From febc2b831f633d8d6648267952bd43c35689c36f Mon Sep 17 00:00:00 2001 From: TruongSinh Tran-Nguyen Date: Wed, 1 Dec 2021 16:18:17 +0100 Subject: ipq40xx: add support for GL.iNet GL-B2200 This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso [remove redundant check in platform.sh] Signed-off-by: Daniel Golle --- .../ipq40xx/base-files/etc/board.d/02_network | 5 + .../etc/hotplug.d/firmware/11-ath10k-caldata | 5 + .../ipq40xx/base-files/lib/upgrade/platform.sh | 15 + .../arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts | 364 +++++++++++++++++++++ target/linux/ipq40xx/generic/target.mk | 1 + target/linux/ipq40xx/image/generic.mk | 28 ++ .../patches-5.10/901-arm-boot-add-dts-files.patch | 3 +- .../patches-5.4/901-arm-boot-add-dts-files.patch | 3 +- 8 files changed, 422 insertions(+), 2 deletions(-) create mode 100644 target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts (limited to 'target/linux') diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 63209fa49a..c37fc58b22 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -106,6 +106,11 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" ;; + glinet,gl-b2200) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0u@eth0" "1:lan" "2:lan" "3:lan" "5:lan" "0u@eth1" "4:wan" + ;; mobipromo,cm520-79f) ucidef_add_switch "switch0" \ "0u@eth0" "3:lan:2" "4:lan:1" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index f43a3a88b7..8924fb3258 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -9,6 +9,9 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/cal-pci-0000:01:00.0.bin") case "$board" in + glinet,gl-b2200) + caldata_extract "ART" 0x9000 0x2f20 + ;; meraki,mr33) caldata_extract_ubi "ART" 0x9000 0x844 caldata_valid "4408" || caldata_extract "ART" 0x9000 0x844 @@ -64,6 +67,7 @@ case "$FIRMWARE" in ezviz,cs-w3-wd1200g-eup |\ glinet,gl-ap1300 |\ glinet,gl-b1300 |\ + glinet,gl-b2200 |\ glinet,gl-s1300 |\ linksys,ea6350v3 |\ mobipromo,cm520-79f |\ @@ -186,6 +190,7 @@ case "$FIRMWARE" in ezviz,cs-w3-wd1200g-eup |\ glinet,gl-ap1300 |\ glinet,gl-b1300 |\ + glinet,gl-b2200 |\ glinet,gl-s1300 |\ linksys,ea6350v3 |\ mobipromo,cm520-79f |\ diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 8f8494dcff..357e02000a 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -96,6 +96,12 @@ platform_do_upgrade() { qxwlan,e2600ac-c2) nand_do_upgrade "$1" ;; + glinet,gl-b2200) + CI_KERNPART="0:HLOS" + CI_ROOTPART="rootfs" + CI_DATAPART="rootfs_data" + emmc_do_upgrade "$1" + ;; alfa-network,ap120c-ac) part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')" if [ "$part" = "rootfs1" ]; then @@ -166,3 +172,12 @@ platform_do_upgrade() { ;; esac } + +platform_copy_config() { + case "$(board_name)" in + glinet,gl-b2200) + emmc_copy_config + ;; + esac + return 0; +} diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts new file mode 100644 index 0000000000..6b84f78dc4 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4019-gl-b2200.dts @@ -0,0 +1,364 @@ +// SPDX-License-Identifier: GPL-2.0-only OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "GL.iNet GL-B2200"; + compatible = "glinet,gl-b2200", "qcom,ipq4019"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; + }; + + chosen { + bootargs-append = " root=/dev/mmcblk0p2 rw rootwait clk_ignore_unused"; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + status = "okay"; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + switch_lan_bmp = <0x2e>; + switch_wan_bmp = <0x10>; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = <1>; + }; + + reset { + label = "reset"; + gpios = <&tlmm 43 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = <1>; + }; + }; + + leds { + compatible = "gpio-leds"; + + power_blue { + label = "blue:power"; + gpios = <&tlmm 57 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + internet_blue { + label = "blue:internet"; + gpios = <&tlmm 60 GPIO_ACTIVE_HIGH>; + }; + power_white { + label = "white:power"; + gpios = <&tlmm 61 GPIO_ACTIVE_LOW>; + }; + internet_white { + label = "white:internet"; + gpios = <&tlmm 66 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gmac1 { + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + qcom,forced_speed = <1000>; + qcom,forced_duplex = <1>; + vlan_tag = <2 0x10>; +}; + +&gmac0 { + vlan_tag = <1 0x2e>; +}; + +&vqmmc { + status = "okay"; +}; + +&sdhci { + status = "okay"; + pinctrl-0 = <&sd_pins>; + pinctrl-names = "default"; + cd-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&vqmmc>; +}; + +&blsp_dma { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&blsp1_spi1 { + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + partition@c0000 { + label = "CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + partition@d0000 { + label = "DDRPARAMS"; + reg = <0xd0000 0x10000>; + read-only; + }; + + partition@e0000 { + label = "APPSBLENV"; + reg = <0xe0000 0x10000>; + read-only; + }; + + partition@f0000 { + label = "APPSBL"; + reg = <0xf0000 0x80000>; + read-only; + }; + + partition@170000 { + label = "ART"; + reg = <0x170000 0x10000>; + read-only; + }; + }; + }; +}; + +&blsp1_spi2 { + pinctrl-0 = <&spi_1_pins>; + pinctrl-names = "default"; + status = "okay"; + + spidev1: spi@0 { + compatible = "siliconlabs,si3210"; + reg = <0>; + spi-max-frequency = <24000000>; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&blsp1_uart2 { + pinctrl-0 = <&serial_1_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial_1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9", + "gpio10", "gpio11"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + }; + pinconf { + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinconf_cs { + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + spi_1_pins: spi_1_pinmux { + mux { + pins = "gpio44", "gpio46", "gpio47"; + function = "blsp_spi1"; + bias-disable; + }; + cs { + pins = "gpio45"; + function = "gpio"; + bias-pull-up; + }; + reset { + pins = "gpio43"; + function = "gpio"; + output-high; + }; + mux_2 { + pins = "gpio35"; + function = "gpio"; + output-high; + }; + host_int { + pins = "gpio2"; + function = "gpio"; + input; + }; + wake { + pins = "gpio48"; + function = "gpio"; + output-high; + }; + }; + + sd_pins: sd_pins { + pinmux { + function = "sdio"; + pins = "gpio23", "gpio24", "gpio25", "gpio26", + "gpio29", "gpio30", "gpio31", "gpio32"; + drive-strength = <10>; + }; + + pinmux_sd_clk { + function = "sdio"; + pins = "gpio27"; + drive-strength = <16>; + }; + + pinmux_sd7 { + function = "sdio"; + pins = "gpio28"; + drive-strength = <10>; + bias-disable; + }; + }; + +}; + +&pcie0 { + status = "okay"; + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 50 GPIO_ACTIVE_LOW>; + + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + + wifi2: wifi@1,0 { + status = "okay"; + compatible = "qcom,ath10k"; + reg = <0x00010000 0 0 0 0>; + qcom,ath10k-calibration-variant = "GL-B2200"; + }; + }; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-B2200"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "GL-B2200"; +}; diff --git a/target/linux/ipq40xx/generic/target.mk b/target/linux/ipq40xx/generic/target.mk index f5cb1fb19b..e158b1c98b 100644 --- a/target/linux/ipq40xx/generic/target.mk +++ b/target/linux/ipq40xx/generic/target.mk @@ -1 +1,2 @@ BOARDNAME:=Generic +FEATURES+=emmc diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index 0d7d7a30d2..872c4f957f 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -92,6 +92,16 @@ define Build/qsdk-ipq-factory-nand-askey @mv $@.new $@ endef +define Build/qsdk-ipq-app-gpt + cp $@ $@.tmp 2>/dev/null || true + ptgen -g -o $@.tmp -a 1 -l 1024 \ + -t 0x2e -N 0:HLOS -r -p 32M \ + -t 0x83 -N rootfs -r -p 128M \ + -N rootfs_data -p 512M + cat $@.tmp >> $@ + rm $@.tmp +endef + define Build/SenaoFW -$(STAGING_DIR_HOST)/bin/mksenaofw \ -n $(BOARD_NAME) -r $(VENDOR_ID) -p $(1) \ @@ -520,6 +530,24 @@ define Device/glinet_gl-b1300 endef TARGET_DEVICES += glinet_gl-b1300 +define Device/glinet_gl-b2200 + $(call Device/FitzImage) + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := GL-B2200 + SOC := qcom-ipq4019 + DEVICE_DTS_CONFIG := config@ap.dk04.1-c3 + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + IMAGES := emmc.img.gz sysupgrade.bin + IMAGE/emmc.img.gz := qsdk-ipq-app-gpt |\ + pad-to 1024k | append-kernel |\ + pad-to 33792k | append-rootfs |\ + append-metadata | gzip + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata + DEVICE_PACKAGES := ath10k-firmware-qca9888-ct ipq-wifi-glinet_gl-b2200 \ + kmod-fs-ext4 kmod-mmc kmod-spi-dev mkf2fs e2fsprogs kmod-fs-f2fs +endef +TARGET_DEVICES += glinet_gl-b2200 + define Device/glinet_gl-s1300 $(call Device/FitzImage) DEVICE_VENDOR := GL.iNet diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch index 3bd13bf932..b641251423 100644 --- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -902,11 +902,70 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -902,11 +902,71 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -76,6 +76,7 @@ Signed-off-by: John Crispin + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4019-gl-b2200.dtb \ + qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ diff --git a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch index 734d08387a..4270418d6c 100644 --- a/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.4/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -837,11 +837,68 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -837,11 +837,69 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -74,6 +74,7 @@ Signed-off-by: John Crispin + qcom-ipq4029-ap-303h.dtb \ + qcom-ipq4029-ap-365.dtb \ + qcom-ipq4029-gl-b1300.dtb \ ++ qcom-ipq4019-gl-b2200.dtb \ + qcom-ipq4029-gl-s1300.dtb \ + qcom-ipq4029-mr33.dtb \ qcom-ipq8064-ap148.dtb \ -- cgit v1.2.3