From 425015979d3b1600d14403be7d6d64ba1238e58d Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Mon, 14 Apr 2014 22:10:36 -0500 Subject: [PATCH 041/182] dt: Document Qualcomm IPQ8064 pinctrl binding Define a new binding for the Qualcomm TLMMv2 based pin controller inside the IPQ8064. Signed-off-by: Andy Gross Reviewed-by: Bjorn Andersson Signed-off-by: Linus Walleij --- .../bindings/pinctrl/qcom,ipq8064-pinctrl.txt | 95 ++++++++++++++++++++ 1 file changed, 95 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt new file mode 100644 index 0000000..e0d35a4 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq8064-pinctrl.txt @@ -0,0 +1,95 @@ +Qualcomm IPQ8064 TLMM block + +Required properties: +- compatible: "qcom,ipq8064-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Qualcomm's pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength, + output-low, output-high. + +Non-empty subnodes must specify the 'pins' property. + +Valid values for qcom,pins are: + gpio0-gpio68 + Supports mux, bias, and drive-strength + + sdc3_clk, sdc3_cmd, sdc3_data + Supports bias and drive-strength + + +Valid values for function are: + mdio, mi2s, pdm, ssbi, spmi, audio_pcm, gsbi1, gsbi2, gsbi4, gsbi5, + gsbi5_spi_cs1, gsbi5_spi_cs2, gsbi5_spi_cs3, gsbi6, gsbi7, nss_spi, sdc1, + spdif, nand, tsif1, tsif2, usb_fs_n, usb_fs, usb2_hsic, rgmii2, sata, + pcie1_rst, pcie1_prsnt, pcie1_pwren_n, pcie1_pwren, pcie1_pwrflt, + pcie1_clk_req, pcie2_rst, pcie2_prsnt, pcie2_pwren_n, pcie2_pwren, + pcie2_pwrflt, pcie2_clk_req, pcie3_rst, pcie3_prsnt, pcie3_pwren_n, + pcie3_pwren, pcie3_pwrflt, pcie3_clk_req, ps_hold + +Example: + + pinmux: pinctrl@800000 { + compatible = "qcom,ipq8064-pinctrl"; + reg = <0x800000 0x4000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 32 0x4>; + + pinctrl-names = "default"; + pinctrl-0 = <&gsbi5_uart_default>; + + gsbi5_uart_default: gsbi5_uart_default { + mux { + pins = "gpio18", "gpio19"; + function = "gsbi5"; + }; + + tx { + pins = "gpio18"; + drive-strength = <4>; + bias-disable; + }; + + rx { + pins = "gpio19"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; -- 1.7.10.4