diff -Nur -x .gitignore -x .git linux-2.6.21.3/arch/avr32/boards/atngw100/flash.c avr32-git/arch/avr32/boards/atngw100/flash.c --- linux-2.6.21.3/arch/avr32/boards/atngw100/flash.c 1970-01-01 01:00:00.000000000 +0100 +++ avr32-git/arch/avr32/boards/atngw100/flash.c 2007-06-06 11:33:46.000000000 +0200 @@ -0,0 +1,95 @@ +/* + * ATNGW100 board-specific flash initialization + * + * Copyright (C) 2005-2006 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include +#include +#include +#include +#include + +#include + +static struct smc_config flash_config __initdata = { + .ncs_read_setup = 0, + .nrd_setup = 40, + .ncs_write_setup = 0, + .nwe_setup = 10, + + .ncs_read_pulse = 80, + .nrd_pulse = 40, + .ncs_write_pulse = 65, + .nwe_pulse = 55, + + .read_cycle = 120, + .write_cycle = 120, + + .bus_width = 2, + .nrd_controlled = 1, + .nwe_controlled = 1, + .byte_write = 1, +}; + +static struct mtd_partition flash_parts[] = { + { + .name = "u-boot", + .offset = 0x00000000, + .size = 0x00020000, /* 128 KiB */ + .mask_flags = MTD_WRITEABLE, + }, + { + .name = "root", + .offset = 0x00020000, + .size = 0x007d0000, + }, + { + .name = "env", + .offset = 0x007f0000, + .size = 0x00010000, + .mask_flags = MTD_WRITEABLE, + }, +}; + +static struct physmap_flash_data flash_data = { + .width = 2, + .nr_parts = ARRAY_SIZE(flash_parts), + .parts = flash_parts, +}; + +static struct resource flash_resource = { + .start = 0x00000000, + .end = 0x007fffff, + .flags = IORESOURCE_MEM, +}; + +static struct platform_device flash_device = { + .name = "physmap-flash", + .id = 0, + .resource = &flash_resource, + .num_resources = 1, + .dev = { + .platform_data = &flash_data, + }, +}; + +/* This needs to be called after the SMC has been initialized */ +static int __init atngw100_flash_init(void) +{ + int ret; + + ret = smc_set_configuration(0, &flash_config); + if (ret < 0) { + printk(KERN_ERR "atngw100: failed to set NOR flash timing\n"); + return ret; + } + + platform_device_register(&flash_device); + + return 0; +} +device_initcall(atngw100_flash_init); diff -Nur -x .gitignore -x .git linux-2.6.21.3/arch/avr32/boards/atngw100/Makefile avr32-git/arch/avr32/boards/atngw100/Makefile --- linux-2.6.21.3/arch/avr32/boards/atngw100/Makefile 1970-01-01 01:00:00.000000000 +0100 +++ avr32-git/arch/avr32/boards/atngw100/Makefile 2007-06-06 11:33:46.000000000 +0200 @@ -0,0 +1 @@ +obj-y += setup.o flash.o diff -Nur -x .gitignore -x .git linux-2.6.21.3/arch/avr32/boards/atngw100/setup.c avr32-git/arch/avr32/boards/atngw100/setup.c --- linux-2.6.21.3/arch/avr32/boards/atngw100/setup.c 1970-01-01 01:00:00.000000000 +0100 +++ avr32-git/arch/avr32/boards/atngw100/setup.c 2007-06-06 11:33:46.000000000 +0200 @@ -0,0 +1,131 @@ +/* + * Board-specific setup code for the ATNGW100 Network Gateway + * + * Copyright (C) 2005-2006 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +#include +#include +#include + +/* Initialized by bootloader-specific startup code. */ +struct tag *bootloader_tags __initdata; + +struct eth_addr { + u8 addr[6]; +}; +static struct eth_addr __initdata hw_addr[2]; +static struct eth_platform_data __initdata eth_data[2]; + +static struct spi_board_info spi0_board_info[] __initdata = { + { + .modalias = "mtd_dataflash", + .max_speed_hz = 10000000, + .chip_select = 0, + }, +}; + +static struct mci_platform_data __initdata mci0_data = { + .detect_pin = GPIO_PIN_PC(25), + .wp_pin = GPIO_PIN_PE(0), +}; + +/* + * The next two functions should go away as the boot loader is + * supposed to initialize the macb address registers with a valid + * ethernet address. But we need to keep it around for a while until + * we can be reasonably sure the boot loader does this. + * + * The phy_id is ignored as the driver will probe for it. + */ +static int __init parse_tag_ethernet(struct tag *tag) +{ + int i; + + i = tag->u.ethernet.mac_index; + if (i < ARRAY_SIZE(hw_addr)) + memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address, + sizeof(hw_addr[i].addr)); + + return 0; +} +__tagtable(ATAG_ETHERNET, parse_tag_ethernet); + +static void __init set_hw_addr(struct platform_device *pdev) +{ + struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + const u8 *addr; + void __iomem *regs; + struct clk *pclk; + + if (!res) + return; + if (pdev->id >= ARRAY_SIZE(hw_addr)) + return; + + addr = hw_addr[pdev->id].addr; + if (!is_valid_ether_addr(addr)) + return; + + /* + * Since this is board-specific code, we'll cheat and use the + * physical address directly as we happen to know that it's + * the same as the virtual address. + */ + regs = (void __iomem __force *)res->start; + pclk = clk_get(&pdev->dev, "pclk"); + if (!pclk) + return; + + clk_enable(pclk); + __raw_writel((addr[3] << 24) | (addr[2] << 16) + | (addr[1] << 8) | addr[0], regs + 0x98); + __raw_writel((addr[5] << 8) | addr[4], regs + 0x9c); + clk_disable(pclk); + clk_put(pclk); +} + +struct platform_device *at32_usart_map[1]; +unsigned int at32_nr_usarts = 1; + +void __init setup_board(void) +{ + at32_map_usart(1, 0); /* USART 1: /dev/ttyS0, DB9 */ + at32_setup_serial_console(0); +} + +static int __init atngw100_init(void) +{ + /* + * ATNGW100 uses 16-bit SDRAM interface, so we don't need to + * reserve any pins for it. + */ + + at32_add_system_devices(); + + at32_add_device_usart(0); + + set_hw_addr(at32_add_device_eth(0, ð_data[0])); + set_hw_addr(at32_add_device_eth(1, ð_data[1])); + + at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); + at32_add_device_mci(0, &mci0_data); + at32_add_device_usba(0); + + return 0; +} +postcore_initcall(atngw100_init); diff -Nur -x .gitignore -x .git linux-2.6.21.3/arch/avr32/boards/atstk1000/atstk1000.h avr32-git/arch/avr32/boards/atstk1000/atstk1000.h --- linux-2.6.21.3/arch/avr32/boards/atstk1000/atstk1000.h 1970-01-01 01:00:00.000000000 +0100 +++ avr32-git/arch/avr32/boards/atstk1000/atstk1000.h 2007-06-06 11:33:46.000000000 +0200 @@ -0,0 +1,15 @@ +/* + * ATSTK1000 setup code: Daughterboard interface + * + * Copyright (C) 2007 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#ifndef __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H +#define __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H + +extern struct atmel_lcdfb_info atstk1000_lcdc_data; + +#endif /* __ARCH_AVR32_BOARDS_ATSTK1000_ATSTK1000_H */ diff -Nur -x .gitignore -x .git linux-2.6.21.3/arch/avr32/boards/atstk1000/atstk1002.c avr32-git/arch/avr32/boards/atstk1000/atstk1002.c --- linux-2.6.21.3/arch/avr32/boards/atstk1000/atstk1002.c 2007-05-24 23:22:47.000000000 +0200 +++ avr32-git/arch/avr32/boards/atstk1000/atstk1002.c 2007-06-06 11:33:46.000000000 +0200 @@ -16,6 +16,8 @@ #include #include +#include