This patches adds the SPI-NOR device support code form kernel 3.17-rc1. This patch does not contain any further code not in this mainline kernel. --- a/drivers/mtd/Kconfig +++ b/drivers/mtd/Kconfig @@ -366,6 +366,8 @@ source "drivers/mtd/onenand/Kconfig" source "drivers/mtd/lpddr/Kconfig" +source "drivers/mtd/spi-nor/Kconfig" + source "drivers/mtd/ubi/Kconfig" endif # MTD --- a/drivers/mtd/Makefile +++ b/drivers/mtd/Makefile @@ -35,4 +35,5 @@ inftl-objs := inftlcore.o inftlmount.o obj-y += chips/ lpddr/ maps/ devices/ nand/ onenand/ tests/ +obj-$(CONFIG_MTD_SPI_NOR) += spi-nor/ obj-$(CONFIG_MTD_UBI) += ubi/ --- /dev/null +++ b/drivers/mtd/spi-nor/fsl-quadspi.c @@ -0,0 +1,1009 @@ +/* + * Freescale QuadSPI driver. + * + * Copyright (C) 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +/* The registers */ +#define QUADSPI_MCR 0x00 +#define QUADSPI_MCR_RESERVED_SHIFT 16 +#define QUADSPI_MCR_RESERVED_MASK (0xF << QUADSPI_MCR_RESERVED_SHIFT) +#define QUADSPI_MCR_MDIS_SHIFT 14 +#define QUADSPI_MCR_MDIS_MASK (1 << QUADSPI_MCR_MDIS_SHIFT) +#define QUADSPI_MCR_CLR_TXF_SHIFT 11 +#define QUADSPI_MCR_CLR_TXF_MASK (1 << QUADSPI_MCR_CLR_TXF_SHIFT) +#define QUADSPI_MCR_CLR_RXF_SHIFT 10 +#define QUADSPI_MCR_CLR_RXF_MASK (1 << QUADSPI_MCR_CLR_RXF_SHIFT) +#define QUADSPI_MCR_DDR_EN_SHIFT 7 +#define QUADSPI_MCR_DDR_EN_MASK (1 << QUADSPI_MCR_DDR_EN_SHIFT) +#define QUADSPI_MCR_END_CFG_SHIFT 2 +#define QUADSPI_MCR_END_CFG_MASK (3 << QUADSPI_MCR_END_CFG_SHIFT) +#define QUADSPI_MCR_SWRSTHD_SHIFT 1 +#define QUADSPI_MCR_SWRSTHD_MASK (1 << QUADSPI_MCR_SWRSTHD_SHIFT) +#define QUADSPI_MCR_SWRSTSD_SHIFT 0 +#define QUADSPI_MCR_SWRSTSD_MASK (1 << QUADSPI_MCR_SWRSTSD_SHIFT) + +#define QUADSPI_IPCR 0x08 +#define QUADSPI_IPCR_SEQID_SHIFT 24 +#define QUADSPI_IPCR_SEQID_MASK (0xF << QUADSPI_IPCR_SEQID_SHIFT) + +#define QUADSPI_BUF0CR 0x10 +#define QUADSPI_BUF1CR 0x14 +#define QUADSPI_BUF2CR 0x18 +#define QUADSPI_BUFXCR_INVALID_MSTRID 0xe + +#define QUADSPI_BUF3CR 0x1c +#define QUADSPI_BUF3CR_ALLMST_SHIFT 31 +#define QUADSPI_BUF3CR_ALLMST (1 << QUADSPI_BUF3CR_ALLMST_SHIFT) + +#define QUADSPI_BFGENCR 0x20 +#define QUADSPI_BFGENCR_PAR_EN_SHIFT 16 +#define QUADSPI_BFGENCR_PAR_EN_MASK (1 << (QUADSPI_BFGENCR_PAR_EN_SHIFT)) +#define QUADSPI_BFGENCR_SEQID_SHIFT 12 +#define QUADSPI_BFGENCR_SEQID_MASK (0xF << QUADSPI_BFGENCR_SEQID_SHIFT) + +#define QUADSPI_BUF0IND 0x30 +#define QUADSPI_BUF1IND 0x34 +#define QUADSPI_BUF2IND 0x38 +#define QUADSPI_SFAR 0x100 + +#define QUADSPI_SMPR 0x108 +#define QUADSPI_SMPR_DDRSMP_SHIFT 16 +#define QUADSPI_SMPR_DDRSMP_MASK (7 << QUADSPI_SMPR_DDRSMP_SHIFT) +#define QUADSPI_SMPR_FSDLY_SHIFT 6 +#define QUADSPI_SMPR_FSDLY_MASK (1 << QUADSPI_SMPR_FSDLY_SHIFT) +#define QUADSPI_SMPR_FSPHS_SHIFT 5 +#define QUADSPI_SMPR_FSPHS_MASK (1 << QUADSPI_SMPR_FSPHS_SHIFT) +#define QUADSPI_SMPR_HSENA_SHIFT 0 +#define QUADSPI_SMPR_HSENA_MASK (1 << QUADSPI_SMPR_HSENA_SHIFT) + +#define QUADSPI_RBSR 0x10c +#define QUADSPI_RBSR_RDBFL_SHIFT 8 +#define QUADSPI_RBSR_RDBFL_MASK (0x3F << QUADSPI_RBSR_RDBFL_SHIFT) + +#define QUADSPI_RBCT 0x110 +#define QUADSPI_RBCT_WMRK_MASK 0x1F +#define QUADSPI_RBCT_RXBRD_SHIFT 8 +#define QUADSPI_RBCT_RXBRD_USEIPS (0x1 << QUADSPI_RBCT_RXBRD_SHIFT) + +#define QUADSPI_TBSR 0x150 +#define QUADSPI_TBDR 0x154 +#define QUADSPI_SR 0x15c +#define QUADSPI_SR_IP_ACC_SHIFT 1 +#define QUADSPI_SR_IP_ACC_MASK (0x1 << QUADSPI_SR_IP_ACC_SHIFT) +#define QUADSPI_SR_AHB_ACC_SHIFT 2 +#define QUADSPI_SR_AHB_ACC_MASK (0x1 << QUADSPI_SR_AHB_ACC_SHIFT) + +#define QUADSPI_FR 0x160 +#define QUADSPI_FR_TFF_MASK 0x1 + +#define QUADSPI_SFA1AD 0x180 +#define QUADSPI_SFA2AD 0x184 +#define QUADSPI_SFB1AD 0x188 +#define QUADSPI_SFB2AD 0x18c +#define QUADSPI_RBDR 0x200 + +#define QUADSPI_LUTKEY 0x300 +#define QUADSPI_LUTKEY_VALUE 0x5AF05AF0 + +#define QUADSPI_LCKCR 0x304 +#define QUADSPI_LCKER_LOCK 0x1 +#define QUADSPI_LCKER_UNLOCK 0x2 + +#define QUADSPI_RSER 0x164 +#define QUADSPI_RSER_TFIE (0x1 << 0) + +#define QUADSPI_LUT_BASE 0x310 + +/* + * The definition of the LUT register shows below: + * + * --------------------------------------------------- + * | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 | + * --------------------------------------------------- + */ +#define OPRND0_SHIFT 0 +#define PAD0_SHIFT 8 +#define INSTR0_SHIFT 10 +#define OPRND1_SHIFT 16 + +/* Instruction set for the LUT register. */ +#define LUT_STOP 0 +#define LUT_CMD 1 +#define LUT_ADDR 2 +#define LUT_DUMMY 3 +#define LUT_MODE 4 +#define LUT_MODE2 5 +#define LUT_MODE4 6 +#define LUT_READ 7 +#define LUT_WRITE 8 +#define LUT_JMP_ON_CS 9 +#define LUT_ADDR_DDR 10 +#define LUT_MODE_DDR 11 +#define LUT_MODE2_DDR 12 +#define LUT_MODE4_DDR 13 +#define LUT_READ_DDR 14 +#define LUT_WRITE_DDR 15 +#define LUT_DATA_LEARN 16 + +/* + * The PAD definitions for LUT register. + * + * The pad stands for the lines number of IO[0:3]. + * For example, the Quad read need four IO lines, so you should + * set LUT_PAD4 which means we use four IO lines. + */ +#define LUT_PAD1 0 +#define LUT_PAD2 1 +#define LUT_PAD4 2 + +/* Oprands for the LUT register. */ +#define ADDR24BIT 0x18 +#define ADDR32BIT 0x20 + +/* Macros for constructing the LUT register. */ +#define LUT0(ins, pad, opr) \ + (((opr) << OPRND0_SHIFT) | ((LUT_##pad) << PAD0_SHIFT) | \ + ((LUT_##ins) << INSTR0_SHIFT)) + +#define LUT1(ins, pad, opr) (LUT0(ins, pad, opr) << OPRND1_SHIFT) + +/* other macros for LUT register. */ +#define QUADSPI_LUT(x) (QUADSPI_LUT_BASE + (x) * 4) +#define QUADSPI_LUT_NUM 64 + +/* SEQID -- we can have 16 seqids at most. */ +#define SEQID_QUAD_READ 0 +#define SEQID_WREN 1 +#define SEQID_WRDI 2 +#define SEQID_RDSR 3 +#define SEQID_SE 4 +#define SEQID_CHIP_ERASE 5 +#define SEQID_PP 6 +#define SEQID_RDID 7 +#define SEQID_WRSR 8 +#define SEQID_RDCR 9 +#define SEQID_EN4B 10 +#define SEQID_BRWR 11 + +enum fsl_qspi_devtype { + FSL_QUADSPI_VYBRID, + FSL_QUADSPI_IMX6SX, +}; + +struct fsl_qspi_devtype_data { + enum fsl_qspi_devtype devtype; + int rxfifo; + int txfifo; +}; + +static struct fsl_qspi_devtype_data vybrid_data = { + .devtype = FSL_QUADSPI_VYBRID, + .rxfifo = 128, + .txfifo = 64 +}; + +static struct fsl_qspi_devtype_data imx6sx_data = { + .devtype = FSL_QUADSPI_IMX6SX, + .rxfifo = 128, + .txfifo = 512 +}; + +#define FSL_QSPI_MAX_CHIP 4 +struct fsl_qspi { + struct mtd_info mtd[FSL_QSPI_MAX_CHIP]; + struct spi_nor nor[FSL_QSPI_MAX_CHIP]; + void __iomem *iobase; + void __iomem *ahb_base; /* Used when read from AHB bus */ + u32 memmap_phy; + struct clk *clk, *clk_en; + struct device *dev; + struct completion c; + struct fsl_qspi_devtype_data *devtype_data; + u32 nor_size; + u32 nor_num; + u32 clk_rate; + unsigned int chip_base_addr; /* We may support two chips. */ +}; + +static inline int is_vybrid_qspi(struct fsl_qspi *q) +{ + return q->devtype_data->devtype == FSL_QUADSPI_VYBRID; +} + +static inline int is_imx6sx_qspi(struct fsl_qspi *q) +{ + return q->devtype_data->devtype == FSL_QUADSPI_IMX6SX; +} + +/* + * An IC bug makes us to re-arrange the 32-bit data. + * The following chips, such as IMX6SLX, have fixed this bug. + */ +static inline u32 fsl_qspi_endian_xchg(struct fsl_qspi *q, u32 a) +{ + return is_vybrid_qspi(q) ? __swab32(a) : a; +} + +static inline void fsl_qspi_unlock_lut(struct fsl_qspi *q) +{ + writel(QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY); + writel(QUADSPI_LCKER_UNLOCK, q->iobase + QUADSPI_LCKCR); +} + +static inline void fsl_qspi_lock_lut(struct fsl_qspi *q) +{ + writel(QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY); + writel(QUADSPI_LCKER_LOCK, q->iobase + QUADSPI_LCKCR); +} + +static irqreturn_t fsl_qspi_irq_handler(int irq, void *dev_id) +{ + struct fsl_qspi *q = dev_id; + u32 reg; + + /* clear interrupt */ + reg = readl(q->iobase + QUADSPI_FR); + writel(reg, q->iobase + QUADSPI_FR); + + if (reg & QUADSPI_FR_TFF_MASK) + complete(&q->c); + + dev_dbg(q->dev, "QUADSPI_FR : 0x%.8x:0x%.8x\n", q->chip_base_addr, reg); + return IRQ_HANDLED; +} + +static void fsl_qspi_init_lut(struct fsl_qspi *q) +{ + void __iomem *base = q->iobase; + int rxfifo = q->devtype_data->rxfifo; + u32 lut_base; + u8 cmd, addrlen, dummy; + int i; + + fsl_qspi_unlock_lut(q); + + /* Clear all the LUT table */ + for (i = 0; i < QUADSPI_LUT_NUM; i++) + writel(0, base + QUADSPI_LUT_BASE + i * 4); + + /* Quad Read */ + lut_base = SEQID_QUAD_READ * 4; + + if (q->nor_size <= SZ_16M) { + cmd = SPINOR_OP_READ_1_1_4; + addrlen = ADDR24BIT; + dummy = 8; + } else { + /* use the 4-byte address */ + cmd = SPINOR_OP_READ_1_1_4; + addrlen = ADDR32BIT; + dummy = 8; + } + + writel(LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen), + base + QUADSPI_LUT(lut_base)); + writel(LUT0(DUMMY, PAD1, dummy) | LUT1(READ, PAD4, rxfifo), + base + QUADSPI_LUT(lut_base + 1)); + + /* Write enable */ + lut_base = SEQID_WREN * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_WREN), base + QUADSPI_LUT(lut_base)); + + /* Page Program */ + lut_base = SEQID_PP * 4; + + if (q->nor_size <= SZ_16M) { + cmd = SPINOR_OP_PP; + addrlen = ADDR24BIT; + } else { + /* use the 4-byte address */ + cmd = SPINOR_OP_PP; + addrlen = ADDR32BIT; + } + + writel(LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen), + base + QUADSPI_LUT(lut_base)); + writel(LUT0(WRITE, PAD1, 0), base + QUADSPI_LUT(lut_base + 1)); + + /* Read Status */ + lut_base = SEQID_RDSR * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_RDSR) | LUT1(READ, PAD1, 0x1), + base + QUADSPI_LUT(lut_base)); + + /* Erase a sector */ + lut_base = SEQID_SE * 4; + + if (q->nor_size <= SZ_16M) { + cmd = SPINOR_OP_SE; + addrlen = ADDR24BIT; + } else { + /* use the 4-byte address */ + cmd = SPINOR_OP_SE; + addrlen = ADDR32BIT; + } + + writel(LUT0(CMD, PAD1, cmd) | LUT1(ADDR, PAD1, addrlen), + base + QUADSPI_LUT(lut_base)); + + /* Erase the whole chip */ + lut_base = SEQID_CHIP_ERASE * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_CHIP_ERASE), + base + QUADSPI_LUT(lut_base)); + + /* READ ID */ + lut_base = SEQID_RDID * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_RDID) | LUT1(READ, PAD1, 0x8), + base + QUADSPI_LUT(lut_base)); + + /* Write Register */ + lut_base = SEQID_WRSR * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_WRSR) | LUT1(WRITE, PAD1, 0x2), + base + QUADSPI_LUT(lut_base)); + + /* Read Configuration Register */ + lut_base = SEQID_RDCR * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_RDCR) | LUT1(READ, PAD1, 0x1), + base + QUADSPI_LUT(lut_base)); + + /* Write disable */ + lut_base = SEQID_WRDI * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_WRDI), base + QUADSPI_LUT(lut_base)); + + /* Enter 4 Byte Mode (Micron) */ + lut_base = SEQID_EN4B * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_EN4B), base + QUADSPI_LUT(lut_base)); + + /* Enter 4 Byte Mode (Spansion) */ + lut_base = SEQID_BRWR * 4; + writel(LUT0(CMD, PAD1, SPINOR_OP_BRWR), base + QUADSPI_LUT(lut_base)); + + fsl_qspi_lock_lut(q); +} + +/* Get the SEQID for the command */ +static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd) +{ + switch (cmd) { + case SPINOR_OP_READ_1_1_4: + return SEQID_QUAD_READ; + case SPINOR_OP_WREN: + return SEQID_WREN; + case SPINOR_OP_WRDI: + return SEQID_WRDI; + case SPINOR_OP_RDSR: + return SEQID_RDSR; + case SPINOR_OP_SE: + return SEQID_SE; + case SPINOR_OP_CHIP_ERASE: + return SEQID_CHIP_ERASE; + case SPINOR_OP_PP: + return SEQID_PP; + case SPINOR_OP_RDID: + return SEQID_RDID; + case SPINOR_OP_WRSR: + return SEQID_WRSR; + case SPINOR_OP_RDCR: + return SEQID_RDCR; + case SPINOR_OP_EN4B: + return SEQID_EN4B; + case SPINOR_OP_BRWR: + return SEQID_BRWR; + default: + dev_err(q->dev, "Unsupported cmd 0x%.2x\n", cmd); + break; + } + return -EINVAL; +} + +static int +fsl_qspi_runcmd(struct fsl_qspi *q, u8 cmd, unsigned int addr, int len) +{ + void __iomem *base = q->iobase; + int seqid; + u32 reg, reg2; + int err; + + init_completion(&q->c); + dev_dbg(q->dev, "to 0x%.8x:0x%.8x, len:%d, cmd:%.2x\n", + q->chip_base_addr, addr, len, cmd); + + /* save the reg */ + reg = readl(base + QUADSPI_MCR); + + writel(q->memmap_phy + q->chip_base_addr + addr, base + QUADSPI_SFAR); + writel(QUADSPI_RBCT_WMRK_MASK | QUADSPI_RBCT_RXBRD_USEIPS, + base + QUADSPI_RBCT); + writel(reg | QUADSPI_MCR_CLR_RXF_MASK, base + QUADSPI_MCR); + + do { + reg2 = readl(base + QUADSPI_SR); + if (reg2 & (QUADSPI_SR_IP_ACC_MASK | QUADSPI_SR_AHB_ACC_MASK)) { + udelay(1); + dev_dbg(q->dev, "The controller is busy, 0x%x\n", reg2); + continue; + } + break; + } while (1); + + /* trigger the LUT now */ + seqid = fsl_qspi_get_seqid(q, cmd); + writel((seqid << QUADSPI_IPCR_SEQID_SHIFT) | len, base + QUADSPI_IPCR); + + /* Wait for the interrupt. */ + err = wait_for_completion_timeout(&q->c, msecs_to_jiffies(1000)); + if (!err) { + dev_err(q->dev, + "cmd 0x%.2x timeout, addr@%.8x, FR:0x%.8x, SR:0x%.8x\n", + cmd, addr, readl(base + QUADSPI_FR), + readl(base + QUADSPI_SR)); + err = -ETIMEDOUT; + } else { + err = 0; + } + + /* restore the MCR */ + writel(reg, base + QUADSPI_MCR); + + return err; +} + +/* Read out the data from the QUADSPI_RBDR buffer registers. */ +static void fsl_qspi_read_data(struct fsl_qspi *q, int len, u8 *rxbuf) +{ + u32 tmp; + int i = 0; + + while (len > 0) { + tmp = readl(q->iobase + QUADSPI_RBDR + i * 4); + tmp = fsl_qspi_endian_xchg(q, tmp); + dev_dbg(q->dev, "chip addr:0x%.8x, rcv:0x%.8x\n", + q->chip_base_addr, tmp); + + if (len >= 4) { + *((u32 *)rxbuf) = tmp; + rxbuf += 4; + } else { + memcpy(rxbuf, &tmp, len); + break; + } + + len -= 4; + i++; + } +} + +/* + * If we have changed the content of the flash by writing or erasing, + * we need to invalidate the AHB buffer. If we do not do so, we may read out + * the wrong data. The spec tells us reset the AHB domain and Serial Flash + * domain at the same time. + */ +static inline void fsl_qspi_invalid(struct fsl_qspi *q) +{ + u32 reg; + + reg = readl(q->iobase + QUADSPI_MCR); + reg |= QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK; + writel(reg, q->iobase + QUADSPI_MCR); + + /* + * The minimum delay : 1 AHB + 2 SFCK clocks. + * Delay 1 us is enough. + */ + udelay(1); + + reg &= ~(QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK); + writel(reg, q->iobase + QUADSPI_MCR); +} + +static int fsl_qspi_nor_write(struct fsl_qspi *q, struct spi_nor *nor, + u8 opcode, unsigned int to, u32 *txbuf, + unsigned count, size_t *retlen) +{ + int ret, i, j; + u32 tmp; + + dev_dbg(q->dev, "to 0x%.8x:0x%.8x, len : %d\n", + q->chip_base_addr, to, count); + + /* clear the TX FIFO. */ + tmp = readl(q->iobase + QUADSPI_MCR); + writel(tmp | QUADSPI_MCR_CLR_RXF_MASK, q->iobase + QUADSPI_MCR); + + /* fill the TX data to the FIFO */ + for (j = 0, i = ((count + 3) / 4); j < i; j++) { + tmp = fsl_qspi_endian_xchg(q, *txbuf); + writel(tmp, q->iobase + QUADSPI_TBDR); + txbuf++; + } + + /* Trigger it */ + ret = fsl_qspi_runcmd(q, opcode, to, count); + + if (ret == 0 && retlen) + *retlen += count; + + return ret; +} + +static void fsl_qspi_set_map_addr(struct fsl_qspi *q) +{ + int nor_size = q->nor_size; + void __iomem *base = q->iobase; + + writel(nor_size + q->memmap_phy, base + QUADSPI_SFA1AD); + writel(nor_size * 2 + q->memmap_phy, base + QUADSPI_SFA2AD); + writel(nor_size * 3 + q->memmap_phy, base + QUADSPI_SFB1AD); + writel(nor_size * 4 + q->memmap_phy, base + QUADSPI_SFB2AD); +} + +/* + * There are two different ways to read out the data from the flash: + * the "IP Command Read" and the "AHB Command Read". + * + * The IC guy suggests we use the "AHB Command Read" which is faster + * then the "IP Command Read". (What's more is that there is a bug in + * the "IP Command Read" in the Vybrid.) + * + * After we set up the registers for the "AHB Command Read", we can use + * the memcpy to read the data directly. A "missed" access to the buffer + * causes the controller to clear the buffer, and use the sequence pointed + * by the QUADSPI_BFGENCR[SEQID] to initiate a read from the flash. + */ +static void fsl_qspi_init_abh_read(struct fsl_qspi *q) +{ + void __iomem *base = q->iobase; + int seqid; + + /* AHB configuration for access buffer 0/1/2 .*/ + writel(QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF0CR); + writel(QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF1CR); + writel(QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF2CR); + writel(QUADSPI_BUF3CR_ALLMST, base + QUADSPI_BUF3CR); + + /* We only use the buffer3 */ + writel(0, base + QUADSPI_BUF0IND); + writel(0, base + QUADSPI_BUF1IND); + writel(0, base + QUADSPI_BUF2IND); + + /* Set the default lut sequence for AHB Read. */ + seqid = fsl_qspi_get_seqid(q, q->nor[0].read_opcode); + writel(seqid << QUADSPI_BFGENCR_SEQID_SHIFT, + q->iobase + QUADSPI_BFGENCR); +} + +/* We use this function to do some basic init for spi_nor_scan(). */ +static int fsl_qspi_nor_setup(struct fsl_qspi *q) +{ + void __iomem *base = q->iobase; + u32 reg; + int ret; + + /* the default frequency, we will change it in the future.*/ + ret = clk_set_rate(q->clk, 66000000); + if (ret) + return ret; + + /* Init the LUT table. */ + fsl_qspi_init_lut(q); + + /* Disable the module */ + writel(QUADSPI_MCR_MDIS_MASK | QUADSPI_MCR_RESERVED_MASK, + base + QUADSPI_MCR); + + reg = readl(base + QUADSPI_SMPR); + writel(reg & ~(QUADSPI_SMPR_FSDLY_MASK + | QUADSPI_SMPR_FSPHS_MASK + | QUADSPI_SMPR_HSENA_MASK + | QUADSPI_SMPR_DDRSMP_MASK), base + QUADSPI_SMPR); + + /* Enable the module */ + writel(QUADSPI_MCR_RESERVED_MASK | QUADSPI_MCR_END_CFG_MASK, + base + QUADSPI_MCR); + + /* enable the interrupt */ + writel(QUADSPI_RSER_TFIE, q->iobase + QUADSPI_RSER); + + return 0; +} + +static int fsl_qspi_nor_setup_last(struct fsl_qspi *q) +{ + unsigned long rate = q->clk_rate; + int ret; + + if (is_imx6sx_qspi(q)) + rate *= 4; + + ret = clk_set_rate(q->clk, rate); + if (ret) + return ret; + + /* Init the LUT table again. */ + fsl_qspi_init_lut(q); + + /* Init for AHB read */ + fsl_qspi_init_abh_read(q); + + return 0; +} + +static struct of_device_id fsl_qspi_dt_ids[] = { + { .compatible = "fsl,vf610-qspi", .data = (void *)&vybrid_data, }, + { .compatible = "fsl,imx6sx-qspi", .data = (void *)&imx6sx_data, }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, fsl_qspi_dt_ids); + +static void fsl_qspi_set_base_addr(struct fsl_qspi *q, struct spi_nor *nor) +{ + q->chip_base_addr = q->nor_size * (nor - q->nor); +} + +static int fsl_qspi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len) +{ + int ret; + struct fsl_qspi *q = nor->priv; + + ret = fsl_qspi_runcmd(q, opcode, 0, len); + if (ret) + return ret; + + fsl_qspi_read_data(q, len, buf); + return 0; +} + +static int fsl_qspi_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len, + int write_enable) +{ + struct fsl_qspi *q = nor->priv; + int ret; + + if (!buf) { + ret = fsl_qspi_runcmd(q, opcode, 0, 1); + if (ret) + return ret; + + if (opcode == SPINOR_OP_CHIP_ERASE) + fsl_qspi_invalid(q); + + } else if (len > 0) { + ret = fsl_qspi_nor_write(q, nor, opcode, 0, + (u32 *)buf, len, NULL); + } else { + dev_err(q->dev, "invalid cmd %d\n", opcode); + ret = -EINVAL; + } + + return ret; +} + +static void fsl_qspi_write(struct spi_nor *nor, loff_t to, + size_t len, size_t *retlen, const u_char *buf) +{ + struct fsl_qspi *q = nor->priv; + + fsl_qspi_nor_write(q, nor, nor->program_opcode, to, + (u32 *)buf, len, retlen); + + /* invalid the data in the AHB buffer. */ + fsl_qspi_invalid(q); +} + +static int fsl_qspi_read(struct spi_nor *nor, loff_t from, + size_t len, size_t *retlen, u_char *buf) +{ + struct fsl_qspi *q = nor->priv; + u8 cmd = nor->read_opcode; + int ret; + + dev_dbg(q->dev, "cmd [%x],read from (0x%p, 0x%.8x, 0x%.8x),len:%d\n", + cmd, q->ahb_base, q->chip_base_addr, (unsigned int)from, len); + + /* Wait until the previous command is finished. */ + ret = nor->wait_till_ready(nor); + if (ret) + return ret; + + /* Read out the data directly from the AHB buffer.*/ + memcpy(buf, q->ahb_base + q->chip_base_addr + from, len); + + *retlen += len; + return 0; +} + +static int fsl_qspi_erase(struct spi_nor *nor, loff_t offs) +{ + struct fsl_qspi *q = nor->priv; + int ret; + + dev_dbg(nor->dev, "%dKiB at 0x%08x:0x%08x\n", + nor->mtd->erasesize / 1024, q->chip_base_addr, (u32)offs); + + /* Wait until finished previous write command. */ + ret = nor->wait_till_ready(nor); + if (ret) + return ret; + + /* Send write enable, then erase commands. */ + ret = nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0, 0); + if (ret) + return ret; + + ret = fsl_qspi_runcmd(q, nor->erase_opcode, offs, 0); + if (ret) + return ret; + + fsl_qspi_invalid(q); + return 0; +} + +static int fsl_qspi_prep(struct spi_nor *nor, enum spi_nor_ops ops) +{ + struct fsl_qspi *q = nor->priv; + int ret; + + ret = clk_enable(q->clk_en); + if (ret) + return ret; + + ret = clk_enable(q->clk); + if (ret) { + clk_disable(q->clk_en); + return ret; + } + + fsl_qspi_set_base_addr(q, nor); + return 0; +} + +static void fsl_qspi_unprep(struct spi_nor *nor, enum spi_nor_ops ops) +{ + struct fsl_qspi *q = nor->priv; + + clk_disable(q->clk); + clk_disable(q->clk_en); +} + +static int fsl_qspi_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct mtd_part_parser_data ppdata; + struct device *dev = &pdev->dev; + struct fsl_qspi *q; + struct resource *res; + struct spi_nor *nor; + struct mtd_info *mtd; + int ret, i = 0; + bool has_second_chip = false; + const struct of_device_id *of_id = + of_match_device(fsl_qspi_dt_ids, &pdev->dev); + + q = devm_kzalloc(dev, sizeof(*q), GFP_KERNEL); + if (!q) + return -ENOMEM; + + q->nor_num = of_get_child_count(dev->of_node); + if (!q->nor_num || q->nor_num > FSL_QSPI_MAX_CHIP) + return -ENODEV; + + /* find the resources */ + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "QuadSPI"); + q->iobase = devm_ioremap_resource(dev, res); + if (IS_ERR(q->iobase)) { + ret = PTR_ERR(q->iobase); + goto map_failed; + } + + res = platform_get_resource_byname(pdev, IORESOURCE_MEM, + "QuadSPI-memory"); + q->ahb_base = devm_ioremap_resource(dev, res); + if (IS_ERR(q->ahb_base)) { + ret = PTR_ERR(q->ahb_base); + goto map_failed; + } + q->memmap_phy = res->start; + + /* find the clocks */ + q->clk_en = devm_clk_get(dev, "qspi_en"); + if (IS_ERR(q->clk_en)) { + ret = PTR_ERR(q->clk_en); + goto map_failed; + } + + q->clk = devm_clk_get(dev, "qspi"); + if (IS_ERR(q->clk)) { + ret = PTR_ERR(q->clk); + goto map_failed; + } + + ret = clk_prepare_enable(q->clk_en); + if (ret) { + dev_err(dev, "can not enable the qspi_en clock\n"); + goto map_failed; + } + + ret = clk_prepare_enable(q->clk); + if (ret) { + clk_disable_unprepare(q->clk_en); + dev_err(dev, "can not enable the qspi clock\n"); + goto map_failed; + } + + /* find the irq */ + ret = platform_get_irq(pdev, 0); + if (ret < 0) { + dev_err(dev, "failed to get the irq\n"); + goto irq_failed; + } + + ret = devm_request_irq(dev, ret, + fsl_qspi_irq_handler, 0, pdev->name, q); + if (ret) { + dev_err(dev, "failed to request irq.\n"); + goto irq_failed; + } + + q->dev = dev; + q->devtype_data = (struct fsl_qspi_devtype_data *)of_id->data; + platform_set_drvdata(pdev, q); + + ret = fsl_qspi_nor_setup(q); + if (ret) + goto irq_failed; + + if (of_get_property(np, "fsl,qspi-has-second-chip", NULL)) + has_second_chip = true; + + /* iterate the subnodes. */ + for_each_available_child_of_node(dev->of_node, np) { + const struct spi_device_id *id; + char modalias[40]; + + /* skip the holes */ + if (!has_second_chip) + i *= 2; + + nor = &q->nor[i]; + mtd = &q->mtd[i]; + + nor->mtd = mtd; + nor->dev = dev; + nor->priv = q; + mtd->priv = nor; + + /* fill the hooks */ + nor->read_reg = fsl_qspi_read_reg; + nor->write_reg = fsl_qspi_write_reg; + nor->read = fsl_qspi_read; + nor->write = fsl_qspi_write; + nor->erase = fsl_qspi_erase; + + nor->prepare = fsl_qspi_prep; + nor->unprepare = fsl_qspi_unprep; + + if (of_modalias_node(np, modalias, sizeof(modalias)) < 0) + goto map_failed; + + id = spi_nor_match_id(modalias); + if (!id) + goto map_failed; + + ret = of_property_read_u32(np, "spi-max-frequency", + &q->clk_rate); + if (ret < 0) + goto map_failed; + + /* set the chip address for READID */ + fsl_qspi_set_base_addr(q, nor); + + ret = spi_nor_scan(nor, id, SPI_NOR_QUAD); + if (ret) + goto map_failed; + + ppdata.of_node = np; + ret = mtd_device_parse_register(mtd, NULL, &ppdata, NULL, 0); + if (ret) + goto map_failed; + + /* Set the correct NOR size now. */ + if (q->nor_size == 0) { + q->nor_size = mtd->size; + + /* Map the SPI NOR to accessiable address */ + fsl_qspi_set_map_addr(q); + } + + /* + * The TX FIFO is 64 bytes in the Vybrid, but the Page Program + * may writes 265 bytes per time. The write is working in the + * unit of the TX FIFO, not in the unit of the SPI NOR's page + * size. + * + * So shrink the spi_nor->page_size if it is larger then the + * TX FIFO. + */ + if (nor->page_size > q->devtype_data->txfifo) + nor->page_size = q->devtype_data->txfifo; + + i++; + } + + /* finish the rest init. */ + ret = fsl_qspi_nor_setup_last(q); + if (ret) + goto last_init_failed; + + clk_disable(q->clk); + clk_disable(q->clk_en); + dev_info(dev, "QuadSPI SPI NOR flash driver\n"); + return 0; + +last_init_failed: + for (i = 0; i < q->nor_num; i++) + mtd_device_unregister(&q->mtd[i]); + +irq_failed: + clk_disable_unprepare(q->clk); + clk_disable_unprepare(q->clk_en); +map_failed: + dev_err(dev, "Freescale QuadSPI probe failed\n"); + return ret; +} + +static int fsl_qspi_remove(struct platform_device *pdev) +{ + struct fsl_qspi *q = platform_get_drvdata(pdev); + int i; + + for (i = 0; i < q->nor_num; i++) + mtd_device_unregister(&q->mtd[i]); + + /* disable the hardware */ + writel(QUADSPI_MCR_MDIS_MASK, q->iobase + QUADSPI_MCR); + writel(0x0, q->iobase + QUADSPI_RSER); + + clk_unprepare(q->clk); + clk_unprepare(q->clk_en); + return 0; +} + +static struct platform_driver fsl_qspi_driver = { + .driver = { + .name = "fsl-quadspi", + .bus = &platform_bus_type, + .owner = THIS_MODULE, + .of_match_table = fsl_qspi_dt_ids, + }, + .probe = fsl_qspi_probe, + .remove = fsl_qspi_remove, +}; +module_platform_driver(fsl_qspi_driver); + +MODULE_DESCRIPTION("Freescale QuadSPI Controller Driver"); +MODULE_AUTHOR("Freescale Semiconductor Inc."); +MODULE_LICENSE("GPL v2"); --- /dev/null +++ b/drivers/mtd/spi-nor/Kconfig @@ -0,0 +1,17 @@ +menuconfig MTD_SPI_NOR + tristate "SPI-NOR device support" + depends on MTD + help + This is the framework for the SPI NOR which can be used by the SPI + device drivers and the SPI-NOR device driver. + +if MTD_SPI_NOR + +config SPI_FSL_QUADSPI + tristate "Freescale Quad SPI controller" + depends on ARCH_MXC + help + This enables support for the Quad SPI controller in master mode. + We only connect the NOR to this controller now. + +endif # MTD_SPI_NOR --- /dev/null +++ b/drivers/mtd/spi-nor/Makefile @@ -0,0 +1,2 @@ +obj-$(CONFIG_MTD_SPI_NOR) += spi-nor.o +obj-$(CONFIG_SPI_FSL_QUADSPI) += fsl-quadspi.o --- /dev/null +++ b/drivers/mtd/spi-nor/spi-nor.c @@ -0,0 +1,1160 @@ +/* + * Based on m25p80.c, by Mike Lavender (mike@steroidmicros.com), with + * influence from lart.c (Abraham Van Der Merwe) and mtd_dataflash.c + * + * Copyright (C) 2005, Intec Automation Inc. + * Copyright (C) 2014, Freescale Semiconductor, Inc. + * + * This code is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +/* Define max times to check status register before we give up. */ +#define MAX_READY_WAIT_JIFFIES (40 * HZ) /* M25P16 specs 40s max chip erase */ + +#define JEDEC_MFR(_jedec_id) ((_jedec_id) >> 16) + +/* + * Read the status register, returning its value in the location + * Return the status register value. + * Returns negative if error occurred. + */ +static int read_sr(struct spi_nor *nor) +{ + int ret; + u8 val; + + ret = nor->read_reg(nor, SPINOR_OP_RDSR, &val, 1); + if (ret < 0) { + pr_err("error %d reading SR\n", (int) ret); + return ret; + } + + return val; +} + +/* + * Read the flag status register, returning its value in the location + * Return the status register value. + * Returns negative if error occurred. + */ +static int read_fsr(struct spi_nor *nor) +{ + int ret; + u8 val; + + ret = nor->read_reg(nor, SPINOR_OP_RDFSR, &val, 1); + if (ret < 0) { + pr_err("error %d reading FSR\n", ret); + return ret; + } + + return val; +} + +/* + * Read configuration register, returning its value in the + * location. Return the configuration register value. + * Returns negative if error occured. + */ +static int read_cr(struct spi_nor *nor) +{ + int ret; + u8 val; + + ret = nor->read_reg(nor, SPINOR_OP_RDCR, &val, 1); + if (ret < 0) { + dev_err(nor->dev, "error %d reading CR\n", ret); + return ret; + } + + return val; +} + +/* + * Dummy Cycle calculation for different type of read. + * It can be used to support more commands with + * different dummy cycle requirements. + */ +static inline int spi_nor_read_dummy_cycles(struct spi_nor *nor) +{ + switch (nor->flash_read) { + case SPI_NOR_FAST: + case SPI_NOR_DUAL: + case SPI_NOR_QUAD: + return 1; + case SPI_NOR_NORMAL: + return 0; + } + return 0; +} + +/* + * Write status register 1 byte + * Returns negative if error occurred. + */ +static inline int write_sr(struct spi_nor *nor, u8 val) +{ + nor->cmd_buf[0] = val; + return nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1, 0); +} + +/* + * Set write enable latch with Write Enable command. + * Returns negative if error occurred. + */ +static inline int write_enable(struct spi_nor *nor) +{ + return nor->write_reg(nor, SPINOR_OP_WREN, NULL, 0, 0); +} + +/* + * Send write disble instruction to the chip. + */ +static inline int write_disable(struct spi_nor *nor) +{ + return nor->write_reg(nor, SPINOR_OP_WRDI, NULL, 0, 0); +} + +static inline struct spi_nor *mtd_to_spi_nor(struct mtd_info *mtd) +{ + return mtd->priv; +} + +/* Enable/disable 4-byte addressing mode. */ +static inline int set_4byte(struct spi_nor *nor, u32 jedec_id, int enable) +{ + int status; + bool need_wren = false; + u8 cmd; + + switch (JEDEC_MFR(jedec_id)) { + case CFI_MFR_ST: /* Micron, actually */ + /* Some Micron need WREN command; all will accept it */ + need_wren = true; + case CFI_MFR_MACRONIX: + case 0xEF /* winbond */: + if (need_wren) + write_enable(nor); + + cmd = enable ? SPINOR_OP_EN4B : SPINOR_OP_EX4B; + status = nor->write_reg(nor, cmd, NULL, 0, 0); + if (need_wren) + write_disable(nor); + + return status; + default: + /* Spansion style */ + nor->cmd_buf[0] = enable << 7; + return nor->write_reg(nor, SPINOR_OP_BRWR, nor->cmd_buf, 1, 0); + } +} + +static int spi_nor_wait_till_ready(struct spi_nor *nor) +{ + unsigned long deadline; + int sr; + + deadline = jiffies + MAX_READY_WAIT_JIFFIES; + + do { + cond_resched(); + + sr = read_sr(nor); + if (sr < 0) + break; + else if (!(sr & SR_WIP)) + return 0; + } while (!time_after_eq(jiffies, deadline)); + + return -ETIMEDOUT; +} + +static int spi_nor_wait_till_fsr_ready(struct spi_nor *nor) +{ + unsigned long deadline; + int sr; + int fsr; + + deadline = jiffies + MAX_READY_WAIT_JIFFIES; + + do { + cond_resched(); + + sr = read_sr(nor); + if (sr < 0) { + break; + } else if (!(sr & SR_WIP)) { + fsr = read_fsr(nor); + if (fsr < 0) + break; + if (fsr & FSR_READY) + return 0; + } + } while (!time_after_eq(jiffies, deadline)); + + return -ETIMEDOUT; +} + +/* + * Service routine to read status register until ready, or timeout occurs. + * Returns non-zero if error. + */ +static int wait_till_ready(struct spi_nor *nor) +{ + return nor->wait_till_ready(nor); +} + +/* + * Erase the whole flash memory + * + * Returns 0 if successful, non-zero otherwise. + */ +static int erase_chip(struct spi_nor *nor) +{ + int ret; + + dev_dbg(nor->dev, " %lldKiB\n", (long long)(nor->mtd->size >> 10)); + + /* Wait until finished previous write command. */ + ret = wait_till_ready(nor); + if (ret) + return ret; + + /* Send write enable, then erase commands. */ + write_enable(nor); + + return nor->write_reg(nor, SPINOR_OP_CHIP_ERASE, NULL, 0, 0); +} + +static int spi_nor_lock_and_prep(struct spi_nor *nor, enum spi_nor_ops ops) +{ + int ret = 0; + + mutex_lock(&nor->lock); + + if (nor->prepare) { + ret = nor->prepare(nor, ops); + if (ret) { + dev_err(nor->dev, "failed in the preparation.\n"); + mutex_unlock(&nor->lock); + return ret; + } + } + return ret; +} + +static void spi_nor_unlock_and_unprep(struct spi_nor *nor, enum spi_nor_ops ops) +{ + if (nor->unprepare) + nor->unprepare(nor, ops); + mutex_unlock(&nor->lock); +} + +/* + * Erase an address range on the nor chip. The address range may extend + * one or more erase sectors. Return an error is there is a problem erasing. + */ +static int spi_nor_erase(struct mtd_info *mtd, struct erase_info *instr) +{ + struct spi_nor *nor = mtd_to_spi_nor(mtd); + u32 addr, len; + uint32_t rem; + int ret; + + dev_dbg(nor->dev, "at 0x%llx, len %lld\n", (long long)instr->addr, + (long long)instr->len); + + div_u64_rem(instr->len, mtd->erasesize, &rem); + if (rem) + return -EINVAL; + + addr = instr->addr; + len = instr->len; + + ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_ERASE); + if (ret) + return ret; + + /* whole-chip erase? */ + if (len == mtd->size) { + if (erase_chip(nor)) { + ret = -EIO; + goto erase_err; + } + + /* REVISIT in some cases we could speed up erasing large regions + * by using SPINOR_OP_SE instead of SPINOR_OP_BE_4K. We may have set up + * to use "small sector erase", but that's not always optimal. + */ + + /* "sector"-at-a-time erase */ + } else { + while (len) { + if (nor->erase(nor, addr)) { + ret = -EIO; + goto erase_err; + } + + addr += mtd->erasesize; + len -= mtd->erasesize; + } + } + + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_ERASE); + + instr->state = MTD_ERASE_DONE; + mtd_erase_callback(instr); + + return ret; + +erase_err: + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_ERASE); + instr->state = MTD_ERASE_FAILED; + return ret; +} + +static int spi_nor_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len) +{ + struct spi_nor *nor = mtd_to_spi_nor(mtd); + uint32_t offset = ofs; + uint8_t status_old, status_new; + int ret = 0; + + ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_LOCK); + if (ret) + return ret; + + /* Wait until finished previous command */ + ret = wait_till_ready(nor); + if (ret) + goto err; + + status_old = read_sr(nor); + + if (offset < mtd->size - (mtd->size / 2)) + status_new = status_old | SR_BP2 | SR_BP1 | SR_BP0; + else if (offset < mtd->size - (mtd->size / 4)) + status_new = (status_old & ~SR_BP0) | SR_BP2 | SR_BP1; + else if (offset < mtd->size - (mtd->size / 8)) + status_new = (status_old & ~SR_BP1) | SR_BP2 | SR_BP0; + else if (offset < mtd->size - (mtd->size / 16)) + status_new = (status_old & ~(SR_BP0 | SR_BP1)) | SR_BP2; + else if (offset < mtd->size - (mtd->size / 32)) + status_new = (status_old & ~SR_BP2) | SR_BP1 | SR_BP0; + else if (offset < mtd->size - (mtd->size / 64)) + status_new = (status_old & ~(SR_BP2 | SR_BP0)) | SR_BP1; + else + status_new = (status_old & ~(SR_BP2 | SR_BP1)) | SR_BP0; + + /* Only modify protection if it will not unlock other areas */ + if ((status_new & (SR_BP2 | SR_BP1 | SR_BP0)) > + (status_old & (SR_BP2 | SR_BP1 | SR_BP0))) { + write_enable(nor); + ret = write_sr(nor, status_new); + if (ret) + goto err; + } + +err: + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_LOCK); + return ret; +} + +static int spi_nor_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len) +{ + struct spi_nor *nor = mtd_to_spi_nor(mtd); + uint32_t offset = ofs; + uint8_t status_old, status_new; + int ret = 0; + + ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_UNLOCK); + if (ret) + return ret; + + /* Wait until finished previous command */ + ret = wait_till_ready(nor); + if (ret) + goto err; + + status_old = read_sr(nor); + + if (offset+len > mtd->size - (mtd->size / 64)) + status_new = status_old & ~(SR_BP2 | SR_BP1 | SR_BP0); + else if (offset+len > mtd->size - (mtd->size / 32)) + status_new = (status_old & ~(SR_BP2 | SR_BP1)) | SR_BP0; + else if (offset+len > mtd->size - (mtd->size / 16)) + status_new = (status_old & ~(SR_BP2 | SR_BP0)) | SR_BP1; + else if (offset+len > mtd->size - (mtd->size / 8)) + status_new = (status_old & ~SR_BP2) | SR_BP1 | SR_BP0; + else if (offset+len > mtd->size - (mtd->size / 4)) + status_new = (status_old & ~(SR_BP0 | SR_BP1)) | SR_BP2; + else if (offset+len > mtd->size - (mtd->size / 2)) + status_new = (status_old & ~SR_BP1) | SR_BP2 | SR_BP0; + else + status_new = (status_old & ~SR_BP0) | SR_BP2 | SR_BP1; + + /* Only modify protection if it will not lock other areas */ + if ((status_new & (SR_BP2 | SR_BP1 | SR_BP0)) < + (status_old & (SR_BP2 | SR_BP1 | SR_BP0))) { + write_enable(nor); + ret = write_sr(nor, status_new); + if (ret) + goto err; + } + +err: + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_UNLOCK); + return ret; +} + +struct flash_info { + /* JEDEC id zero means "no ID" (most older chips); otherwise it has + * a high byte of zero plus three data bytes: the manufacturer id, + * then a two byte device id. + */ + u32 jedec_id; + u16 ext_id; + + /* The size listed here is what works with SPINOR_OP_SE, which isn't + * necessarily called a "sector" by the vendor. + */ + unsigned sector_size; + u16 n_sectors; + + u16 page_size; + u16 addr_width; + + u16 flags; +#define SECT_4K 0x01 /* SPINOR_OP_BE_4K works uniformly */ +#define SPI_NOR_NO_ERASE 0x02 /* No erase command needed */ +#define SST_WRITE 0x04 /* use SST byte programming */ +#define SPI_NOR_NO_FR 0x08 /* Can't do fastread */ +#define SECT_4K_PMC 0x10 /* SPINOR_OP_BE_4K_PMC works uniformly */ +#define SPI_NOR_DUAL_READ 0x20 /* Flash supports Dual Read */ +#define SPI_NOR_QUAD_READ 0x40 /* Flash supports Quad Read */ +#define USE_FSR 0x80 /* use flag status register */ +}; + +#define INFO(_jedec_id, _ext_id, _sector_size, _n_sectors, _flags) \ + ((kernel_ulong_t)&(struct flash_info) { \ + .jedec_id = (_jedec_id), \ + .ext_id = (_ext_id), \ + .sector_size = (_sector_size), \ + .n_sectors = (_n_sectors), \ + .page_size = 256, \ + .flags = (_flags), \ + }) + +#define CAT25_INFO(_sector_size, _n_sectors, _page_size, _addr_width, _flags) \ + ((kernel_ulong_t)&(struct flash_info) { \ + .sector_size = (_sector_size), \ + .n_sectors = (_n_sectors), \ + .page_size = (_page_size), \ + .addr_width = (_addr_width), \ + .flags = (_flags), \ + }) + +/* NOTE: double check command sets and memory organization when you add + * more nor chips. This current list focusses on newer chips, which + * have been converging on command sets which including JEDEC ID. + */ +const struct spi_device_id spi_nor_ids[] = { + /* Atmel -- some are (confusingly) marketed as "DataFlash" */ + { "at25fs010", INFO(0x1f6601, 0, 32 * 1024, 4, SECT_4K) }, + { "at25fs040", INFO(0x1f6604, 0, 64 * 1024, 8, SECT_4K) }, + + { "at25df041a", INFO(0x1f4401, 0, 64 * 1024, 8, SECT_4K) }, + { "at25df321a", INFO(0x1f4701, 0, 64 * 1024, 64, SECT_4K) }, + { "at25df641", INFO(0x1f4800, 0, 64 * 1024, 128, SECT_4K) }, + + { "at26f004", INFO(0x1f0400, 0, 64 * 1024, 8, SECT_4K) }, + { "at26df081a", INFO(0x1f4501, 0, 64 * 1024, 16, SECT_4K) }, + { "at26df161a", INFO(0x1f4601, 0, 64 * 1024, 32, SECT_4K) }, + { "at26df321", INFO(0x1f4700, 0, 64 * 1024, 64, SECT_4K) }, + + { "at45db081d", INFO(0x1f2500, 0, 64 * 1024, 16, SECT_4K) }, + + /* EON -- en25xxx */ + { "en25f32", INFO(0x1c3116, 0, 64 * 1024, 64, SECT_4K) }, + { "en25p32", INFO(0x1c2016, 0, 64 * 1024, 64, 0) }, + { "en25q32b", INFO(0x1c3016, 0, 64 * 1024, 64, 0) }, + { "en25p64", INFO(0x1c2017, 0, 64 * 1024, 128, 0) }, + { "en25q64", INFO(0x1c3017, 0, 64 * 1024, 128, SECT_4K) }, + { "en25qh128", INFO(0x1c7018, 0, 64 * 1024, 256, 0) }, + { "en25qh256", INFO(0x1c7019, 0, 64 * 1024, 512, 0) }, + + /* ESMT */ + { "f25l32pa", INFO(0x8c2016, 0, 64 * 1024, 64, SECT_4K) }, + + /* Everspin */ + { "mr25h256", CAT25_INFO( 32 * 1024, 1, 256, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) }, + { "mr25h10", CAT25_INFO(128 * 1024, 1, 256, 3, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) }, + + /* GigaDevice */ + { "gd25q32", INFO(0xc84016, 0, 64 * 1024, 64, SECT_4K) }, + { "gd25q64", INFO(0xc84017, 0, 64 * 1024, 128, SECT_4K) }, + + /* Intel/Numonyx -- xxxs33b */ + { "160s33b", INFO(0x898911, 0, 64 * 1024, 32, 0) }, + { "320s33b", INFO(0x898912, 0, 64 * 1024, 64, 0) }, + { "640s33b", INFO(0x898913, 0, 64 * 1024, 128, 0) }, + + /* Macronix */ + { "mx25l2005a", INFO(0xc22012, 0, 64 * 1024, 4, SECT_4K) }, + { "mx25l4005a", INFO(0xc22013, 0, 64 * 1024, 8, SECT_4K) }, + { "mx25l8005", INFO(0xc22014, 0, 64 * 1024, 16, 0) }, + { "mx25l1606e", INFO(0xc22015, 0, 64 * 1024, 32, SECT_4K) }, + { "mx25l3205d", INFO(0xc22016, 0, 64 * 1024, 64, 0) }, + { "mx25l3255e", INFO(0xc29e16, 0, 64 * 1024, 64, SECT_4K) }, + { "mx25l6405d", INFO(0xc22017, 0, 64 * 1024, 128, 0) }, + { "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) }, + { "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) }, + { "mx25l25635e", INFO(0xc22019, 0, 64 * 1024, 512, 0) }, + { "mx25l25655e", INFO(0xc22619, 0, 64 * 1024, 512, 0) }, + { "mx66l51235l", INFO(0xc2201a, 0, 64 * 1024, 1024, SPI_NOR_QUAD_READ) }, + { "mx66l1g55g", INFO(0xc2261b, 0, 64 * 1024, 2048, SPI_NOR_QUAD_READ) }, + + /* Micron */ + { "n25q064", INFO(0x20ba17, 0, 64 * 1024, 128, 0) }, + { "n25q128a11", INFO(0x20bb18, 0, 64 * 1024, 256, 0) }, + { "n25q128a13", INFO(0x20ba18, 0, 64 * 1024, 256, 0) }, + { "n25q256a", INFO(0x20ba19, 0, 64 * 1024, 512, SECT_4K) }, + { "n25q512a", INFO(0x20bb20, 0, 64 * 1024, 1024, SECT_4K) }, + { "n25q512ax3", INFO(0x20ba20, 0, 64 * 1024, 1024, USE_FSR) }, + { "n25q00", INFO(0x20ba21, 0, 64 * 1024, 2048, USE_FSR) }, + + /* PMC */ + { "pm25lv512", INFO(0, 0, 32 * 1024, 2, SECT_4K_PMC) }, + { "pm25lv010", INFO(0, 0, 32 * 1024, 4, SECT_4K_PMC) }, + { "pm25lq032", INFO(0x7f9d46, 0, 64 * 1024, 64, SECT_4K) }, + + /* Spansion -- single (large) sector size only, at least + * for the chips listed here (without boot sectors). + */ + { "s25sl032p", INFO(0x010215, 0x4d00, 64 * 1024, 64, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, + { "s25sl064p", INFO(0x010216, 0x4d00, 64 * 1024, 128, 0) }, + { "s25fl256s0", INFO(0x010219, 0x4d00, 256 * 1024, 128, 0) }, + { "s25fl256s1", INFO(0x010219, 0x4d01, 64 * 1024, 512, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, + { "s25fl512s", INFO(0x010220, 0x4d00, 256 * 1024, 256, SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) }, + { "s70fl01gs", INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) }, + { "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024, 64, 0) }, + { "s25sl12801", INFO(0x012018, 0x0301, 64 * 1024, 256, 0) }, + { "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024, 64, 0) }, + { "s25fl129p1", INFO(0x012018, 0x4d01, 64 * 1024, 256, 0) }, + { "s25sl004a", INFO(0x010212, 0, 64 * 1024, 8, 0) }, + { "s25sl008a", INFO(0x010213, 0, 64 * 1024, 16, 0) }, + { "s25sl016a", INFO(0x010214, 0, 64 * 1024, 32, 0) }, + { "s25sl032a", INFO(0x010215, 0, 64 * 1024, 64, 0) }, + { "s25sl064a", INFO(0x010216, 0, 64 * 1024, 128, 0) }, + { "s25fl008k", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) }, + { "s25fl016k", INFO(0xef4015, 0, 64 * 1024, 32, SECT_4K) }, + { "s25fl064k", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) }, + + /* SST -- large erase sizes are "overlays", "sectors" are 4K */ + { "sst25vf040b", INFO(0xbf258d, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) }, + { "sst25vf080b", INFO(0xbf258e, 0, 64 * 1024, 16, SECT_4K | SST_WRITE) }, + { "sst25vf016b", INFO(0xbf2541, 0, 64 * 1024, 32, SECT_4K | SST_WRITE) }, + { "sst25vf032b", INFO(0xbf254a, 0, 64 * 1024, 64, SECT_4K | SST_WRITE) }, + { "sst25vf064c", INFO(0xbf254b, 0, 64 * 1024, 128, SECT_4K) }, + { "sst25wf512", INFO(0xbf2501, 0, 64 * 1024, 1, SECT_4K | SST_WRITE) }, + { "sst25wf010", INFO(0xbf2502, 0, 64 * 1024, 2, SECT_4K | SST_WRITE) }, + { "sst25wf020", INFO(0xbf2503, 0, 64 * 1024, 4, SECT_4K | SST_WRITE) }, + { "sst25wf040", INFO(0xbf2504, 0, 64 * 1024, 8, SECT_4K | SST_WRITE) }, + + /* ST Microelectronics -- newer production may have feature updates */ + { "m25p05", INFO(0x202010, 0, 32 * 1024, 2, 0) }, + { "m25p10", INFO(0x202011, 0, 32 * 1024, 4, 0) }, + { "m25p20", INFO(0x202012, 0, 64 * 1024, 4, 0) }, + { "m25p40", INFO(0x202013, 0, 64 * 1024, 8, 0) }, + { "m25p80", INFO(0x202014, 0, 64 * 1024, 16, 0) }, + { "m25p16", INFO(0x202015, 0, 64 * 1024, 32, 0) }, + { "m25p32", INFO(0x202016, 0, 64 * 1024, 64, 0) }, + { "m25p64", INFO(0x202017, 0, 64 * 1024, 128, 0) }, + { "m25p128", INFO(0x202018, 0, 256 * 1024, 64, 0) }, + { "n25q032", INFO(0x20ba16, 0, 64 * 1024, 64, 0) }, + + { "m25p05-nonjedec", INFO(0, 0, 32 * 1024, 2, 0) }, + { "m25p10-nonjedec", INFO(0, 0, 32 * 1024, 4, 0) }, + { "m25p20-nonjedec", INFO(0, 0, 64 * 1024, 4, 0) }, + { "m25p40-nonjedec", INFO(0, 0, 64 * 1024, 8, 0) }, + { "m25p80-nonjedec", INFO(0, 0, 64 * 1024, 16, 0) }, + { "m25p16-nonjedec", INFO(0, 0, 64 * 1024, 32, 0) }, + { "m25p32-nonjedec", INFO(0, 0, 64 * 1024, 64, 0) }, + { "m25p64-nonjedec", INFO(0, 0, 64 * 1024, 128, 0) }, + { "m25p128-nonjedec", INFO(0, 0, 256 * 1024, 64, 0) }, + + { "m45pe10", INFO(0x204011, 0, 64 * 1024, 2, 0) }, + { "m45pe80", INFO(0x204014, 0, 64 * 1024, 16, 0) }, + { "m45pe16", INFO(0x204015, 0, 64 * 1024, 32, 0) }, + + { "m25pe20", INFO(0x208012, 0, 64 * 1024, 4, 0) }, + { "m25pe80", INFO(0x208014, 0, 64 * 1024, 16, 0) }, + { "m25pe16", INFO(0x208015, 0, 64 * 1024, 32, SECT_4K) }, + + { "m25px16", INFO(0x207115, 0, 64 * 1024, 32, SECT_4K) }, + { "m25px32", INFO(0x207116, 0, 64 * 1024, 64, SECT_4K) }, + { "m25px32-s0", INFO(0x207316, 0, 64 * 1024, 64, SECT_4K) }, + { "m25px32-s1", INFO(0x206316, 0, 64 * 1024, 64, SECT_4K) }, + { "m25px64", INFO(0x207117, 0, 64 * 1024, 128, 0) }, + + /* Winbond -- w25x "blocks" are 64K, "sectors" are 4KiB */ + { "w25x10", INFO(0xef3011, 0, 64 * 1024, 2, SECT_4K) }, + { "w25x20", INFO(0xef3012, 0, 64 * 1024, 4, SECT_4K) }, + { "w25x40", INFO(0xef3013, 0, 64 * 1024, 8, SECT_4K) }, + { "w25x80", INFO(0xef3014, 0, 64 * 1024, 16, SECT_4K) }, + { "w25x16", INFO(0xef3015, 0, 64 * 1024, 32, SECT_4K) }, + { "w25x32", INFO(0xef3016, 0, 64 * 1024, 64, SECT_4K) }, + { "w25q32", INFO(0xef4016, 0, 64 * 1024, 64, SECT_4K) }, + { "w25q32dw", INFO(0xef6016, 0, 64 * 1024, 64, SECT_4K) }, + { "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) }, + { "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) }, + { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) }, + { "w25q80", INFO(0xef5014, 0, 64 * 1024, 16, SECT_4K) }, + { "w25q80bl", INFO(0xef4014, 0, 64 * 1024, 16, SECT_4K) }, + { "w25q128", INFO(0xef4018, 0, 64 * 1024, 256, SECT_4K) }, + { "w25q256", INFO(0xef4019, 0, 64 * 1024, 512, SECT_4K) }, + + /* Catalyst / On Semiconductor -- non-JEDEC */ + { "cat25c11", CAT25_INFO( 16, 8, 16, 1, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) }, + { "cat25c03", CAT25_INFO( 32, 8, 16, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) }, + { "cat25c09", CAT25_INFO( 128, 8, 32, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) }, + { "cat25c17", CAT25_INFO( 256, 8, 32, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) }, + { "cat25128", CAT25_INFO(2048, 8, 64, 2, SPI_NOR_NO_ERASE | SPI_NOR_NO_FR) }, + { }, +}; +EXPORT_SYMBOL_GPL(spi_nor_ids); + +static const struct spi_device_id *spi_nor_read_id(struct spi_nor *nor) +{ + int tmp; + u8 id[5]; + u32 jedec; + u16 ext_jedec; + struct flash_info *info; + + tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, 5); + if (tmp < 0) { + dev_dbg(nor->dev, " error %d reading JEDEC ID\n", tmp); + return ERR_PTR(tmp); + } + jedec = id[0]; + jedec = jedec << 8; + jedec |= id[1]; + jedec = jedec << 8; + jedec |= id[2]; + + ext_jedec = id[3] << 8 | id[4]; + + for (tmp = 0; tmp < ARRAY_SIZE(spi_nor_ids) - 1; tmp++) { + info = (void *)spi_nor_ids[tmp].driver_data; + if (info->jedec_id == jedec) { + if (info->ext_id == 0 || info->ext_id == ext_jedec) + return &spi_nor_ids[tmp]; + } + } + dev_err(nor->dev, "unrecognized JEDEC id %06x\n", jedec); + return ERR_PTR(-ENODEV); +} + +static const struct spi_device_id *jedec_probe(struct spi_nor *nor) +{ + return nor->read_id(nor); +} + +static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len, + size_t *retlen, u_char *buf) +{ + struct spi_nor *nor = mtd_to_spi_nor(mtd); + int ret; + + dev_dbg(nor->dev, "from 0x%08x, len %zd\n", (u32)from, len); + + ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_READ); + if (ret) + return ret; + + ret = nor->read(nor, from, len, retlen, buf); + + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_READ); + return ret; +} + +static int sst_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf) +{ + struct spi_nor *nor = mtd_to_spi_nor(mtd); + size_t actual; + int ret; + + dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len); + + ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_WRITE); + if (ret) + return ret; + + /* Wait until finished previous write command. */ + ret = wait_till_ready(nor); + if (ret) + goto time_out; + + write_enable(nor); + + nor->sst_write_second = false; + + actual = to % 2; + /* Start write from odd address. */ + if (actual) { + nor->program_opcode = SPINOR_OP_BP; + + /* write one byte. */ + nor->write(nor, to, 1, retlen, buf); + ret = wait_till_ready(nor); + if (ret) + goto time_out; + } + to += actual; + + /* Write out most of the data here. */ + for (; actual < len - 1; actual += 2) { + nor->program_opcode = SPINOR_OP_AAI_WP; + + /* write two bytes. */ + nor->write(nor, to, 2, retlen, buf + actual); + ret = wait_till_ready(nor); + if (ret) + goto time_out; + to += 2; + nor->sst_write_second = true; + } + nor->sst_write_second = false; + + write_disable(nor); + ret = wait_till_ready(nor); + if (ret) + goto time_out; + + /* Write out trailing byte if it exists. */ + if (actual != len) { + write_enable(nor); + + nor->program_opcode = SPINOR_OP_BP; + nor->write(nor, to, 1, retlen, buf + actual); + + ret = wait_till_ready(nor); + if (ret) + goto time_out; + write_disable(nor); + } +time_out: + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_WRITE); + return ret; +} + +/* + * Write an address range to the nor chip. Data must be written in + * FLASH_PAGESIZE chunks. The address range may be any size provided + * it is within the physical boundaries. + */ +static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len, + size_t *retlen, const u_char *buf) +{ + struct spi_nor *nor = mtd_to_spi_nor(mtd); + u32 page_offset, page_size, i; + int ret; + + dev_dbg(nor->dev, "to 0x%08x, len %zd\n", (u32)to, len); + + ret = spi_nor_lock_and_prep(nor, SPI_NOR_OPS_WRITE); + if (ret) + return ret; + + /* Wait until finished previous write command. */ + ret = wait_till_ready(nor); + if (ret) + goto write_err; + + write_enable(nor); + + page_offset = to & (nor->page_size - 1); + + /* do all the bytes fit onto one page? */ + if (page_offset + len <= nor->page_size) { + nor->write(nor, to, len, retlen, buf); + } else { + /* the size of data remaining on the first page */ + page_size = nor->page_size - page_offset; + nor->write(nor, to, page_size, retlen, buf); + + /* write everything in nor->page_size chunks */ + for (i = page_size; i < len; i += page_size) { + page_size = len - i; + if (page_size > nor->page_size) + page_size = nor->page_size; + + wait_till_ready(nor); + write_enable(nor); + + nor->write(nor, to + i, page_size, retlen, buf + i); + } + } + +write_err: + spi_nor_unlock_and_unprep(nor, SPI_NOR_OPS_WRITE); + return 0; +} + +static int macronix_quad_enable(struct spi_nor *nor) +{ + int ret, val; + + val = read_sr(nor); + write_enable(nor); + + nor->cmd_buf[0] = val | SR_QUAD_EN_MX; + nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 1, 0); + + if (wait_till_ready(nor)) + return 1; + + ret = read_sr(nor); + if (!(ret > 0 && (ret & SR_QUAD_EN_MX))) { + dev_err(nor->dev, "Macronix Quad bit not set\n"); + return -EINVAL; + } + + return 0; +} + +/* + * Write status Register and configuration register with 2 bytes + * The first byte will be written to the status register, while the + * second byte will be written to the configuration register. + * Return negative if error occured. + */ +static int write_sr_cr(struct spi_nor *nor, u16 val) +{ + nor->cmd_buf[0] = val & 0xff; + nor->cmd_buf[1] = (val >> 8); + + return nor->write_reg(nor, SPINOR_OP_WRSR, nor->cmd_buf, 2, 0); +} + +static int spansion_quad_enable(struct spi_nor *nor) +{ + int ret; + int quad_en = CR_QUAD_EN_SPAN << 8; + + write_enable(nor); + + ret = write_sr_cr(nor, quad_en); + if (ret < 0) { + dev_err(nor->dev, + "error while writing configuration register\n"); + return -EINVAL; + } + + /* read back and check it */ + ret = read_cr(nor); + if (!(ret > 0 && (ret & CR_QUAD_EN_SPAN))) { + dev_err(nor->dev, "Spansion Quad bit not set\n"); + return -EINVAL; + } + + return 0; +} + +static int set_quad_mode(struct spi_nor *nor, u32 jedec_id) +{ + int status; + + switch (JEDEC_MFR(jedec_id)) { + case CFI_MFR_MACRONIX: + status = macronix_quad_enable(nor); + if (status) { + dev_err(nor->dev, "Macronix quad-read not enabled\n"); + return -EINVAL; + } + return status; + default: + status = spansion_quad_enable(nor); + if (status) { + dev_err(nor->dev, "Spansion quad-read not enabled\n"); + return -EINVAL; + } + return status; + } +} + +static int spi_nor_check(struct spi_nor *nor) +{ + if (!nor->dev || !nor->read || !nor->write || + !nor->read_reg || !nor->write_reg || !nor->erase) { + pr_err("spi-nor: please fill all the necessary fields!\n"); + return -EINVAL; + } + + if (!nor->read_id) + nor->read_id = spi_nor_read_id; + if (!nor->wait_till_ready) + nor->wait_till_ready = spi_nor_wait_till_ready; + + return 0; +} + +int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id, + enum read_mode mode) +{ + struct flash_info *info; + struct flash_platform_data *data; + struct device *dev = nor->dev; + struct mtd_info *mtd = nor->mtd; + struct device_node *np = dev->of_node; + int ret; + int i; + + ret = spi_nor_check(nor); + if (ret) + return ret; + + /* Platform data helps sort out which chip type we have, as + * well as how this board partitions it. If we don't have + * a chip ID, try the JEDEC id commands; they'll work for most + * newer chips, even if we don't recognize the particular chip. + */ + data = dev_get_platdata(dev); + if (data && data->type) { + const struct spi_device_id *plat_id; + + for (i = 0; i < ARRAY_SIZE(spi_nor_ids) - 1; i++) { + plat_id = &spi_nor_ids[i]; + if (strcmp(data->type, plat_id->name)) + continue; + break; + } + + if (i < ARRAY_SIZE(spi_nor_ids) - 1) + id = plat_id; + else + dev_warn(dev, "unrecognized id %s\n", data->type); + } + + info = (void *)id->driver_data; + + if (info->jedec_id) { + const struct spi_device_id *jid; + + jid = jedec_probe(nor); + if (IS_ERR(jid)) { + return PTR_ERR(jid); + } else if (jid != id) { + /* + * JEDEC knows better, so overwrite platform ID. We + * can't trust partitions any longer, but we'll let + * mtd apply them anyway, since some partitions may be + * marked read-only, and we don't want to lose that + * information, even if it's not 100% accurate. + */ + dev_warn(dev, "found %s, expected %s\n", + jid->name, id->name); + id = jid; + info = (void *)jid->driver_data; + } + } + + mutex_init(&nor->lock); + + /* + * Atmel, SST and Intel/Numonyx serial nor tend to power + * up with the software protection bits set + */ + + if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ATMEL || + JEDEC_MFR(info->jedec_id) == CFI_MFR_INTEL || + JEDEC_MFR(info->jedec_id) == CFI_MFR_SST) { + write_enable(nor); + write_sr(nor, 0); + } + + if (data && data->name) + mtd->name = data->name; + else + mtd->name = dev_name(dev); + + mtd->type = MTD_NORFLASH; + mtd->writesize = 1; + mtd->flags = MTD_CAP_NORFLASH; + mtd->size = info->sector_size * info->n_sectors; + mtd->_erase = spi_nor_erase; + mtd->_read = spi_nor_read; + + /* nor protection support for STmicro chips */ + if (JEDEC_MFR(info->jedec_id) == CFI_MFR_ST) { + mtd->_lock = spi_nor_lock; + mtd->_unlock = spi_nor_unlock; + } + + /* sst nor chips use AAI word program */ + if (info->flags & SST_WRITE) + mtd->_write = sst_write; + else + mtd->_write = spi_nor_write; + + if ((info->flags & USE_FSR) && + nor->wait_till_ready == spi_nor_wait_till_ready) + nor->wait_till_ready = spi_nor_wait_till_fsr_ready; + + /* prefer "small sector" erase if possible */ + if (info->flags & SECT_4K) { + nor->erase_opcode = SPINOR_OP_BE_4K; + mtd->erasesize = 4096; + } else if (info->flags & SECT_4K_PMC) { + nor->erase_opcode = SPINOR_OP_BE_4K_PMC; + mtd->erasesize = 4096; + } else { + nor->erase_opcode = SPINOR_OP_SE; + mtd->erasesize = info->sector_size; + } + + if (info->flags & SPI_NOR_NO_ERASE) + mtd->flags |= MTD_NO_ERASE; + + mtd->dev.parent = dev; + nor->page_size = info->page_size; + mtd->writebufsize = nor->page_size; + + if (np) { + /* If we were instantiated by DT, use it */ + if (of_property_read_bool(np, "m25p,fast-read")) + nor->flash_read = SPI_NOR_FAST; + else + nor->flash_read = SPI_NOR_NORMAL; + } else { + /* If we weren't instantiated by DT, default to fast-read */ + nor->flash_read = SPI_NOR_FAST; + } + + /* Some devices cannot do fast-read, no matter what DT tells us */ + if (info->flags & SPI_NOR_NO_FR) + nor->flash_read = SPI_NOR_NORMAL; + + /* Quad/Dual-read mode takes precedence over fast/normal */ + if (mode == SPI_NOR_QUAD && info->flags & SPI_NOR_QUAD_READ) { + ret = set_quad_mode(nor, info->jedec_id); + if (ret) { + dev_err(dev, "quad mode not supported\n"); + return ret; + } + nor->flash_read = SPI_NOR_QUAD; + } else if (mode == SPI_NOR_DUAL && info->flags & SPI_NOR_DUAL_READ) { + nor->flash_read = SPI_NOR_DUAL; + } + + /* Default commands */ + switch (nor->flash_read) { + case SPI_NOR_QUAD: + nor->read_opcode = SPINOR_OP_READ_1_1_4; + break; + case SPI_NOR_DUAL: + nor->read_opcode = SPINOR_OP_READ_1_1_2; + break; + case SPI_NOR_FAST: + nor->read_opcode = SPINOR_OP_READ_FAST; + break; + case SPI_NOR_NORMAL: + nor->read_opcode = SPINOR_OP_READ; + break; + default: + dev_err(dev, "No Read opcode defined\n"); + return -EINVAL; + } + + nor->program_opcode = SPINOR_OP_PP; + + if (info->addr_width) + nor->addr_width = info->addr_width; + else if (mtd->size > 0x1000000) { + /* enable 4-byte addressing if the device exceeds 16MiB */ + nor->addr_width = 4; + if (JEDEC_MFR(info->jedec_id) == CFI_MFR_AMD) { + /* Dedicated 4-byte command set */ + switch (nor->flash_read) { + case SPI_NOR_QUAD: + nor->read_opcode = SPINOR_OP_READ4_1_1_4; + break; + case SPI_NOR_DUAL: + nor->read_opcode = SPINOR_OP_READ4_1_1_2; + break; + case SPI_NOR_FAST: + nor->read_opcode = SPINOR_OP_READ4_FAST; + break; + case SPI_NOR_NORMAL: + nor->read_opcode = SPINOR_OP_READ4; + break; + } + nor->program_opcode = SPINOR_OP_PP_4B; + /* No small sector erase for 4-byte command set */ + nor->erase_opcode = SPINOR_OP_SE_4B; + mtd->erasesize = info->sector_size; + } else + set_4byte(nor, info->jedec_id, 1); + } else { + nor->addr_width = 3; + } + + nor->read_dummy = spi_nor_read_dummy_cycles(nor); + + dev_info(dev, "%s (%lld Kbytes)\n", id->name, + (long long)mtd->size >> 10); + + dev_dbg(dev, + "mtd .name = %s, .size = 0x%llx (%lldMiB), " + ".erasesize = 0x%.8x (%uKiB) .numeraseregions = %d\n", + mtd->name, (long long)mtd->size, (long long)(mtd->size >> 20), + mtd->erasesize, mtd->erasesize / 1024, mtd->numeraseregions); + + if (mtd->numeraseregions) + for (i = 0; i < mtd->numeraseregions; i++) + dev_dbg(dev, + "mtd.eraseregions[%d] = { .offset = 0x%llx, " + ".erasesize = 0x%.8x (%uKiB), " + ".numblocks = %d }\n", + i, (long long)mtd->eraseregions[i].offset, + mtd->eraseregions[i].erasesize, + mtd->eraseregions[i].erasesize / 1024, + mtd->eraseregions[i].numblocks); + return 0; +} +EXPORT_SYMBOL_GPL(spi_nor_scan); + +const struct spi_device_id *spi_nor_match_id(char *name) +{ + const struct spi_device_id *id = spi_nor_ids; + + while (id->name[0]) { + if (!strcmp(name, id->name)) + return id; + id++; + } + return NULL; +} +EXPORT_SYMBOL_GPL(spi_nor_match_id); + +MODULE_LICENSE("GPL"); +MODULE_AUTHOR("Huang Shijie "); +MODULE_AUTHOR("Mike Lavender"); +MODULE_DESCRIPTION("framework for SPI NOR"); --- /dev/null +++ b/include/linux/mtd/spi-nor.h @@ -0,0 +1,218 @@ +/* + * Copyright (C) 2014 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef __LINUX_MTD_SPI_NOR_H +#define __LINUX_MTD_SPI_NOR_H + +/* + * Note on opcode nomenclature: some opcodes have a format like + * SPINOR_OP_FUNCTION{4,}_x_y_z. The numbers x, y, and z stand for the number + * of I/O lines used for the opcode, address, and data (respectively). The + * FUNCTION has an optional suffix of '4', to represent an opcode which + * requires a 4-byte (32-bit) address. + */ + +/* Flash opcodes. */ +#define SPINOR_OP_WREN 0x06 /* Write enable */ +#define SPINOR_OP_RDSR 0x05 /* Read status register */ +#define SPINOR_OP_WRSR 0x01 /* Write status register 1 byte */ +#define SPINOR_OP_READ 0x03 /* Read data bytes (low frequency) */ +#define SPINOR_OP_READ_FAST 0x0b /* Read data bytes (high frequency) */ +#define SPINOR_OP_READ_1_1_2 0x3b /* Read data bytes (Dual SPI) */ +#define SPINOR_OP_READ_1_1_4 0x6b /* Read data bytes (Quad SPI) */ +#define SPINOR_OP_PP 0x02 /* Page program (up to 256 bytes) */ +#define SPINOR_OP_BE_4K 0x20 /* Erase 4KiB block */ +#define SPINOR_OP_BE_4K_PMC 0xd7 /* Erase 4KiB block on PMC chips */ +#define SPINOR_OP_BE_32K 0x52 /* Erase 32KiB block */ +#define SPINOR_OP_CHIP_ERASE 0xc7 /* Erase whole flash chip */ +#define SPINOR_OP_SE 0xd8 /* Sector erase (usually 64KiB) */ +#define SPINOR_OP_RDID 0x9f /* Read JEDEC ID */ +#define SPINOR_OP_RDCR 0x35 /* Read configuration register */ +#define SPINOR_OP_RDFSR 0x70 /* Read flag status register */ + +/* 4-byte address opcodes - used on Spansion and some Macronix flashes. */ +#define SPINOR_OP_READ4 0x13 /* Read data bytes (low frequency) */ +#define SPINOR_OP_READ4_FAST 0x0c /* Read data bytes (high frequency) */ +#define SPINOR_OP_READ4_1_1_2 0x3c /* Read data bytes (Dual SPI) */ +#define SPINOR_OP_READ4_1_1_4 0x6c /* Read data bytes (Quad SPI) */ +#define SPINOR_OP_PP_4B 0x12 /* Page program (up to 256 bytes) */ +#define SPINOR_OP_SE_4B 0xdc /* Sector erase (usually 64KiB) */ + +/* Used for SST flashes only. */ +#define SPINOR_OP_BP 0x02 /* Byte program */ +#define SPINOR_OP_WRDI 0x04 /* Write disable */ +#define SPINOR_OP_AAI_WP 0xad /* Auto address increment word program */ + +/* Used for Macronix and Winbond flashes. */ +#define SPINOR_OP_EN4B 0xb7 /* Enter 4-byte mode */ +#define SPINOR_OP_EX4B 0xe9 /* Exit 4-byte mode */ + +/* Used for Spansion flashes only. */ +#define SPINOR_OP_BRWR 0x17 /* Bank register write */ + +/* Status Register bits. */ +#define SR_WIP 1 /* Write in progress */ +#define SR_WEL 2 /* Write enable latch */ +/* meaning of other SR_* bits may differ between vendors */ +#define SR_BP0 4 /* Block protect 0 */ +#define SR_BP1 8 /* Block protect 1 */ +#define SR_BP2 0x10 /* Block protect 2 */ +#define SR_SRWD 0x80 /* SR write protect */ + +#define SR_QUAD_EN_MX 0x40 /* Macronix Quad I/O */ + +/* Flag Status Register bits */ +#define FSR_READY 0x80 + +/* Configuration Register bits. */ +#define CR_QUAD_EN_SPAN 0x2 /* Spansion Quad I/O */ + +enum read_mode { + SPI_NOR_NORMAL = 0, + SPI_NOR_FAST, + SPI_NOR_DUAL, + SPI_NOR_QUAD, +}; + +/** + * struct spi_nor_xfer_cfg - Structure for defining a Serial Flash transfer + * @wren: command for "Write Enable", or 0x00 for not required + * @cmd: command for operation + * @cmd_pins: number of pins to send @cmd (1, 2, 4) + * @addr: address for operation + * @addr_pins: number of pins to send @addr (1, 2, 4) + * @addr_width: number of address bytes + * (3,4, or 0 for address not required) + * @mode: mode data + * @mode_pins: number of pins to send @mode (1, 2, 4) + * @mode_cycles: number of mode cycles (0 for mode not required) + * @dummy_cycles: number of dummy cycles (0 for dummy not required) + */ +struct spi_nor_xfer_cfg { + u8 wren; + u8 cmd; + u8 cmd_pins; + u32 addr; + u8 addr_pins; + u8 addr_width; + u8 mode; + u8 mode_pins; + u8 mode_cycles; + u8 dummy_cycles; +}; + +#define SPI_NOR_MAX_CMD_SIZE 8 +enum spi_nor_ops { + SPI_NOR_OPS_READ = 0, + SPI_NOR_OPS_WRITE, + SPI_NOR_OPS_ERASE, + SPI_NOR_OPS_LOCK, + SPI_NOR_OPS_UNLOCK, +}; + +/** + * struct spi_nor - Structure for defining a the SPI NOR layer + * @mtd: point to a mtd_info structure + * @lock: the lock for the read/write/erase/lock/unlock operations + * @dev: point to a spi device, or a spi nor controller device. + * @page_size: the page size of the SPI NOR + * @addr_width: number of address bytes + * @erase_opcode: the opcode for erasing a sector + * @read_opcode: the read opcode + * @read_dummy: the dummy needed by the read operation + * @program_opcode: the program opcode + * @flash_read: the mode of the read + * @sst_write_second: used by the SST write operation + * @cfg: used by the read_xfer/write_xfer + * @cmd_buf: used by the write_reg + * @prepare: [OPTIONAL] do some preparations for the + * read/write/erase/lock/unlock operations + * @unprepare: [OPTIONAL] do some post work after the + * read/write/erase/lock/unlock operations + * @read_xfer: [OPTIONAL] the read fundamental primitive + * @write_xfer: [OPTIONAL] the writefundamental primitive + * @read_reg: [DRIVER-SPECIFIC] read out the register + * @write_reg: [DRIVER-SPECIFIC] write data to the register + * @read_id: [REPLACEABLE] read out the ID data, and find + * the proper spi_device_id + * @wait_till_ready: [REPLACEABLE] wait till the NOR becomes ready + * @read: [DRIVER-SPECIFIC] read data from the SPI NOR + * @write: [DRIVER-SPECIFIC] write data to the SPI NOR + * @erase: [DRIVER-SPECIFIC] erase a sector of the SPI NOR + * at the offset @offs + * @priv: the private data + */ +struct spi_nor { + struct mtd_info *mtd; + struct mutex lock; + struct device *dev; + u32 page_size; + u8 addr_width; + u8 erase_opcode; + u8 read_opcode; + u8 read_dummy; + u8 program_opcode; + enum read_mode flash_read; + bool sst_write_second; + struct spi_nor_xfer_cfg cfg; + u8 cmd_buf[SPI_NOR_MAX_CMD_SIZE]; + + int (*prepare)(struct spi_nor *nor, enum spi_nor_ops ops); + void (*unprepare)(struct spi_nor *nor, enum spi_nor_ops ops); + int (*read_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg, + u8 *buf, size_t len); + int (*write_xfer)(struct spi_nor *nor, struct spi_nor_xfer_cfg *cfg, + u8 *buf, size_t len); + int (*read_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len); + int (*write_reg)(struct spi_nor *nor, u8 opcode, u8 *buf, int len, + int write_enable); + const struct spi_device_id *(*read_id)(struct spi_nor *nor); + int (*wait_till_ready)(struct spi_nor *nor); + + int (*read)(struct spi_nor *nor, loff_t from, + size_t len, size_t *retlen, u_char *read_buf); + void (*write)(struct spi_nor *nor, loff_t to, + size_t len, size_t *retlen, const u_char *write_buf); + int (*erase)(struct spi_nor *nor, loff_t offs); + + void *priv; +}; + +/** + * spi_nor_scan() - scan the SPI NOR + * @nor: the spi_nor structure + * @id: the spi_device_id provided by the driver + * @mode: the read mode supported by the driver + * + * The drivers can use this fuction to scan the SPI NOR. + * In the scanning, it will try to get all the necessary information to + * fill the mtd_info{} and the spi_nor{}. + * + * The board may assigns a spi_device_id with @id which be used to compared with + * the spi_device_id detected by the scanning. + * + * Return: 0 for success, others for failure. + */ +int spi_nor_scan(struct spi_nor *nor, const struct spi_device_id *id, + enum read_mode mode); +extern const struct spi_device_id spi_nor_ids[]; + +/** + * spi_nor_match_id() - find the spi_device_id by the name + * @name: the name of the spi_device_id + * + * The drivers use this function to find the spi_device_id + * specified by the @name. + * + * Return: returns the right spi_device_id pointer on success, + * and returns NULL on failure. + */ +const struct spi_device_id *spi_nor_match_id(char *name); + +#endif