// SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/; #include #include #include "ar7242.dtsi" / { compatible = "tplink,tl-wr2543-v1", "qca,ar7242"; model = "TP-Link TL-WR2543N/ND"; aliases { led-boot = &led_wps; led-failsafe = &led_wps; led-running = &led_wps; led-upgrade = &led_wps; label-mac-device = ð0; }; chosen { bootargs = "console=ttyS0,115200n8"; }; extosc: ref { compatible = "fixed-clock"; #clock-cells = <0>; clock-frequency = <40000000>; }; keys { compatible = "gpio-keys"; reset { label = "reset"; linux,code = ; gpios = <&gpio 11 GPIO_ACTIVE_LOW>; debounce-interval = <60>; }; wps { label = "wps"; linux,code = ; gpios = <&gpio 12 GPIO_ACTIVE_LOW>; debounce-interval = <60>; }; }; leds { compatible = "gpio-leds"; led_wps: wps { label = "tplink:green:wps"; gpios = <&gpio 0 GPIO_ACTIVE_LOW>; }; usb { label = "tplink:green:usb"; gpios = <&gpio 8 GPIO_ACTIVE_LOW>; trigger-sources = <&hub_port>; linux,default-trigger = "usbport"; }; }; ath9k-leds { compatible = "gpio-leds"; wlan2g { label = "tplink:green:wlan2g"; gpios = <&ath9k 0 GPIO_ACTIVE_LOW>; linux,default-trigger = "phy0tpt"; }; wlan5g { label = "tplink:green:wlan5g"; gpios = <&ath9k 1 GPIO_ACTIVE_LOW>; linux,default-trigger = "phy0tpt"; }; }; rtl8367 { compatible = "realtek,rtl8367"; gpio-sda = <&gpio 1 GPIO_ACTIVE_HIGH>; gpio-sck = <&gpio 6 GPIO_ACTIVE_HIGH>; realtek,extif0 = <1 0 1 1 1 1 1 1 2>; mdio-bus { #address-cells = <1>; #size-cells = <0>; status = "okay"; phy0: ethernet-phy@0 { reg = <0>; }; }; }; }; &pll { clocks = <&extosc>; }; &spi { status = "okay"; num-cs = <1>; flash@0 { compatible = "jedec,spi-nor"; reg = <0>; spi-max-frequency = <25000000>; partitions { compatible = "fixed-partitions"; #address-cells = <1>; #size-cells = <1>; uboot: partition@0 { label = "u-boot"; reg = <0x000000 0x020000>; read-only; }; partition@20000 { compatible = "tplink,firmware"; label = "firmware"; reg = <0x020000 0x7d0000>; }; partition@7f0000 { label = "art"; reg = <0x7f0000 0x010000>; read-only; }; }; }; }; &uart { status = "okay"; }; &usb { #address-cells = <1>; #size-cells = <0>; status = "okay"; hub_port: port@1 { reg = <1>; #trigger-source-cells = <0>; }; }; &usb_phy { status = "okay"; }; &pcie { status = "okay"; ath9k: wifi@0,0 { reg = <0x0000 0 0 0 0>; #gpio-cells = <2>; gpio-controller; qca,no-eeprom; mtd-mac-address = <&uboot 0x1fc00>; }; }; ð0 { status = "okay"; phy-mode = "rgmii"; mtd-mac-address = <&uboot 0x1fc00>; phy-handle = <&phy0>; fixed-link { speed = <1000>; full-duplex; }; };