From 869376710d70b1e2c9f5265bc8840738794bb280 Mon Sep 17 00:00:00 2001
From: Kristian Evensen <kristian.evensen@gmail.com>
Date: Thu, 16 May 2019 15:38:00 +0200
Subject: ramips: Add support for ZBT WE826-E

ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the
following specifications:

- MT7620A (580 MHz)
- 128MB RAM
- 32MB of flash (SPI NOR)
- 5x 10/100Mbps Ethernet (MT7620A built-in switch)
- 1x microSD slot
- 1x miniPCIe slot (only USB2.0 bus)
- 2x SIM card slots (standard size)
- 1x USB2.0 port
- 1x 2.4GHz wifi (rt2800)
- 10x LEDs (4 GPIO-controlled)
- 1x reset button

The following have been tested and working:
- Ethernet switch
- wifi
- miniPCIe slot
- USB port
- microSD slot
- sysupgrade
- reset button

Installation and recovery:

In order to install OpenWRT the first time or recover the router, you
can use the web-based recovery system. Keep the reset button pressed
during boot and access 192.168.1.1 in your browser when your machine
obtains an IP address.  Upload the firmware to start the recovery
process.

How to swap SIMs:

You control which SIM slot to use by writing 0/1 to
/sys/class/gpio/gpio13/value. In order for the change to take effect,
you can either use AT-commands (AT+CFUN) or power-cycle the modem (write
0/1 to /sys/class/gpio/gpio14/value).

Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
---
 target/linux/ramips/dts/ZBT-WE826-E.dts | 84 +++++++++++++++++++++++++++++++++
 1 file changed, 84 insertions(+)
 create mode 100644 target/linux/ramips/dts/ZBT-WE826-E.dts

(limited to 'target/linux/ramips/dts')

diff --git a/target/linux/ramips/dts/ZBT-WE826-E.dts b/target/linux/ramips/dts/ZBT-WE826-E.dts
new file mode 100644
index 0000000000..ce97b03715
--- /dev/null
+++ b/target/linux/ramips/dts/ZBT-WE826-E.dts
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include "ZBT-WE826.dtsi"
+
+/ {
+	compatible = "zbtlink,zbt-we826-e", "zbtlink,zbt-we826", "ralink,mt7620a-soc";
+	model = "ZBT-WE826-E";
+
+	/delete-node/ leds;
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_power: gsm {
+			label = "zbt-we826-e:blue:gsm";
+			gpios = <&gpio0 9 GPIO_ACTIVE_LOW>;
+		};
+
+		signal {
+			label = "zbt-we826-e:green:signal";
+			gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+		};
+
+		sim {
+			label = "zbt-we826-e:red:sim";
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+
+		air {
+			label = "zbt-we826-e:red:wifi";
+			gpios = <&gpio3 0 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x30000>;
+				read-only;
+			};
+
+			partition@30000 {
+				label = "u-boot-env";
+				reg = <0x30000 0x10000>;
+				read-only;
+			};
+
+			factory: partition@40000 {
+				label = "factory";
+				reg = <0x40000 0x10000>;
+				read-only;
+			};
+
+			firmware: partition@50000 {
+				compatible = "denx,uimage";
+				label = "firmware";
+				reg = <0x50000 0x1fb0000>;
+			};
+		};
+	};
+};
+
+&pinctrl {
+	state_default: pinctrl0 {
+		default {
+			ralink,group = "i2c", "uartf", "wled";
+			ralink,function = "gpio";
+		};
+	};
+};
-- 
cgit v1.2.3