From aae673201fa2bd432a47654d9bcd9edc872d456f Mon Sep 17 00:00:00 2001 From: Phil Elwell Date: Mon, 5 Oct 2015 10:47:45 +0100 Subject: [PATCH 111/156] BCM270X_DT: Add at86rf233 overlay Add an overlay to support the Atmel AT86RF233 WPAN transceiver on spi0.0. See: https://github.com/raspberrypi/linux/issues/1151 --- arch/arm/boot/dts/overlays/Makefile | 1 + arch/arm/boot/dts/overlays/README | 21 +++++++-- arch/arm/boot/dts/overlays/at86rf233-overlay.dts | 54 ++++++++++++++++++++++++ 3 files changed, 72 insertions(+), 4 deletions(-) create mode 100644 arch/arm/boot/dts/overlays/at86rf233-overlay.dts --- a/arch/arm/boot/dts/overlays/Makefile +++ b/arch/arm/boot/dts/overlays/Makefile @@ -13,6 +13,7 @@ ifeq ($(CONFIG_ARCH_BCM2835),y) endif dtb-$(RPI_DT_OVERLAYS) += ads7846-overlay.dtb +dtb-$(RPI_DT_OVERLAYS) += at86rf233-overlay.dtb dtb-$(RPI_DT_OVERLAYS) += bmp085_i2c-sensor-overlay.dtb dtb-$(RPI_DT_OVERLAYS) += dht11-overlay.dtb dtb-$(RPI_DT_OVERLAYS) += enc28j60-overlay.dtb --- a/arch/arm/boot/dts/overlays/README +++ b/arch/arm/boot/dts/overlays/README @@ -69,13 +69,14 @@ DT parameters: Parameters always have default values, although in some cases (e.g. "w1-gpio") it is necessary to provided multiple overlays in order to get the desired -behaviour. See the list of overlays below for a description of the parameters and their defaults. +behaviour. See the list of overlays below for a description of the parameters +and their defaults. The Overlay and Parameter Reference =================================== -N.B. When editing this file, please preserve the indentation levels to make it simple to parse -programmatically. NO HARD TABS. +N.B. When editing this file, please preserve the indentation levels to make it +simple to parse programmatically. NO HARD TABS. Name: @@ -149,7 +150,7 @@ Name: ads7846 Info: ADS7846 Touch controller Load: dtoverlay=ads7846,= Params: cs SPI bus Chip Select (default 1) - speed SPI bus speed (default 2Mhz, max 3.25MHz) + speed SPI bus speed (default 2MHz, max 3.25MHz) penirq GPIO used for PENIRQ. REQUIRED penirq_pull Set GPIO pull (default 0=none, 2=pullup) swapxy Swap x and y axis @@ -170,6 +171,18 @@ Params: cs SPI bus www.kernel.org/doc/Documentation/devicetree/bindings/input/ads7846.txt +Name: at86rf233 +Info: Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver, + connected to spi0.0 +Load: dtoverlay=at86rf233,= +Params: interrupt GPIO used for INT (default 23) + reset GPIO used for Reset (default 24) + sleep GPIO used for Sleep (default 25) + speed SPI bus speed in Hz (default 6000000) + trim Fine tuning of the internal capacitance + arrays (0=+0pF, 15=+4.5pF, default 15) + + Name: bmp085_i2c-sensor Info: Configures the BMP085/BMP180 digital barometric pressure and temperature sensors from Bosch Sensortec --- /dev/null +++ b/arch/arm/boot/dts/overlays/at86rf233-overlay.dts @@ -0,0 +1,54 @@ +/dts-v1/; +/plugin/; + +/* Overlay for Atmel AT86RF233 IEEE 802.15.4 WPAN transceiver on spi0.0 */ + +/ { + compatible = "brcm,bcm2835", "brcm,bcm2836", "brcm,bcm2708", "brcm,bcm2709"; + + fragment@0 { + target = <&spi0>; + __overlay__ { + #address-cells = <1>; + #size-cells = <0>; + + status = "okay"; + + spidev@0{ + status = "disabled"; + }; + + lowpan0: at86rf233@0 { + compatible = "atmel,at86rf233"; + reg = <0>; + interrupt-parent = <&gpio>; + interrupts = <23 4>; /* active high */ + reset-gpio = <&gpio 24 1>; + sleep-gpio = <&gpio 25 1>; + spi-max-frequency = <6000000>; + xtal-trim = /bits/ 8 <0xf>; + }; + }; + }; + + fragment@1 { + target = <&gpio>; + __overlay__ { + lowpan0_pins: lowpan0_pins { + brcm,pins = <23 24 25>; + brcm,function = <0 1 1>; /* in out out */ + }; + }; + }; + + __overrides__ { + interrupt = <&lowpan0>, "interrupts:0", + <&lowpan0_pins>, "brcm,pins:0"; + reset = <&lowpan0>, "reset-gpio:4", + <&lowpan0_pins>, "brcm,pins:4"; + sleep = <&lowpan0>, "sleep-gpio:4", + <&lowpan0_pins>, "brcm,pins:8"; + speed = <&lowpan0>, "spi-max-frequency:0"; + trim = <&lowpan0>, "xtal-trim.0"; + }; +};