From 364272893877af2ac5f331010d6f6f088c198e31 Mon Sep 17 00:00:00 2001 From: gellert Date: Fri, 15 Aug 2014 16:35:06 +0100 Subject: [PATCH] MMC: added alternative MMC driver MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit mmc: Disable CMD23 transfers on all cards Pending wire-level investigation of these types of transfers and associated errors on bcm2835-mmc, disable for now. Fallback of CMD18/CMD25 transfers will be used automatically by the MMC layer. Reported/Tested-by: Gellert Weisz mmc: bcm2835-mmc: enable DT support for all architectures Both ARCH_BCM2835 and ARCH_BCM270x are built with OF now. Enable Device Tree support for all architectures. Signed-off-by: Noralf Trønnes mmc: bcm2835-mmc: fix probe error handling Probe error handling is broken in several places. Simplify error handling by using device managed functions. Replace pr_{err,info} with dev_{err,info}. Signed-off-by: Noralf Trønnes bcm2835-mmc: Add locks when accessing sdhost registers bcm2835-mmc: Add range of debug options for slowing things down bcm2835-mmc: Add option to disable some delays bcm2835-mmc: Add option to disable MMC_QUIRK_BLK_NO_CMD23 bcm2835-mmc: Default to disabling MMC_QUIRK_BLK_NO_CMD23 bcm2835-mmc: Adding overclocking option Allow a different clock speed to be substitued for a requested 50MHz. This option is exposed using the "overclock_50" DT parameter. Note that the mmc interface is restricted to EVEN integer divisions of 250MHz, and the highest sensible option is 63 (250/4 = 62.5), the next being 125 (250/2) which is much too high. Use at your own risk. bcm2835-mmc: Round up the overclock, so 62 works for 62.5Mhz Also only warn once for each overclock setting. mmc: bcm2835-mmc: Make available on ARCH_BCM2835 Make the bcm2835-mmc driver available for use on ARCH_BCM2835. Signed-off-by: Noralf Trønnes BCM270x_DT: add bcm2835-mmc entry Add Device Tree entry for bcm2835-mmc. In non-DT mode, don't add the device in the board file. Signed-off-by: Noralf Trønnes bcm2835-mmc: Don't overwrite MMC capabilities from DT bcm2835-mmc: Don't override bus width capabilities from devicetree Take out the force setting of the MMC_CAP_4_BIT_DATA host capability so that the result read from devicetree via mmc_of_parse() is preserved. bcm2835-mmc: Only claim one DMA channel With both MMC controllers enabled there are few DMA channels left. The bcm2835-mmc driver only uses DMA in one direction at a time, so it doesn't need to claim two channels. See: https://github.com/raspberrypi/linux/issues/1327 Signed-off-by: Phil Elwell bcm2835-mmc: New timer API mmc: bcm2835-mmc: Support underclocking Support underclocking of the SD bus using the max-frequency DT property (which currently has no DT parameter). The sd_overclock parameter already provides another way to achieve the same thing which should be equivalent in end result, but it is a bug not to support max-frequency as well. See: https://github.com/raspberrypi/linux/issues/2350 Signed-off-by: Phil Elwell mmc/bcm2835: Recover from MMC_SEND_EXT_CSD If the user issues an "mmc extcsd read", the SD controller receives what it thinks is a SEND_IF_COND command with an unexpected data block. The resulting operations leave the FSM stuck in READWAIT, a state which persists until the MMC framework resets the controller, by which point the root filesystem is likely to have been unmounted. A less heavyweight solution is to detect the condition and nudge the FSM by asserting the (self-clearing) FORCE_DATA_MODE bit. N.B. This workaround was essentially discovered by accident and without a full understanding the inner workings of the controller, so it is fortunate that the "fix" only modifies error paths. See: https://github.com/raspberrypi/linux/issues/2728 Signed-off-by: Phil Elwell bcm2835-mmc: Fix DMA channel leak The BCM2835 MMC host driver requests a DMA channel on probe but neglects to release the channel in the probe error path and on driver unbind. I'm seeing this happen on every boot of the Compute Module 3: On first driver probe, DMA channel 2 is allocated and then leaked with a "could not get clk, deferring probe" message. On second driver probe, channel 4 is allocated. Fix it. Signed-off-by: Lukas Wunner Cc: Frank Pavlic bcm2835-mmc: Fix struct mmc_host leak on probe The BCM2835 MMC host driver requests the bus address of the host's register map on probe. If that fails, the driver leaks the struct mmc_host allocated earlier. Fix it. Signed-off-by: Lukas Wunner Cc: Frank Pavlic bcm2835-mmc: Fix duplicate free_irq() on remove The BCM2835 MMC host driver requests its interrupt as a device-managed resource, so the interrupt is automatically freed after the driver is unbound. However on driver unbind, bcm2835_mmc_remove() frees the interrupt explicitly to avoid invocation of the interrupt handler after driver structures have been torn down. The interrupt is thus freed twice, leading to a WARN splat in __free_irq(). Fix by not requesting the interrupt as a device-managed resource. Signed-off-by: Lukas Wunner Cc: Frank Pavlic bcm2835-mmc: Handle mmc_add_host() errors The BCM2835 MMC host driver calls mmc_add_host() but doesn't check its return value. Errors occurring in that function are therefore not handled. Fix it. Signed-off-by: Lukas Wunner Cc: Frank Pavlic bcm2835-mmc: Deduplicate reset of driver data on remove The BCM2835 MMC host driver sets the device's driver data pointer to NULL on ->remove() even though the driver core subsequently does the same in __device_release_driver(). Drop the duplicate assignment. Signed-off-by: Lukas Wunner Cc: Frank Pavlic bcm2835_mmc: Remove vestigial threaded IRQ With SDIO processing now managed by the MMC framework with a workqueue, the bcm2835_mmc driver no longer needs a threaded IRQ. Signed-off-by: Phil Elwell Add missing dma_unmap_sg calls to free relevant swiotlb bounce buffers. This prevents DMA leaks. Signed-off-by: Yaroslav Rosomakho Limit max_req_size under arm64 (or any other platform that uses swiotlb) to prevent potential buffer overflow due to bouncing. Signed-off-by: Yaroslav Rosomakho --- drivers/mmc/core/block.c | 28 +- drivers/mmc/core/core.c | 3 +- drivers/mmc/core/quirks.h | 8 + drivers/mmc/host/Kconfig | 29 + drivers/mmc/host/Makefile | 1 + drivers/mmc/host/bcm2835-mmc.c | 1576 ++++++++++++++++++++++++++++++++ include/linux/mmc/card.h | 2 + 7 files changed, 1643 insertions(+), 4 deletions(-) create mode 100644 drivers/mmc/host/bcm2835-mmc.c --- a/drivers/mmc/core/block.c +++ b/drivers/mmc/core/block.c @@ -165,6 +165,13 @@ static DEFINE_MUTEX(open_lock); module_param(perdev_minors, int, 0444); MODULE_PARM_DESC(perdev_minors, "Minors numbers to allocate per device"); +/* + * Allow quirks to be overridden for the current card + */ +static char *card_quirks; +module_param(card_quirks, charp, 0644); +MODULE_PARM_DESC(card_quirks, "Force the use of the indicated quirks (a bitfield)"); + static inline int mmc_blk_part_switch(struct mmc_card *card, unsigned int part_type); static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq, @@ -2896,6 +2903,7 @@ static int mmc_blk_probe(struct mmc_card { struct mmc_blk_data *md, *part_md; char cap_str[10]; + char quirk_str[24]; /* * Check that the card supports the command class(es) we need. @@ -2903,7 +2911,16 @@ static int mmc_blk_probe(struct mmc_card if (!(card->csd.cmdclass & CCC_BLOCK_READ)) return -ENODEV; - mmc_fixup_device(card, mmc_blk_fixups); + if (card_quirks) { + unsigned long quirks; + if (kstrtoul(card_quirks, 0, &quirks) == 0) + card->quirks = (unsigned int)quirks; + else + pr_err("mmc_block: Invalid card_quirks parameter '%s'\n", + card_quirks); + } + else + mmc_fixup_device(card, mmc_blk_fixups); card->complete_wq = alloc_workqueue("mmc_complete", WQ_MEM_RECLAIM | WQ_HIGHPRI, 0); @@ -2918,9 +2935,14 @@ static int mmc_blk_probe(struct mmc_card string_get_size((u64)get_capacity(md->disk), 512, STRING_UNITS_2, cap_str, sizeof(cap_str)); - pr_info("%s: %s %s %s %s\n", + if (card->quirks) + snprintf(quirk_str, sizeof(quirk_str), + " (quirks 0x%08x)", card->quirks); + else + quirk_str[0] = '\0'; + pr_info("%s: %s %s %s%s%s\n", md->disk->disk_name, mmc_card_id(card), mmc_card_name(card), - cap_str, md->read_only ? "(ro)" : ""); + cap_str, md->read_only ? " (ro)" : "", quirk_str); if (mmc_blk_alloc_parts(card, md)) goto out; --- a/drivers/mmc/core/core.c +++ b/drivers/mmc/core/core.c @@ -1874,7 +1874,8 @@ EXPORT_SYMBOL(mmc_erase); int mmc_can_erase(struct mmc_card *card) { - if (card->csd.cmdclass & CCC_ERASE && card->erase_size) + if (card->csd.cmdclass & CCC_ERASE && card->erase_size && + !(card->quirks & MMC_QUIRK_ERASE_BROKEN)) return 1; return 0; } --- a/drivers/mmc/core/quirks.h +++ b/drivers/mmc/core/quirks.h @@ -99,6 +99,14 @@ static const struct mmc_fixup __maybe_un MMC_FIXUP("V10016", CID_MANFID_KINGSTON, CID_OEMID_ANY, add_quirk_mmc, MMC_QUIRK_TRIM_BROKEN), + /* + * On some Kingston SD cards, multiple erases of less than 64 + * sectors can cause corruption. + */ + MMC_FIXUP("SD16G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN), + MMC_FIXUP("SD32G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN), + MMC_FIXUP("SD64G", 0x41, 0x3432, add_quirk, MMC_QUIRK_ERASE_BROKEN), + END_FIXUP }; --- a/drivers/mmc/host/Kconfig +++ b/drivers/mmc/host/Kconfig @@ -5,6 +5,35 @@ comment "MMC/SD/SDIO Host Controller Drivers" +config MMC_BCM2835_MMC + tristate "MMC support on BCM2835" + depends on MACH_BCM2708 || MACH_BCM2709 || ARCH_BCM2835 + help + This selects the MMC Interface on BCM2835. + + If you have a controller with this interface, say Y or M here. + + If unsure, say N. + +config MMC_BCM2835_DMA + bool "DMA support on BCM2835 Arasan controller" + depends on MMC_BCM2835_MMC + help + Enable DMA support on the Arasan SDHCI controller in Broadcom 2708 + based chips. + + If unsure, say N. + +config MMC_BCM2835_PIO_DMA_BARRIER + int "Block count limit for PIO transfers" + depends on MMC_BCM2835_MMC && MMC_BCM2835_DMA + range 0 256 + default 2 + help + The inclusive limit in bytes under which PIO will be used instead of DMA + + If unsure, say 2 here. + config MMC_DEBUG bool "MMC host drivers debugging" depends on MMC != n --- a/drivers/mmc/host/Makefile +++ b/drivers/mmc/host/Makefile @@ -24,6 +24,7 @@ obj-$(CONFIG_MMC_SDHCI_F_SDH30) += sdhci obj-$(CONFIG_MMC_SDHCI_MILBEAUT) += sdhci-milbeaut.o obj-$(CONFIG_MMC_SDHCI_SPEAR) += sdhci-spear.o obj-$(CONFIG_MMC_SDHCI_AM654) += sdhci_am654.o +obj-$(CONFIG_MMC_BCM2835_MMC) += bcm2835-mmc.o obj-$(CONFIG_MMC_WBSD) += wbsd.o obj-$(CONFIG_MMC_AU1X) += au1xmmc.o obj-$(CONFIG_MMC_ALCOR) += alcor.o --- /dev/null +++ b/drivers/mmc/host/bcm2835-mmc.c @@ -0,0 +1,1576 @@ +/* + * BCM2835 MMC host driver. + * + * Author: Gellert Weisz + * Copyright 2014 + * + * Based on + * sdhci-bcm2708.c by Broadcom + * sdhci-bcm2835.c by Stephen Warren and Oleksandr Tymoshenko + * sdhci.c and sdhci-pci.c by Pierre Ossman + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see . + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "sdhci.h" + + +#define DRIVER_NAME "mmc-bcm2835" + +#define DBG(f, x...) \ +pr_debug(DRIVER_NAME " [%s()]: " f, __func__, ## x) + +#ifndef CONFIG_MMC_BCM2835_DMA + #define FORCE_PIO +#endif + + +/* the inclusive limit in bytes under which PIO will be used instead of DMA */ +#ifdef CONFIG_MMC_BCM2835_PIO_DMA_BARRIER +#define PIO_DMA_BARRIER CONFIG_MMC_BCM2835_PIO_DMA_BARRIER +#else +#define PIO_DMA_BARRIER 00 +#endif + +#define MIN_FREQ 400000 +#define TIMEOUT_VAL 0xE +#define BCM2835_SDHCI_WRITE_DELAY(f) (((2 * 1000000) / f) + 1) + + +unsigned mmc_debug; +unsigned mmc_debug2; + +struct bcm2835_host { + spinlock_t lock; + + void __iomem *ioaddr; + u32 bus_addr; + + struct mmc_host *mmc; + + u32 timeout; + + int clock; /* Current clock speed */ + u8 pwr; /* Current voltage */ + + unsigned int max_clk; /* Max possible freq */ + unsigned int timeout_clk; /* Timeout freq (KHz) */ + unsigned int clk_mul; /* Clock Muliplier value */ + + struct tasklet_struct finish_tasklet; /* Tasklet structures */ + + struct timer_list timer; /* Timer for timeouts */ + + struct sg_mapping_iter sg_miter; /* SG state for PIO */ + unsigned int blocks; /* remaining PIO blocks */ + + int irq; /* Device IRQ */ + + + u32 ier; /* cached registers */ + + struct mmc_request *mrq; /* Current request */ + struct mmc_command *cmd; /* Current command */ + struct mmc_data *data; /* Current data request */ + unsigned int data_early:1; /* Data finished before cmd */ + + wait_queue_head_t buf_ready_int; /* Waitqueue for Buffer Read Ready interrupt */ + + u32 shadow; + + /*DMA part*/ + struct dma_chan *dma_chan_rxtx; /* DMA channel for reads and writes */ + struct dma_slave_config dma_cfg_rx; + struct dma_slave_config dma_cfg_tx; + struct dma_async_tx_descriptor *tx_desc; /* descriptor */ + + bool have_dma; + bool use_dma; + bool wait_for_dma; + /*end of DMA part*/ + + int max_delay; /* maximum length of time spent waiting */ + + int flags; /* Host attributes */ +#define SDHCI_REQ_USE_DMA (1<<2) /* Use DMA for this req. */ +#define SDHCI_DEVICE_DEAD (1<<3) /* Device unresponsive */ +#define SDHCI_AUTO_CMD12 (1<<6) /* Auto CMD12 support */ +#define SDHCI_AUTO_CMD23 (1<<7) /* Auto CMD23 support */ +#define SDHCI_SDIO_IRQ_ENABLED (1<<9) /* SDIO irq enabled */ + + u32 overclock_50; /* frequency to use when 50MHz is requested (in MHz) */ + u32 max_overclock; /* Highest reported */ +}; + + +static inline void bcm2835_mmc_writel(struct bcm2835_host *host, u32 val, int reg, int from) +{ + unsigned delay; + lockdep_assert_held_once(&host->lock); + writel(val, host->ioaddr + reg); + udelay(BCM2835_SDHCI_WRITE_DELAY(max(host->clock, MIN_FREQ))); + + delay = ((mmc_debug >> 16) & 0xf) << ((mmc_debug >> 20) & 0xf); + if (delay && !((1<lock); + writel(val, host->ioaddr + reg); + + delay = ((mmc_debug >> 24) & 0xf) << ((mmc_debug >> 28) & 0xf); + if (delay) + udelay(delay); +} + +static inline u32 bcm2835_mmc_readl(struct bcm2835_host *host, int reg) +{ + lockdep_assert_held_once(&host->lock); + return readl(host->ioaddr + reg); +} + +static inline void bcm2835_mmc_writew(struct bcm2835_host *host, u16 val, int reg) +{ + u32 oldval = (reg == SDHCI_COMMAND) ? host->shadow : + bcm2835_mmc_readl(host, reg & ~3); + u32 word_num = (reg >> 1) & 1; + u32 word_shift = word_num * 16; + u32 mask = 0xffff << word_shift; + u32 newval = (oldval & ~mask) | (val << word_shift); + + if (reg == SDHCI_TRANSFER_MODE) + host->shadow = newval; + else + bcm2835_mmc_writel(host, newval, reg & ~3, 0); + +} + +static inline void bcm2835_mmc_writeb(struct bcm2835_host *host, u8 val, int reg) +{ + u32 oldval = bcm2835_mmc_readl(host, reg & ~3); + u32 byte_num = reg & 3; + u32 byte_shift = byte_num * 8; + u32 mask = 0xff << byte_shift; + u32 newval = (oldval & ~mask) | (val << byte_shift); + + bcm2835_mmc_writel(host, newval, reg & ~3, 1); +} + + +static inline u16 bcm2835_mmc_readw(struct bcm2835_host *host, int reg) +{ + u32 val = bcm2835_mmc_readl(host, (reg & ~3)); + u32 word_num = (reg >> 1) & 1; + u32 word_shift = word_num * 16; + u32 word = (val >> word_shift) & 0xffff; + + return word; +} + +static inline u8 bcm2835_mmc_readb(struct bcm2835_host *host, int reg) +{ + u32 val = bcm2835_mmc_readl(host, (reg & ~3)); + u32 byte_num = reg & 3; + u32 byte_shift = byte_num * 8; + u32 byte = (val >> byte_shift) & 0xff; + + return byte; +} + +static void bcm2835_mmc_unsignal_irqs(struct bcm2835_host *host, u32 clear) +{ + u32 ier; + + ier = bcm2835_mmc_readl(host, SDHCI_SIGNAL_ENABLE); + ier &= ~clear; + /* change which requests generate IRQs - makes no difference to + the content of SDHCI_INT_STATUS, or the need to acknowledge IRQs */ + bcm2835_mmc_writel(host, ier, SDHCI_SIGNAL_ENABLE, 2); +} + + +static void bcm2835_mmc_dumpregs(struct bcm2835_host *host) +{ + pr_debug(DRIVER_NAME ": =========== REGISTER DUMP (%s)===========\n", + mmc_hostname(host->mmc)); + + pr_debug(DRIVER_NAME ": Sys addr: 0x%08x | Version: 0x%08x\n", + bcm2835_mmc_readl(host, SDHCI_DMA_ADDRESS), + bcm2835_mmc_readw(host, SDHCI_HOST_VERSION)); + pr_debug(DRIVER_NAME ": Blk size: 0x%08x | Blk cnt: 0x%08x\n", + bcm2835_mmc_readw(host, SDHCI_BLOCK_SIZE), + bcm2835_mmc_readw(host, SDHCI_BLOCK_COUNT)); + pr_debug(DRIVER_NAME ": Argument: 0x%08x | Trn mode: 0x%08x\n", + bcm2835_mmc_readl(host, SDHCI_ARGUMENT), + bcm2835_mmc_readw(host, SDHCI_TRANSFER_MODE)); + pr_debug(DRIVER_NAME ": Present: 0x%08x | Host ctl: 0x%08x\n", + bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE), + bcm2835_mmc_readb(host, SDHCI_HOST_CONTROL)); + pr_debug(DRIVER_NAME ": Power: 0x%08x | Blk gap: 0x%08x\n", + bcm2835_mmc_readb(host, SDHCI_POWER_CONTROL), + bcm2835_mmc_readb(host, SDHCI_BLOCK_GAP_CONTROL)); + pr_debug(DRIVER_NAME ": Wake-up: 0x%08x | Clock: 0x%08x\n", + bcm2835_mmc_readb(host, SDHCI_WAKE_UP_CONTROL), + bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL)); + pr_debug(DRIVER_NAME ": Timeout: 0x%08x | Int stat: 0x%08x\n", + bcm2835_mmc_readb(host, SDHCI_TIMEOUT_CONTROL), + bcm2835_mmc_readl(host, SDHCI_INT_STATUS)); + pr_debug(DRIVER_NAME ": Int enab: 0x%08x | Sig enab: 0x%08x\n", + bcm2835_mmc_readl(host, SDHCI_INT_ENABLE), + bcm2835_mmc_readl(host, SDHCI_SIGNAL_ENABLE)); + pr_debug(DRIVER_NAME ": AC12 err: 0x%08x | Slot int: 0x%08x\n", + bcm2835_mmc_readw(host, SDHCI_AUTO_CMD_STATUS), + bcm2835_mmc_readw(host, SDHCI_SLOT_INT_STATUS)); + pr_debug(DRIVER_NAME ": Caps: 0x%08x | Caps_1: 0x%08x\n", + bcm2835_mmc_readl(host, SDHCI_CAPABILITIES), + bcm2835_mmc_readl(host, SDHCI_CAPABILITIES_1)); + pr_debug(DRIVER_NAME ": Cmd: 0x%08x | Max curr: 0x%08x\n", + bcm2835_mmc_readw(host, SDHCI_COMMAND), + bcm2835_mmc_readl(host, SDHCI_MAX_CURRENT)); + pr_debug(DRIVER_NAME ": Host ctl2: 0x%08x\n", + bcm2835_mmc_readw(host, SDHCI_HOST_CONTROL2)); + + pr_debug(DRIVER_NAME ": ===========================================\n"); +} + + +static void bcm2835_mmc_reset(struct bcm2835_host *host, u8 mask) +{ + unsigned long timeout; + unsigned long flags; + + spin_lock_irqsave(&host->lock, flags); + bcm2835_mmc_writeb(host, mask, SDHCI_SOFTWARE_RESET); + + if (mask & SDHCI_RESET_ALL) + host->clock = 0; + + /* Wait max 100 ms */ + timeout = 100; + + /* hw clears the bit when it's done */ + while (bcm2835_mmc_readb(host, SDHCI_SOFTWARE_RESET) & mask) { + if (timeout == 0) { + pr_err("%s: Reset 0x%x never completed.\n", + mmc_hostname(host->mmc), (int)mask); + bcm2835_mmc_dumpregs(host); + return; + } + timeout--; + spin_unlock_irqrestore(&host->lock, flags); + mdelay(1); + spin_lock_irqsave(&host->lock, flags); + } + + if (100-timeout > 10 && 100-timeout > host->max_delay) { + host->max_delay = 100-timeout; + pr_warn("Warning: MMC controller hung for %d ms\n", host->max_delay); + } + spin_unlock_irqrestore(&host->lock, flags); +} + +static void bcm2835_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios); + +static void bcm2835_mmc_init(struct bcm2835_host *host, int soft) +{ + unsigned long flags; + if (soft) + bcm2835_mmc_reset(host, SDHCI_RESET_CMD|SDHCI_RESET_DATA); + else + bcm2835_mmc_reset(host, SDHCI_RESET_ALL); + + host->ier = SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT | + SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT | + SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC | + SDHCI_INT_TIMEOUT | SDHCI_INT_DATA_END | + SDHCI_INT_RESPONSE; + + spin_lock_irqsave(&host->lock, flags); + bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 3); + bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 3); + spin_unlock_irqrestore(&host->lock, flags); + + if (soft) { + /* force clock reconfiguration */ + host->clock = 0; + bcm2835_mmc_set_ios(host->mmc, &host->mmc->ios); + } +} + + + +static void bcm2835_mmc_finish_data(struct bcm2835_host *host); + +static void bcm2835_mmc_dma_complete(void *param) +{ + struct bcm2835_host *host = param; + struct dma_chan *dma_chan; + unsigned long flags; + u32 dir_data; + + spin_lock_irqsave(&host->lock, flags); + + host->use_dma = false; + + if (host->data) { + dma_chan = host->dma_chan_rxtx; + if (host->data->flags & MMC_DATA_WRITE) + dir_data = DMA_TO_DEVICE; + else + dir_data = DMA_FROM_DEVICE; + dma_unmap_sg(dma_chan->device->dev, + host->data->sg, host->data->sg_len, + dir_data); + if (! (host->data->flags & MMC_DATA_WRITE)) + bcm2835_mmc_finish_data(host); + } else if (host->wait_for_dma) { + host->wait_for_dma = false; + tasklet_schedule(&host->finish_tasklet); + } + + spin_unlock_irqrestore(&host->lock, flags); +} + +static void bcm2835_bcm2835_mmc_read_block_pio(struct bcm2835_host *host) +{ + unsigned long flags; + size_t blksize, len, chunk; + + u32 uninitialized_var(scratch); + u8 *buf; + + blksize = host->data->blksz; + chunk = 0; + + local_irq_save(flags); + + while (blksize) { + if (!sg_miter_next(&host->sg_miter)) + BUG(); + + len = min(host->sg_miter.length, blksize); + + blksize -= len; + host->sg_miter.consumed = len; + + buf = host->sg_miter.addr; + + while (len) { + if (chunk == 0) { + scratch = bcm2835_mmc_readl(host, SDHCI_BUFFER); + chunk = 4; + } + + *buf = scratch & 0xFF; + + buf++; + scratch >>= 8; + chunk--; + len--; + } + } + + sg_miter_stop(&host->sg_miter); + + local_irq_restore(flags); +} + +static void bcm2835_bcm2835_mmc_write_block_pio(struct bcm2835_host *host) +{ + unsigned long flags; + size_t blksize, len, chunk; + u32 scratch; + u8 *buf; + + blksize = host->data->blksz; + chunk = 0; + chunk = 0; + scratch = 0; + + local_irq_save(flags); + + while (blksize) { + if (!sg_miter_next(&host->sg_miter)) + BUG(); + + len = min(host->sg_miter.length, blksize); + + blksize -= len; + host->sg_miter.consumed = len; + + buf = host->sg_miter.addr; + + while (len) { + scratch |= (u32)*buf << (chunk * 8); + + buf++; + chunk++; + len--; + + if ((chunk == 4) || ((len == 0) && (blksize == 0))) { + mmc_raw_writel(host, scratch, SDHCI_BUFFER); + chunk = 0; + scratch = 0; + } + } + } + + sg_miter_stop(&host->sg_miter); + + local_irq_restore(flags); +} + + +static void bcm2835_mmc_transfer_pio(struct bcm2835_host *host) +{ + u32 mask; + + BUG_ON(!host->data); + + if (host->blocks == 0) + return; + + if (host->data->flags & MMC_DATA_READ) + mask = SDHCI_DATA_AVAILABLE; + else + mask = SDHCI_SPACE_AVAILABLE; + + while (bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE) & mask) { + + if (host->data->flags & MMC_DATA_READ) + bcm2835_bcm2835_mmc_read_block_pio(host); + else + bcm2835_bcm2835_mmc_write_block_pio(host); + + host->blocks--; + + /* QUIRK used in sdhci.c removes the 'if' */ + /* but it seems this is unnecessary */ + if (host->blocks == 0) + break; + + + } +} + + +static void bcm2835_mmc_transfer_dma(struct bcm2835_host *host) +{ + u32 len, dir_data, dir_slave; + struct dma_async_tx_descriptor *desc = NULL; + struct dma_chan *dma_chan; + + + WARN_ON(!host->data); + + if (!host->data) + return; + + if (host->blocks == 0) + return; + + dma_chan = host->dma_chan_rxtx; + if (host->data->flags & MMC_DATA_READ) { + dir_data = DMA_FROM_DEVICE; + dir_slave = DMA_DEV_TO_MEM; + } else { + dir_data = DMA_TO_DEVICE; + dir_slave = DMA_MEM_TO_DEV; + } + + /* The parameters have already been validated, so this will not fail */ + (void)dmaengine_slave_config(dma_chan, + (dir_data == DMA_FROM_DEVICE) ? + &host->dma_cfg_rx : + &host->dma_cfg_tx); + + BUG_ON(!dma_chan->device); + BUG_ON(!dma_chan->device->dev); + BUG_ON(!host->data->sg); + + len = dma_map_sg(dma_chan->device->dev, host->data->sg, + host->data->sg_len, dir_data); + if (len > 0) { + desc = dmaengine_prep_slave_sg(dma_chan, host->data->sg, + len, dir_slave, + DMA_PREP_INTERRUPT | DMA_CTRL_ACK); + } else { + dev_err(mmc_dev(host->mmc), "dma_map_sg returned zero length\n"); + } + if (desc) { + unsigned long flags; + spin_lock_irqsave(&host->lock, flags); + bcm2835_mmc_unsignal_irqs(host, SDHCI_INT_DATA_AVAIL | + SDHCI_INT_SPACE_AVAIL); + host->tx_desc = desc; + desc->callback = bcm2835_mmc_dma_complete; + desc->callback_param = host; + spin_unlock_irqrestore(&host->lock, flags); + dmaengine_submit(desc); + dma_async_issue_pending(dma_chan); + } else { + dma_unmap_sg(dma_chan->device->dev, host->data->sg, len, dir_data); + } + +} + + + +static void bcm2835_mmc_set_transfer_irqs(struct bcm2835_host *host) +{ + u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL; + u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR; + + if (host->use_dma) + host->ier = (host->ier & ~pio_irqs) | dma_irqs; + else + host->ier = (host->ier & ~dma_irqs) | pio_irqs; + + bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 4); + bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 4); +} + + +static void bcm2835_mmc_prepare_data(struct bcm2835_host *host, struct mmc_command *cmd) +{ + u8 count; + struct mmc_data *data = cmd->data; + + WARN_ON(host->data); + + if (data || (cmd->flags & MMC_RSP_BUSY)) { + count = TIMEOUT_VAL; + bcm2835_mmc_writeb(host, count, SDHCI_TIMEOUT_CONTROL); + } + + if (!data) + return; + + /* Sanity checks */ + BUG_ON(data->blksz * data->blocks > 524288); + BUG_ON(data->blksz > host->mmc->max_blk_size); + BUG_ON(data->blocks > 65535); + + host->data = data; + host->data_early = 0; + host->data->bytes_xfered = 0; + + + if (!(host->flags & SDHCI_REQ_USE_DMA)) { + int flags; + + flags = SG_MITER_ATOMIC; + if (host->data->flags & MMC_DATA_READ) + flags |= SG_MITER_TO_SG; + else + flags |= SG_MITER_FROM_SG; + sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags); + host->blocks = data->blocks; + } + + host->use_dma = host->have_dma && data->blocks > PIO_DMA_BARRIER; + + bcm2835_mmc_set_transfer_irqs(host); + + /* Set the DMA boundary value and block size */ + bcm2835_mmc_writew(host, SDHCI_MAKE_BLKSZ(SDHCI_DEFAULT_BOUNDARY_ARG, + data->blksz), SDHCI_BLOCK_SIZE); + bcm2835_mmc_writew(host, data->blocks, SDHCI_BLOCK_COUNT); + + BUG_ON(!host->data); +} + +static void bcm2835_mmc_set_transfer_mode(struct bcm2835_host *host, + struct mmc_command *cmd) +{ + u16 mode; + struct mmc_data *data = cmd->data; + + if (data == NULL) { + /* clear Auto CMD settings for no data CMDs */ + mode = bcm2835_mmc_readw(host, SDHCI_TRANSFER_MODE); + bcm2835_mmc_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 | + SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE); + return; + } + + WARN_ON(!host->data); + + mode = SDHCI_TRNS_BLK_CNT_EN; + + if ((mmc_op_multi(cmd->opcode) || data->blocks > 1)) { + mode |= SDHCI_TRNS_MULTI; + + /* + * If we are sending CMD23, CMD12 never gets sent + * on successful completion (so no Auto-CMD12). + */ + if (!host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) + mode |= SDHCI_TRNS_AUTO_CMD12; + else if (host->mrq->sbc && (host->flags & SDHCI_AUTO_CMD23)) { + mode |= SDHCI_TRNS_AUTO_CMD23; + bcm2835_mmc_writel(host, host->mrq->sbc->arg, SDHCI_ARGUMENT2, 5); + } + } + + if (data->flags & MMC_DATA_READ) + mode |= SDHCI_TRNS_READ; + if (host->flags & SDHCI_REQ_USE_DMA) + mode |= SDHCI_TRNS_DMA; + + bcm2835_mmc_writew(host, mode, SDHCI_TRANSFER_MODE); +} + +void bcm2835_mmc_send_command(struct bcm2835_host *host, struct mmc_command *cmd) +{ + int flags; + u32 mask; + unsigned long timeout; + + WARN_ON(host->cmd); + + /* Wait max 10 ms */ + timeout = 1000; + + mask = SDHCI_CMD_INHIBIT; + if ((cmd->data != NULL) || (cmd->flags & MMC_RSP_BUSY)) + mask |= SDHCI_DATA_INHIBIT; + + /* We shouldn't wait for data inihibit for stop commands, even + though they might use busy signaling */ + if (host->mrq->data && (cmd == host->mrq->data->stop)) + mask &= ~SDHCI_DATA_INHIBIT; + + while (bcm2835_mmc_readl(host, SDHCI_PRESENT_STATE) & mask) { + if (timeout == 0) { + pr_err("%s: Controller never released inhibit bit(s).\n", + mmc_hostname(host->mmc)); + bcm2835_mmc_dumpregs(host); + cmd->error = -EIO; + tasklet_schedule(&host->finish_tasklet); + return; + } + timeout--; + udelay(10); + } + + if ((1000-timeout)/100 > 1 && (1000-timeout)/100 > host->max_delay) { + host->max_delay = (1000-timeout)/100; + pr_warn("Warning: MMC controller hung for %d ms\n", host->max_delay); + } + + timeout = jiffies; + if (!cmd->data && cmd->busy_timeout > 9000) + timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ; + else + timeout += 10 * HZ; + mod_timer(&host->timer, timeout); + + host->cmd = cmd; + host->use_dma = false; + + bcm2835_mmc_prepare_data(host, cmd); + + bcm2835_mmc_writel(host, cmd->arg, SDHCI_ARGUMENT, 6); + + bcm2835_mmc_set_transfer_mode(host, cmd); + + if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) { + pr_err("%s: Unsupported response type!\n", + mmc_hostname(host->mmc)); + cmd->error = -EINVAL; + tasklet_schedule(&host->finish_tasklet); + return; + } + + if (!(cmd->flags & MMC_RSP_PRESENT)) + flags = SDHCI_CMD_RESP_NONE; + else if (cmd->flags & MMC_RSP_136) + flags = SDHCI_CMD_RESP_LONG; + else if (cmd->flags & MMC_RSP_BUSY) + flags = SDHCI_CMD_RESP_SHORT_BUSY; + else + flags = SDHCI_CMD_RESP_SHORT; + + if (cmd->flags & MMC_RSP_CRC) + flags |= SDHCI_CMD_CRC; + if (cmd->flags & MMC_RSP_OPCODE) + flags |= SDHCI_CMD_INDEX; + + if (cmd->data) + flags |= SDHCI_CMD_DATA; + + bcm2835_mmc_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND); +} + + +static void bcm2835_mmc_finish_data(struct bcm2835_host *host) +{ + struct mmc_data *data; + + BUG_ON(!host->data); + + data = host->data; + host->data = NULL; + + if (data->error) + data->bytes_xfered = 0; + else + data->bytes_xfered = data->blksz * data->blocks; + + /* + * Need to send CMD12 if - + * a) open-ended multiblock transfer (no CMD23) + * b) error in multiblock transfer + */ + if (data->stop && + (data->error || + !host->mrq->sbc)) { + + /* + * The controller needs a reset of internal state machines + * upon error conditions. + */ + if (data->error) { + bcm2835_mmc_reset(host, SDHCI_RESET_CMD); + bcm2835_mmc_reset(host, SDHCI_RESET_DATA); + } + + bcm2835_mmc_send_command(host, data->stop); + } else if (host->use_dma) { + host->wait_for_dma = true; + } else { + tasklet_schedule(&host->finish_tasklet); + } +} + +static void bcm2835_mmc_finish_command(struct bcm2835_host *host) +{ + int i; + + BUG_ON(host->cmd == NULL); + + if (host->cmd->flags & MMC_RSP_PRESENT) { + if (host->cmd->flags & MMC_RSP_136) { + /* CRC is stripped so we need to do some shifting. */ + for (i = 0; i < 4; i++) { + host->cmd->resp[i] = bcm2835_mmc_readl(host, + SDHCI_RESPONSE + (3-i)*4) << 8; + if (i != 3) + host->cmd->resp[i] |= + bcm2835_mmc_readb(host, + SDHCI_RESPONSE + (3-i)*4-1); + } + } else { + host->cmd->resp[0] = bcm2835_mmc_readl(host, SDHCI_RESPONSE); + } + } + + host->cmd->error = 0; + + /* Finished CMD23, now send actual command. */ + if (host->cmd == host->mrq->sbc) { + host->cmd = NULL; + bcm2835_mmc_send_command(host, host->mrq->cmd); + + if (host->mrq->cmd->data && host->use_dma) { + /* DMA transfer starts now, PIO starts after interrupt */ + bcm2835_mmc_transfer_dma(host); + } + } else { + + /* Processed actual command. */ + if (host->data && host->data_early) + bcm2835_mmc_finish_data(host); + + if (!host->cmd->data) + tasklet_schedule(&host->finish_tasklet); + + host->cmd = NULL; + } +} + + +static void bcm2835_mmc_timeout_timer(struct timer_list *t) +{ + struct bcm2835_host *host = from_timer(host, t, timer); + unsigned long flags; + + spin_lock_irqsave(&host->lock, flags); + + if (host->mrq) { + pr_err("%s: Timeout waiting for hardware interrupt.\n", + mmc_hostname(host->mmc)); + bcm2835_mmc_dumpregs(host); + + if (host->data) { + host->data->error = -ETIMEDOUT; + bcm2835_mmc_finish_data(host); + } else { + if (host->cmd) + host->cmd->error = -ETIMEDOUT; + else + host->mrq->cmd->error = -ETIMEDOUT; + + tasklet_schedule(&host->finish_tasklet); + } + } + + spin_unlock_irqrestore(&host->lock, flags); +} + + +static void bcm2835_mmc_enable_sdio_irq_nolock(struct bcm2835_host *host, int enable) +{ + if (!(host->flags & SDHCI_DEVICE_DEAD)) { + if (enable) + host->ier |= SDHCI_INT_CARD_INT; + else + host->ier &= ~SDHCI_INT_CARD_INT; + + bcm2835_mmc_writel(host, host->ier, SDHCI_INT_ENABLE, 7); + bcm2835_mmc_writel(host, host->ier, SDHCI_SIGNAL_ENABLE, 7); + } +} + +static void bcm2835_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable) +{ + struct bcm2835_host *host = mmc_priv(mmc); + unsigned long flags; + + spin_lock_irqsave(&host->lock, flags); + if (enable) + host->flags |= SDHCI_SDIO_IRQ_ENABLED; + else + host->flags &= ~SDHCI_SDIO_IRQ_ENABLED; + + bcm2835_mmc_enable_sdio_irq_nolock(host, enable); + spin_unlock_irqrestore(&host->lock, flags); +} + +static void bcm2835_mmc_cmd_irq(struct bcm2835_host *host, u32 intmask) +{ + + BUG_ON(intmask == 0); + + if (!host->cmd) { + pr_err("%s: Got command interrupt 0x%08x even " + "though no command operation was in progress.\n", + mmc_hostname(host->mmc), (unsigned)intmask); + bcm2835_mmc_dumpregs(host); + return; + } + + if (intmask & SDHCI_INT_TIMEOUT) + host->cmd->error = -ETIMEDOUT; + else if (intmask & (SDHCI_INT_CRC | SDHCI_INT_END_BIT | + SDHCI_INT_INDEX)) { + host->cmd->error = -EILSEQ; + } + + if (host->cmd->error) { + tasklet_schedule(&host->finish_tasklet); + return; + } + + if (intmask & SDHCI_INT_RESPONSE) + bcm2835_mmc_finish_command(host); + +} + +static void bcm2835_mmc_data_irq(struct bcm2835_host *host, u32 intmask) +{ + struct dma_chan *dma_chan; + u32 dir_data; + + BUG_ON(intmask == 0); + + if (!host->data) { + /* + * The "data complete" interrupt is also used to + * indicate that a busy state has ended. See comment + * above in sdhci_cmd_irq(). + */ + if (host->cmd && (host->cmd->flags & MMC_RSP_BUSY)) { + if (intmask & SDHCI_INT_DATA_END) { + bcm2835_mmc_finish_command(host); + return; + } + } + + pr_debug("%s: Got data interrupt 0x%08x even " + "though no data operation was in progress.\n", + mmc_hostname(host->mmc), (unsigned)intmask); + bcm2835_mmc_dumpregs(host); + + return; + } + + if (intmask & SDHCI_INT_DATA_TIMEOUT) + host->data->error = -ETIMEDOUT; + else if (intmask & SDHCI_INT_DATA_END_BIT) + host->data->error = -EILSEQ; + else if ((intmask & SDHCI_INT_DATA_CRC) && + SDHCI_GET_CMD(bcm2835_mmc_readw(host, SDHCI_COMMAND)) + != MMC_BUS_TEST_R) + host->data->error = -EILSEQ; + + if (host->use_dma) { + if (host->data->flags & MMC_DATA_WRITE) { + /* IRQ handled here */ + + dma_chan = host->dma_chan_rxtx; + dir_data = DMA_TO_DEVICE; + dma_unmap_sg(dma_chan->device->dev, + host->data->sg, host->data->sg_len, + dir_data); + + bcm2835_mmc_finish_data(host); + } + + } else { + if (host->data->error) + bcm2835_mmc_finish_data(host); + else { + if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL)) + bcm2835_mmc_transfer_pio(host); + + if (intmask & SDHCI_INT_DATA_END) { + if (host->cmd) { + /* + * Data managed to finish before the + * command completed. Make sure we do + * things in the proper order. + */ + host->data_early = 1; + } else { + bcm2835_mmc_finish_data(host); + } + } + } + } +} + + +static irqreturn_t bcm2835_mmc_irq(int irq, void *dev_id) +{ + irqreturn_t result = IRQ_NONE; + struct bcm2835_host *host = dev_id; + u32 intmask, mask, unexpected = 0; + int max_loops = 16; + + spin_lock(&host->lock); + + intmask = bcm2835_mmc_readl(host, SDHCI_INT_STATUS); + + if (!intmask || intmask == 0xffffffff) { + result = IRQ_NONE; + goto out; + } + + do { + /* Clear selected interrupts. */ + mask = intmask & (SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK | + SDHCI_INT_BUS_POWER); + bcm2835_mmc_writel(host, mask, SDHCI_INT_STATUS, 8); + + + if (intmask & SDHCI_INT_CMD_MASK) + bcm2835_mmc_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK); + + if (intmask & SDHCI_INT_DATA_MASK) + bcm2835_mmc_data_irq(host, intmask & SDHCI_INT_DATA_MASK); + + if (intmask & SDHCI_INT_BUS_POWER) + pr_err("%s: Card is consuming too much power!\n", + mmc_hostname(host->mmc)); + + if (intmask & SDHCI_INT_CARD_INT) { + bcm2835_mmc_enable_sdio_irq_nolock(host, false); + sdio_signal_irq(host->mmc); + } + + intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE | + SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK | + SDHCI_INT_ERROR | SDHCI_INT_BUS_POWER | + SDHCI_INT_CARD_INT); + + if (intmask) { + unexpected |= intmask; + bcm2835_mmc_writel(host, intmask, SDHCI_INT_STATUS, 9); + } + + if (result == IRQ_NONE) + result = IRQ_HANDLED; + + intmask = bcm2835_mmc_readl(host, SDHCI_INT_STATUS); + } while (intmask && --max_loops); +out: + spin_unlock(&host->lock); + + if (unexpected) { + pr_err("%s: Unexpected interrupt 0x%08x.\n", + mmc_hostname(host->mmc), unexpected); + bcm2835_mmc_dumpregs(host); + } + + return result; +} + + +static void bcm2835_mmc_ack_sdio_irq(struct mmc_host *mmc) +{ + struct bcm2835_host *host = mmc_priv(mmc); + unsigned long flags; + + spin_lock_irqsave(&host->lock, flags); + if (host->flags & SDHCI_SDIO_IRQ_ENABLED) + bcm2835_mmc_enable_sdio_irq_nolock(host, true); + spin_unlock_irqrestore(&host->lock, flags); +} + +void bcm2835_mmc_set_clock(struct bcm2835_host *host, unsigned int clock) +{ + int div = 0; /* Initialized for compiler warning */ + int real_div = div, clk_mul = 1; + u16 clk = 0; + unsigned long timeout; + unsigned int input_clock = clock; + + if (host->overclock_50 && (clock == 50000000)) + clock = host->overclock_50 * 1000000 + 999999; + + host->mmc->actual_clock = 0; + + bcm2835_mmc_writew(host, 0, SDHCI_CLOCK_CONTROL); + + if (clock == 0) + return; + + /* Version 3.00 divisors must be a multiple of 2. */ + if (host->max_clk <= clock) + div = 1; + else { + for (div = 2; div < SDHCI_MAX_DIV_SPEC_300; + div += 2) { + if ((host->max_clk / div) <= clock) + break; + } + } + + real_div = div; + div >>= 1; + + if (real_div) + clock = (host->max_clk * clk_mul) / real_div; + host->mmc->actual_clock = clock; + + if ((clock > input_clock) && (clock > host->max_overclock)) { + pr_warn("%s: Overclocking to %dHz\n", + mmc_hostname(host->mmc), clock); + host->max_overclock = clock; + } + + clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT; + clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN) + << SDHCI_DIVIDER_HI_SHIFT; + clk |= SDHCI_CLOCK_INT_EN; + bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL); + + /* Wait max 20 ms */ + timeout = 20; + while (!((clk = bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL)) + & SDHCI_CLOCK_INT_STABLE)) { + if (timeout == 0) { + pr_err("%s: Internal clock never " + "stabilised.\n", mmc_hostname(host->mmc)); + bcm2835_mmc_dumpregs(host); + return; + } + timeout--; + mdelay(1); + } + + if (20-timeout > 10 && 20-timeout > host->max_delay) { + host->max_delay = 20-timeout; + pr_warn("Warning: MMC controller hung for %d ms\n", host->max_delay); + } + + clk |= SDHCI_CLOCK_CARD_EN; + bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL); +} + +static void bcm2835_mmc_request(struct mmc_host *mmc, struct mmc_request *mrq) +{ + struct bcm2835_host *host; + unsigned long flags; + + host = mmc_priv(mmc); + + spin_lock_irqsave(&host->lock, flags); + + WARN_ON(host->mrq != NULL); + + host->mrq = mrq; + + if (mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23)) + bcm2835_mmc_send_command(host, mrq->sbc); + else + bcm2835_mmc_send_command(host, mrq->cmd); + + spin_unlock_irqrestore(&host->lock, flags); + + if (!(mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23)) && mrq->cmd->data && host->use_dma) { + /* DMA transfer starts now, PIO starts after interrupt */ + bcm2835_mmc_transfer_dma(host); + } +} + + +static void bcm2835_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) +{ + + struct bcm2835_host *host = mmc_priv(mmc); + unsigned long flags; + u8 ctrl; + u16 clk, ctrl_2; + + pr_debug("bcm2835_mmc_set_ios: clock %d, pwr %d, bus_width %d, timing %d, vdd %d, drv_type %d\n", + ios->clock, ios->power_mode, ios->bus_width, + ios->timing, ios->signal_voltage, ios->drv_type); + + spin_lock_irqsave(&host->lock, flags); + + if (!ios->clock || ios->clock != host->clock) { + bcm2835_mmc_set_clock(host, ios->clock); + host->clock = ios->clock; + } + + if (host->pwr != SDHCI_POWER_330) { + host->pwr = SDHCI_POWER_330; + bcm2835_mmc_writeb(host, SDHCI_POWER_330 | SDHCI_POWER_ON, SDHCI_POWER_CONTROL); + } + + ctrl = bcm2835_mmc_readb(host, SDHCI_HOST_CONTROL); + + /* set bus width */ + ctrl &= ~SDHCI_CTRL_8BITBUS; + if (ios->bus_width == MMC_BUS_WIDTH_4) + ctrl |= SDHCI_CTRL_4BITBUS; + else + ctrl &= ~SDHCI_CTRL_4BITBUS; + + ctrl &= ~SDHCI_CTRL_HISPD; /* NO_HISPD_BIT */ + + + bcm2835_mmc_writeb(host, ctrl, SDHCI_HOST_CONTROL); + /* + * We only need to set Driver Strength if the + * preset value enable is not set. + */ + ctrl_2 = bcm2835_mmc_readw(host, SDHCI_HOST_CONTROL2); + ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK; + if (ios->drv_type == MMC_SET_DRIVER_TYPE_A) + ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A; + else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C) + ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C; + + bcm2835_mmc_writew(host, ctrl_2, SDHCI_HOST_CONTROL2); + + /* Reset SD Clock Enable */ + clk = bcm2835_mmc_readw(host, SDHCI_CLOCK_CONTROL); + clk &= ~SDHCI_CLOCK_CARD_EN; + bcm2835_mmc_writew(host, clk, SDHCI_CLOCK_CONTROL); + + /* Re-enable SD Clock */ + bcm2835_mmc_set_clock(host, host->clock); + bcm2835_mmc_writeb(host, ctrl, SDHCI_HOST_CONTROL); + + spin_unlock_irqrestore(&host->lock, flags); +} + + +static struct mmc_host_ops bcm2835_ops = { + .request = bcm2835_mmc_request, + .set_ios = bcm2835_mmc_set_ios, + .enable_sdio_irq = bcm2835_mmc_enable_sdio_irq, + .ack_sdio_irq = bcm2835_mmc_ack_sdio_irq, +}; + + +static void bcm2835_mmc_tasklet_finish(unsigned long param) +{ + struct bcm2835_host *host; + unsigned long flags; + struct mmc_request *mrq; + + host = (struct bcm2835_host *)param; + + spin_lock_irqsave(&host->lock, flags); + + /* + * If this tasklet gets rescheduled while running, it will + * be run again afterwards but without any active request. + */ + if (!host->mrq) { + spin_unlock_irqrestore(&host->lock, flags); + return; + } + + del_timer(&host->timer); + + mrq = host->mrq; + + /* + * The controller needs a reset of internal state machines + * upon error conditions. + */ + if (!(host->flags & SDHCI_DEVICE_DEAD) && + ((mrq->cmd && mrq->cmd->error) || + (mrq->data && (mrq->data->error || + (mrq->data->stop && mrq->data->stop->error))))) { + + spin_unlock_irqrestore(&host->lock, flags); + bcm2835_mmc_reset(host, SDHCI_RESET_CMD); + bcm2835_mmc_reset(host, SDHCI_RESET_DATA); + spin_lock_irqsave(&host->lock, flags); + } + + host->mrq = NULL; + host->cmd = NULL; + host->data = NULL; + + spin_unlock_irqrestore(&host->lock, flags); + mmc_request_done(host->mmc, mrq); +} + + + +static int bcm2835_mmc_add_host(struct bcm2835_host *host) +{ + struct mmc_host *mmc = host->mmc; + struct device *dev = mmc->parent; +#ifndef FORCE_PIO + struct dma_slave_config cfg; +#endif + int ret; + + bcm2835_mmc_reset(host, SDHCI_RESET_ALL); + + host->clk_mul = 0; + + if (!mmc->f_max || mmc->f_max > host->max_clk) + mmc->f_max = host->max_clk; + mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300; + + /* SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK */ + host->timeout_clk = mmc->f_max / 1000; + mmc->max_busy_timeout = (1 << 27) / host->timeout_clk; + + /* host controller capabilities */ + mmc->caps |= MMC_CAP_CMD23 | MMC_CAP_NEEDS_POLL | + MMC_CAP_SDIO_IRQ | MMC_CAP_SD_HIGHSPEED | + MMC_CAP_MMC_HIGHSPEED; + + mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD; + + host->flags = SDHCI_AUTO_CMD23; + + dev_info(dev, "mmc_debug:%x mmc_debug2:%x\n", mmc_debug, mmc_debug2); +#ifdef FORCE_PIO + dev_info(dev, "Forcing PIO mode\n"); + host->have_dma = false; +#else + if (IS_ERR_OR_NULL(host->dma_chan_rxtx)) { + dev_err(dev, "%s: Unable to initialise DMA channel. Falling back to PIO\n", + DRIVER_NAME); + host->have_dma = false; + } else { + dev_info(dev, "DMA channel allocated"); + + cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + cfg.slave_id = 11; /* DREQ channel */ + + /* Validate the slave configurations */ + + cfg.direction = DMA_MEM_TO_DEV; + cfg.src_addr = 0; + cfg.dst_addr = host->bus_addr + SDHCI_BUFFER; + + ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg); + + if (ret == 0) { + host->dma_cfg_tx = cfg; + + cfg.direction = DMA_DEV_TO_MEM; + cfg.src_addr = host->bus_addr + SDHCI_BUFFER; + cfg.dst_addr = 0; + + ret = dmaengine_slave_config(host->dma_chan_rxtx, &cfg); + } + + if (ret == 0) { + host->dma_cfg_rx = cfg; + + host->have_dma = true; + } else { + pr_err("%s: unable to configure DMA channel. " + "Falling back to PIO\n", + mmc_hostname(mmc)); + dma_release_channel(host->dma_chan_rxtx); + host->dma_chan_rxtx = NULL; + host->have_dma = false; + } + } +#endif + mmc->max_segs = 128; + if (swiotlb_max_segment()) + mmc->max_req_size = (1 << IO_TLB_SHIFT) * IO_TLB_SEGSIZE; + else + mmc->max_req_size = 524288; + mmc->max_seg_size = mmc->max_req_size; + mmc->max_blk_size = 512; + mmc->max_blk_count = 65535; + + /* report supported voltage ranges */ + mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34; + + tasklet_init(&host->finish_tasklet, + bcm2835_mmc_tasklet_finish, (unsigned long)host); + + timer_setup(&host->timer, bcm2835_mmc_timeout_timer, 0); + init_waitqueue_head(&host->buf_ready_int); + + bcm2835_mmc_init(host, 0); + ret = request_irq(host->irq, bcm2835_mmc_irq, IRQF_SHARED, + mmc_hostname(mmc), host); + if (ret) { + dev_err(dev, "Failed to request IRQ %d: %d\n", host->irq, ret); + goto untasklet; + } + + ret = mmc_add_host(mmc); + if (ret) { + dev_err(dev, "could not add MMC host\n"); + goto free_irq; + } + + return 0; + +free_irq: + free_irq(host->irq, host); +untasklet: + tasklet_kill(&host->finish_tasklet); + + return ret; +} + +static int bcm2835_mmc_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *node = dev->of_node; + struct clk *clk; + struct resource *iomem; + struct bcm2835_host *host; + struct mmc_host *mmc; + const __be32 *addr; + int ret; + + mmc = mmc_alloc_host(sizeof(*host), dev); + if (!mmc) + return -ENOMEM; + + mmc->ops = &bcm2835_ops; + host = mmc_priv(mmc); + host->mmc = mmc; + host->timeout = msecs_to_jiffies(1000); + spin_lock_init(&host->lock); + + iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + host->ioaddr = devm_ioremap_resource(dev, iomem); + if (IS_ERR(host->ioaddr)) { + ret = PTR_ERR(host->ioaddr); + goto err; + } + + addr = of_get_address(node, 0, NULL, NULL); + if (!addr) { + dev_err(dev, "could not get DMA-register address\n"); + ret = -ENODEV; + goto err; + } + host->bus_addr = be32_to_cpup(addr); + pr_debug(" - ioaddr %lx, iomem->start %lx, bus_addr %lx\n", + (unsigned long)host->ioaddr, + (unsigned long)iomem->start, + (unsigned long)host->bus_addr); + +#ifndef FORCE_PIO + if (node) { + host->dma_chan_rxtx = dma_request_slave_channel(dev, "rx-tx"); + if (!host->dma_chan_rxtx) + host->dma_chan_rxtx = + dma_request_slave_channel(dev, "tx"); + if (!host->dma_chan_rxtx) + host->dma_chan_rxtx = + dma_request_slave_channel(dev, "rx"); + } else { + dma_cap_mask_t mask; + + dma_cap_zero(mask); + /* we don't care about the channel, any would work */ + dma_cap_set(DMA_SLAVE, mask); + host->dma_chan_rxtx = dma_request_channel(mask, NULL, NULL); + } +#endif + clk = devm_clk_get(dev, NULL); + if (IS_ERR(clk)) { + ret = PTR_ERR(clk); + if (ret == -EPROBE_DEFER) + dev_info(dev, "could not get clk, deferring probe\n"); + else + dev_err(dev, "could not get clk\n"); + goto err; + } + + host->max_clk = clk_get_rate(clk); + + host->irq = platform_get_irq(pdev, 0); + if (host->irq <= 0) { + dev_err(dev, "get IRQ failed\n"); + ret = -EINVAL; + goto err; + } + + if (node) { + mmc_of_parse(mmc); + + /* Read any custom properties */ + of_property_read_u32(node, + "brcm,overclock-50", + &host->overclock_50); + } else { + mmc->caps |= MMC_CAP_4_BIT_DATA; + } + + ret = bcm2835_mmc_add_host(host); + if (ret) + goto err; + + platform_set_drvdata(pdev, host); + + return 0; +err: + if (host->dma_chan_rxtx) + dma_release_channel(host->dma_chan_rxtx); + mmc_free_host(mmc); + + return ret; +} + +static int bcm2835_mmc_remove(struct platform_device *pdev) +{ + struct bcm2835_host *host = platform_get_drvdata(pdev); + unsigned long flags; + int dead; + u32 scratch; + + dead = 0; + scratch = bcm2835_mmc_readl(host, SDHCI_INT_STATUS); + if (scratch == (u32)-1) + dead = 1; + + + if (dead) { + spin_lock_irqsave(&host->lock, flags); + + host->flags |= SDHCI_DEVICE_DEAD; + + if (host->mrq) { + pr_err("%s: Controller removed during " + " transfer!\n", mmc_hostname(host->mmc)); + + host->mrq->cmd->error = -ENOMEDIUM; + tasklet_schedule(&host->finish_tasklet); + } + + spin_unlock_irqrestore(&host->lock, flags); + } + + mmc_remove_host(host->mmc); + + if (!dead) + bcm2835_mmc_reset(host, SDHCI_RESET_ALL); + + free_irq(host->irq, host); + + del_timer_sync(&host->timer); + + tasklet_kill(&host->finish_tasklet); + + if (host->dma_chan_rxtx) + dma_release_channel(host->dma_chan_rxtx); + + mmc_free_host(host->mmc); + + return 0; +} + + +static const struct of_device_id bcm2835_mmc_match[] = { + { .compatible = "brcm,bcm2835-mmc" }, + { } +}; +MODULE_DEVICE_TABLE(of, bcm2835_mmc_match); + + + +static struct platform_driver bcm2835_mmc_driver = { + .probe = bcm2835_mmc_probe, + .remove = bcm2835_mmc_remove, + .driver = { + .name = DRIVER_NAME, + .owner = THIS_MODULE, + .of_match_table = bcm2835_mmc_match, + }, +}; +module_platform_driver(bcm2835_mmc_driver); + +module_param(mmc_debug, uint, 0644); +module_param(mmc_debug2, uint, 0644); +MODULE_ALIAS("platform:mmc-bcm2835"); +MODULE_DESCRIPTION("BCM2835 SDHCI driver"); +MODULE_LICENSE("GPL v2"); +MODULE_AUTHOR("Gellert Weisz"); --- a/include/linux/mmc/card.h +++ b/include/linux/mmc/card.h @@ -271,6 +271,8 @@ struct mmc_card { #define MMC_QUIRK_TRIM_BROKEN (1<<12) /* Skip trim */ #define MMC_QUIRK_BROKEN_HPI (1<<13) /* Disable broken HPI support */ +#define MMC_QUIRK_ERASE_BROKEN (1<<31) /* Skip erase */ + bool reenable_cmdq; /* Re-enable Command Queue */ unsigned int erase_size; /* erase size in sectors */