From 08768b44d9b6983ae8d2b96434225fef1f5f664c Mon Sep 17 00:00:00 2001 From: INAGAKI Hiroshi Date: Sat, 14 Sep 2019 00:14:36 +0900 Subject: ramips: add support for ELECOM WRC-1167FS MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit ELECOM WRC-1167FS is a 2.4/5 GHz band 11ac (WiFi-5) router, based on MT7628AN. Specification: - SoC : MediaTek MT7628AN - RAM : DDR2 64 MiB (NT5TU32M16FG-AC) - Flash : SPI-NOR 16 MiB (W25Q128JVSIQ) - WLAN : 2.4/5 GHz 2T2R - 2.4 GHz : MediaTek MT7628AN (SoC) - 5 GHz : MediaTek MT7612E - Ethernet : 10/100 Mbps x2 - Switch : MT7628AN (SoC) - LEDs/Keys : 6x, 3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: 3.3V, GND, TX, RX from "J1" marking - 57600n8 - Power : 12 VDC, 1 A Flash instruction using factory image: 1. Boot WRC-1167FS normally 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. Wait ~120 seconds to complete flashing Notes: - Last 0x800000 (8 MiB) in SPI-NOR flash is not used on stock firmware - Additional padding in factory image is required to avoid incomplete flashing on stock firmware MAC addresses: - LAN : BC:5C:4C:xx:xx:68 (Config, ethaddr (text) / Factory, 0x28 (hex)) - WAN : BC:5C:4C:xx:xx:69 (Config, wanaddr (text) / Factory, 0x22 (hex)) - 2.4GHz: BC:5C:4C:xx:xx:6A (Config, rmac (text) / Factory, 0x4 (hex)) - 5GHz : BC:5C:4C:xx:xx:6B (Config, rmac2 (text) / Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi --- target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds | 4 ++++ target/linux/ramips/mt76x8/base-files/etc/board.d/02_network | 5 +++++ 2 files changed, 9 insertions(+) (limited to 'target/linux/ramips/mt76x8/base-files/etc/board.d') diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds index bcbc2ed1e6..47b73e01a2 100755 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds @@ -25,6 +25,10 @@ cudy,wr1000) ucidef_set_led_switch "lan1" "lan1" "blue:lan1" "switch0" "0x08" ucidef_set_led_switch "lan2" "lan2" "blue:lan2" "switch0" "0x04" ;; +elecom,wrc-1167fs) + ucidef_set_led_switch "lan" "lan" "green:lan" "switch0" "0x8" + ucidef_set_led_switch "internet" "internet" "green:internet" "switch0" "0x10" + ;; glinet,gl-mt300n-v2) ucidef_set_led_netdev "wifi_led" "wifi" "red:wlan" "wlan0" ucidef_set_led_switch "wan" "wan" "green:wan" "switch0" "0x1" diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network index 8bbcbb2190..b741b4f9b4 100755 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network @@ -46,6 +46,7 @@ ramips_setup_interfaces() "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "6@eth0" ;; buffalo,wcr-1166ds|\ + elecom,wrc-1167fs|\ wavlink,wl-wn577a2) ucidef_add_switch "switch0" \ "3:lan" "4:wan" "6@eth0" @@ -181,6 +182,10 @@ ramips_setup_macs() zyxel,keenetic-extra-ii) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 0x4)" 1) ;; + elecom,wrc-1167fs) + wan_mac=$(mtd_get_mac_binary factory 0x22) + label_mac=$wan_mac + ;; hilink,hlk-7628n) lan_mac=$(macaddr_setbit_la "$(cat /sys/class/net/eth0/address)") wan_mac=$(macaddr_add "$lan_mac" 1) -- cgit v1.2.3