		#size-cells = <0>;

		pinctrl-0 = <&pmx_usb_power_enable>;
		pinctrl-names = "default";

		usb_power: regulator@1 {
			compatible = "regulator-fixed";
			reg = <1>;
			regulator-name = "USB Power";
			regulator-min-microvolt = <5000000>;
			regulator-max-microvolt = <5000000>;
			enable-active-high;
			regulator-always-on;
			regulator-boot-on;
			gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
		};
	};
};

&nand {
	status = "okay";

	chip-delay = <40>;

	partition@0 {
		label = "u-boot";
		reg = <0x0000000 0x0100000>;
		read-only;
	};

	partition@100000 {
		label = "ubi";
		reg = <0x0100000 0xff00000>;
	};
};

&mdio {
	status = "okay";

	ethphy0: ethernet-phy@0 {
		reg = <0>;
	};
};

&eth0 {
	status = "okay";

	ethernet0-port@0 {
		phy-handle = <&ethphy0>;
	};
};