commit 152a2a8b5e1d4cbe91a7c66f1028db15164a3766 Author: David Woodhouse Date: Wed Dec 19 11:01:21 2012 +0000 solos-pci: ensure all TX packets are aligned to 4 bytes The FPGA can't handled unaligned DMA (yet). So copy into an aligned buffer, if skb->data isn't suitably aligned. Signed-off-by: David Woodhouse Signed-off-by: David S. Miller commit 13af816469db3449c072afbae6c4c1bd9ccecccb Author: Nathan Williams Date: Wed Dec 19 11:01:20 2012 +0000 solos-pci: add firmware upgrade support for new models Signed-off-by: Nathan Williams Signed-off-by: David Woodhouse Signed-off-by: David S. Miller commit 7fbdadb5e951e4f0c0fc991ff5f50295568786e6 Author: Nathan Williams Date: Wed Dec 19 11:01:19 2012 +0000 solos-pci: remove superfluous debug output Signed-off-by: Nathan Williams Signed-off-by: David Woodhouse Signed-off-by: David S. Miller commit f9baad02e7411d9f38d5ebe1a1cdcde4ceec100d Author: Nathan Williams Date: Wed Dec 19 11:01:18 2012 +0000 solos-pci: add GPIO support for newer versions on Geos board dwmw2: Tidy up a little, simpler matching on which GPIO is being accessed, only register on newer boards, register under PCI device instead of duplicating them under each ATM device. Signed-off-by: Nathan Williams Signed-off-by: David Woodhouse Signed-off-by: David S. Miller commit cae49ede00ec3d0cda290b03fee55b72b49efc11 Author: David Woodhouse Date: Tue Dec 11 14:57:14 2012 +0000 solos-pci: fix double-free of TX skb in DMA mode We weren't clearing card->tx_skb[port] when processing the TX done interrupt. If there wasn't another skb ready to transmit immediately, this led to a double-free because we'd free it *again* next time we did have a packet to send. Signed-off-by: David Woodhouse Cc: stable@kernel.org Signed-off-by: David S. Miller == There is a typo here so we do a double lock instead of an unlock. Signed-off-by: Dan Carpenter --- Only needed in linux-next. Introduced in f9baad02e7411d9 [14/17] solos-pci: add GPIO support for newer versions on Geos board --- a/drivers/atm/solos-pci.c +++ b/drivers/atm/solos-pci.c @@ -42,7 +42,8 @@ #include #include -#define VERSION "0.07" +#define VERSION "1.04" +#define DRIVER_VERSION 0x01 #define PTAG "solos-pci" #define CONFIG_RAM_SIZE 128 @@ -56,16 +57,21 @@ #define FLASH_BUSY 0x60 #define FPGA_MODE 0x5C #define FLASH_MODE 0x58 +#define GPIO_STATUS 0x54 +#define DRIVER_VER 0x50 #define TX_DMA_ADDR(port) (0x40 + (4 * (port))) #define RX_DMA_ADDR(port) (0x30 + (4 * (port))) #define DATA_RAM_SIZE 32768 #define BUF_SIZE 2048 #define OLD_BUF_SIZE 4096 /* For FPGA versions <= 2*/ -#define FPGA_PAGE 528 /* FPGA flash page size*/ -#define SOLOS_PAGE 512 /* Solos flash page size*/ -#define FPGA_BLOCK (FPGA_PAGE * 8) /* FPGA flash block size*/ -#define SOLOS_BLOCK (SOLOS_PAGE * 8) /* Solos flash block size*/ +/* Old boards use ATMEL AD45DB161D flash */ +#define ATMEL_FPGA_PAGE 528 /* FPGA flash page size*/ +#define ATMEL_SOLOS_PAGE 512 /* Solos flash page size*/ +#define ATMEL_FPGA_BLOCK (ATMEL_FPGA_PAGE * 8) /* FPGA block size*/ +#define ATMEL_SOLOS_BLOCK (ATMEL_SOLOS_PAGE * 8) /* Solos block size*/ +/* Current boards use M25P/M25PE SPI flash */ +#define SPI_FLASH_BLOCK (256 * 64) #define RX_BUF(card, nr) ((card->buffers) + (nr)*(card->buffer_size)*2) #define TX_BUF(card, nr) ((card->buffers) + (nr)*(card->buffer_size)*2 + (card->buffer_size)) @@ -123,11 +129,14 @@ struct solos_card { struct sk_buff_head cli_queue[4]; struct sk_buff *tx_skb[4]; struct sk_buff *rx_skb[4]; + unsigned char *dma_bounce; wait_queue_head_t param_wq; wait_queue_head_t fw_wq; int using_dma; + int dma_alignment; int fpga_version; int buffer_size; + int atmel_flash; }; @@ -452,7 +461,6 @@ static ssize_t console_show(struct devic len = skb->len; memcpy(buf, skb->data, len); - dev_dbg(&card->dev->dev, "len: %d\n", len); kfree_skb(skb); return len; @@ -499,6 +507,78 @@ static ssize_t console_store(struct devi return err?:count; } +struct geos_gpio_attr { + struct device_attribute attr; + int offset; +}; + +#define SOLOS_GPIO_ATTR(_name, _mode, _show, _store, _offset) \ + struct geos_gpio_attr gpio_attr_##_name = { \ + .attr = __ATTR(_name, _mode, _show, _store), \ + .offset = _offset } + +static ssize_t geos_gpio_store(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct pci_dev *pdev = container_of(dev, struct pci_dev, dev); + struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr); + struct solos_card *card = pci_get_drvdata(pdev); + uint32_t data32; + + if (count != 1 && (count != 2 || buf[1] != '\n')) + return -EINVAL; + + spin_lock_irq(&card->param_queue_lock); + data32 = ioread32(card->config_regs + GPIO_STATUS); + if (buf[0] == '1') { + data32 |= 1 << gattr->offset; + iowrite32(data32, card->config_regs + GPIO_STATUS); + } else if (buf[0] == '0') { + data32 &= ~(1 << gattr->offset); + iowrite32(data32, card->config_regs + GPIO_STATUS); + } else { + count = -EINVAL; + } + spin_unlock_irq(&card->param_queue_lock); + return count; +} + +static ssize_t geos_gpio_show(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct pci_dev *pdev = container_of(dev, struct pci_dev, dev); + struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr); + struct solos_card *card = pci_get_drvdata(pdev); + uint32_t data32; + + data32 = ioread32(card->config_regs + GPIO_STATUS); + data32 = (data32 >> gattr->offset) & 1; + + return sprintf(buf, "%d\n", data32); +} + +static ssize_t hardware_show(struct device *dev, struct device_attribute *attr, + char *buf) +{ + struct pci_dev *pdev = container_of(dev, struct pci_dev, dev); + struct geos_gpio_attr *gattr = container_of(attr, struct geos_gpio_attr, attr); + struct solos_card *card = pci_get_drvdata(pdev); + uint32_t data32; + + data32 = ioread32(card->config_regs + GPIO_STATUS); + switch (gattr->offset) { + case 0: + /* HardwareVersion */ + data32 = data32 & 0x1F; + break; + case 1: + /* HardwareVariant */ + data32 = (data32 >> 5) & 0x0F; + break; + } + return sprintf(buf, "%d\n", data32); +} + static DEVICE_ATTR(console, 0644, console_show, console_store); @@ -507,6 +587,14 @@ static DEVICE_ATTR(console, 0644, consol #include "solos-attrlist.c" +static SOLOS_GPIO_ATTR(GPIO1, 0644, geos_gpio_show, geos_gpio_store, 9); +static SOLOS_GPIO_ATTR(GPIO2, 0644, geos_gpio_show, geos_gpio_store, 10); +static SOLOS_GPIO_ATTR(GPIO3, 0644, geos_gpio_show, geos_gpio_store, 11); +static SOLOS_GPIO_ATTR(GPIO4, 0644, geos_gpio_show, geos_gpio_store, 12); +static SOLOS_GPIO_ATTR(GPIO5, 0644, geos_gpio_show, geos_gpio_store, 13); +static SOLOS_GPIO_ATTR(PushButton, 0444, geos_gpio_show, NULL, 14); +static SOLOS_GPIO_ATTR(HardwareVersion, 0444, hardware_show, NULL, 0); +static SOLOS_GPIO_ATTR(HardwareVariant, 0444, hardware_show, NULL, 1); #undef SOLOS_ATTR_RO #undef SOLOS_ATTR_RW @@ -523,6 +611,23 @@ static struct attribute_group solos_attr .name = "parameters", }; +static struct attribute *gpio_attrs[] = { + &gpio_attr_GPIO1.attr.attr, + &gpio_attr_GPIO2.attr.attr, + &gpio_attr_GPIO3.attr.attr, + &gpio_attr_GPIO4.attr.attr, + &gpio_attr_GPIO5.attr.attr, + &gpio_attr_PushButton.attr.attr, + &gpio_attr_HardwareVersion.attr.attr, + &gpio_attr_HardwareVariant.attr.attr, + NULL +}; + +static struct attribute_group gpio_attr_group = { + .attrs = gpio_attrs, + .name = "gpio", +}; + static int flash_upgrade(struct solos_card *card, int chip) { const struct firmware *fw; @@ -534,16 +639,25 @@ static int flash_upgrade(struct solos_ca switch (chip) { case 0: fw_name = "solos-FPGA.bin"; - blocksize = FPGA_BLOCK; + if (card->atmel_flash) + blocksize = ATMEL_FPGA_BLOCK; + else + blocksize = SPI_FLASH_BLOCK; break; case 1: fw_name = "solos-Firmware.bin"; - blocksize = SOLOS_BLOCK; + if (card->atmel_flash) + blocksize = ATMEL_SOLOS_BLOCK; + else + blocksize = SPI_FLASH_BLOCK; break; case 2: if (card->fpga_version > LEGACY_BUFFERS){ fw_name = "solos-db-FPGA.bin"; - blocksize = FPGA_BLOCK; + if (card->atmel_flash) + blocksize = ATMEL_FPGA_BLOCK; + else + blocksize = SPI_FLASH_BLOCK; } else { dev_info(&card->dev->dev, "FPGA version doesn't support" " daughter board upgrades\n"); @@ -553,7 +667,10 @@ static int flash_upgrade(struct solos_ca case 3: if (card->fpga_version > LEGACY_BUFFERS){ fw_name = "solos-Firmware.bin"; - blocksize = SOLOS_BLOCK; + if (card->atmel_flash) + blocksize = ATMEL_SOLOS_BLOCK; + else + blocksize = SPI_FLASH_BLOCK; } else { dev_info(&card->dev->dev, "FPGA version doesn't support" " daughter board upgrades\n"); @@ -569,6 +686,9 @@ static int flash_upgrade(struct solos_ca dev_info(&card->dev->dev, "Flash upgrade starting\n"); + /* New FPGAs require driver version before permitting flash upgrades */ + iowrite32(DRIVER_VERSION, card->config_regs + DRIVER_VER); + numblocks = fw->size / blocksize; dev_info(&card->dev->dev, "Firmware size: %zd\n", fw->size); dev_info(&card->dev->dev, "Number of blocks: %d\n", numblocks); @@ -598,9 +718,13 @@ static int flash_upgrade(struct solos_ca /* dev_info(&card->dev->dev, "Set FPGA Flash mode to Block Write\n"); */ iowrite32(((chip * 2) + 1), card->config_regs + FLASH_MODE); - /* Copy block to buffer, swapping each 16 bits */ + /* Copy block to buffer, swapping each 16 bits for Atmel flash */ for(i = 0; i < blocksize; i += 4) { - uint32_t word = swahb32p((uint32_t *)(fw->data + offset + i)); + uint32_t word; + if (card->atmel_flash) + word = swahb32p((uint32_t *)(fw->data + offset + i)); + else + word = *(uint32_t *)(fw->data + offset + i); if(card->fpga_version > LEGACY_BUFFERS) iowrite32(word, FLASH_BUF + i); else @@ -945,10 +1069,11 @@ static uint32_t fpga_tx(struct solos_car for (port = 0; tx_pending; tx_pending >>= 1, port++) { if (tx_pending & 1) { struct sk_buff *oldskb = card->tx_skb[port]; - if (oldskb) + if (oldskb) { pci_unmap_single(card->dev, SKB_CB(oldskb)->dma_addr, oldskb->len, PCI_DMA_TODEVICE); - + card->tx_skb[port] = NULL; + } spin_lock(&card->tx_queue_lock); skb = skb_dequeue(&card->tx_queue[port]); if (!skb) @@ -960,7 +1085,12 @@ static uint32_t fpga_tx(struct solos_car tx_started |= 1 << port; oldskb = skb; /* We're done with this skb already */ } else if (skb && card->using_dma) { - SKB_CB(skb)->dma_addr = pci_map_single(card->dev, skb->data, + unsigned char *data = skb->data; + if ((unsigned long)data & card->dma_alignment) { + data = card->dma_bounce + (BUF_SIZE * port); + memcpy(data, skb->data, skb->len); + } + SKB_CB(skb)->dma_addr = pci_map_single(card->dev, data, skb->len, PCI_DMA_TODEVICE); card->tx_skb[port] = skb; iowrite32(SKB_CB(skb)->dma_addr, @@ -1134,18 +1264,33 @@ static int fpga_probe(struct pci_dev *de db_fpga_upgrade = db_firmware_upgrade = 0; } + /* Stopped using Atmel flash after 0.03-38 */ + if (fpga_ver < 39) + card->atmel_flash = 1; + else + card->atmel_flash = 0; + + data32 = ioread32(card->config_regs + PORTS); + card->nr_ports = (data32 & 0x000000FF); + if (card->fpga_version >= DMA_SUPPORTED) { pci_set_master(dev); card->using_dma = 1; + if (1) { /* All known FPGA versions so far */ + card->dma_alignment = 3; + card->dma_bounce = kmalloc(card->nr_ports * BUF_SIZE, GFP_KERNEL); + if (!card->dma_bounce) { + dev_warn(&card->dev->dev, "Failed to allocate DMA bounce buffers\n"); + /* Fallback to MMIO doesn't work */ + goto out_unmap_both; + } + } } else { card->using_dma = 0; /* Set RX empty flag for all ports */ iowrite32(0xF0, card->config_regs + FLAGS_ADDR); } - data32 = ioread32(card->config_regs + PORTS); - card->nr_ports = (data32 & 0x000000FF); - pci_set_drvdata(dev, card); tasklet_init(&card->tlet, solos_bh, (unsigned long)card); @@ -1180,6 +1325,10 @@ static int fpga_probe(struct pci_dev *de if (err) goto out_free_irq; + if (card->fpga_version >= DMA_SUPPORTED && + sysfs_create_group(&card->dev->dev.kobj, &gpio_attr_group)) + dev_err(&card->dev->dev, "Could not register parameter group for GPIOs\n"); + return 0; out_free_irq: @@ -1188,6 +1337,7 @@ static int fpga_probe(struct pci_dev *de tasklet_kill(&card->tlet); out_unmap_both: + kfree(card->dma_bounce); pci_set_drvdata(dev, NULL); pci_iounmap(dev, card->buffers); out_unmap_config: @@ -1290,11 +1440,16 @@ static void fpga_remove(struct pci_dev * iowrite32(1, card->config_regs + FPGA_MODE); (void)ioread32(card->config_regs + FPGA_MODE); + if (card->fpga_version >= DMA_SUPPORTED) + sysfs_remove_group(&card->dev->dev.kobj, &gpio_attr_group); + atm_remove(card); free_irq(dev->irq, card); tasklet_kill(&card->tlet); + kfree(card->dma_bounce); + /* Release device from reset */ iowrite32(0, card->config_regs + FPGA_MODE); (void)ioread32(card->config_regs + FPGA_MODE);