From 7bc20cb6143e089fae6ad4b173fc42b55bdbecfe Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Rodolphe=20de=20Saint=20L=C3=A9ger?= Date: Wed, 16 Mar 2022 10:19:30 +0100 Subject: ramips: add support for Netgear WN3000RPv3 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit This patch adds support for the Netgear WN3100RPv2 http://www.netgear.com/support/product/wn3100rpv2.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This device seems to be same hardware as a WN3000RPv3 Flash instructions: - Use the Netgear WebUI to upgrade to OpenWRT using the factory image (see note below), - Use the sysupgrade image for upgrading versions from OpenWRT, - TFTP recovery procedure can be used to flash the factory image (preferred method). Note: - The WebUI may not reboot automatically, wait at least 5 minutes before powercycling the device Flashing using TFTP: - Set you IP address to 192.168.1.10/24 (no gateway) - Connect your machine to the Ethernet port - Power off the device and wait for 10 seconds, - Hold the reset button and power on the device (do not release reset), - Hold the reset button until the green light is flashing (Approx. 15s) - launch tftp, set mode to binary and connect to 192.168.1.1 - put the factory firmware image - All leds will switch off (like a power off), this is normal - Wait for the device to reboot in the new OpenWRT image (max 5 mins) - The first boot will take longer than usual. - After boot, the Device IP on the ethernet port is 192.168.1.1 Signed-off-by: Rodolphe de Saint Léger [drop unneeded includes in dts, wrap commit message] Signed-off-by: Sungbo Eo --- target/linux/ramips/mt7620/base-files/etc/board.d/01_leds | 3 ++- target/linux/ramips/mt7620/base-files/etc/board.d/02_network | 1 + 2 files changed, 3 insertions(+), 1 deletion(-) (limited to 'target/linux/ramips/mt7620') diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds index 5f105bd834..1293c34cbf 100644 --- a/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/01_leds @@ -161,7 +161,8 @@ lenovo,newifi-y1s) ucidef_set_led_netdev "wan" "WAN" "blue:internet" "eth0.2" "tx rx" ;; netgear,ex2700|\ -netgear,wn3000rp-v3) +netgear,wn3000rp-v3|\ +netgear,wn3100rp-v2) ucidef_set_led_netdev "wifi_led" "wifi" "green:router" "wlan0" ;; netgear,ex3700|\ diff --git a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network index 3ed72fa3ab..f7bc41669f 100644 --- a/target/linux/ramips/mt7620/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7620/base-files/etc/board.d/02_network @@ -54,6 +54,7 @@ ramips_setup_interfaces() netgear,ex6120|\ netgear,ex6130|\ netgear,wn3000rp-v3|\ + netgear,wn3100rp-v2|\ planex,cs-qr10|\ planex,mzk-ex300np|\ planex,mzk-ex750np|\ -- cgit v1.2.3